ARRIS Global PX001BNT HD PVR with MOCA User Manual D667 UG
Pace Micro Technology plc HD PVR with MOCA D667 UG
D667-UG-
Remote Data Record
BRINGING TECHNOLOGY HOME
www.pace.com
USER GUIDE
Pace XG1-P
(PX001BNT and PX001BNM)
2
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
CONTENTS
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
CableCARD™ is a trademark of Cable Television Laboratories, Inc.
COMCAST, the COMCAST logo, XFINITY and the XFINITY logo are all trademarks or service marks of Comcast
Corporation or its subsidiaries. All other trademarks and service marks appearing herein are the properties of their
respective owners.
Other trademarks listed herein are the property of their respective owners.
© 2013 Pace plc. All rights reserved. Pace and are trademarks and/or registered trademarks of Pace plc
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Rovi corporation, and is intended for home and other limited
pay-per-view uses only unless otherwise authorized by Rovi corporation. Reverse engineering or disassembly is prohibited.
SAFETY INFORMATION ..................................................................................................3
IMPORTANT SAFETY INSTRUCTIONS ...........................................................................3
Regulatory information .............................................................................................. 5
REAR PANEL .................................................................................................................. 6
CONNECTING THE EQUIPMENT.....................................................................................7
Setup A - Home theater system with HDTV (HDMI® connection) ..............................8
Setup B - Home theater system with HDTV
(Component video / YPbPr connection) ....................................................................9
Connecting the power supply unit to your set-top box ............................................10
Connecting equipment to the wall AC outlets ..........................................................10
Turning your set-top box on and off ........................................................................10
Lightning storms .....................................................................................................10
FRONT PANEL .............................................................................................................. 11
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”) ................................12
3
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
SAFETY INFORMATION
This digital set-top box has been manufactured and tested with your safety
in mind. However, improper use can result in potential electric shock,
property damage or fire hazards. To avoid defeating the safeguards that
have been built into your set-top box, please observe the precautions
discussed in this document.
To ensure correct operation, use this set-top box only with the Pace-
approved power supply unit provided. If you use an unapproved
alternative, you will invalidate the warranty.
Other warnings
To reduce the risk of electric shock, do not remove the cover of your set-
top box. There are no user-serviceable parts inside it.
Do not perform any servicing unless you are qualified to do so. Refer all
servicing to qualified service personnel. Servicing the set-top box yourself
will invalidate the warranty.
To reduce the risk of fire or electric shock, do not expose this set-top box
to rain or moisture.
On the rear panel of your set-top box there is a tamper-evident label that
states ‘Warranty void if broken or removed’.
To avoid possible damage to the internal hard disk, do not pick up or move
your set-top box while it is connected to the power supply. If you want to
move your set-top box, first stop any recording, then turn off your set-top
box and wait 60 seconds before disconnecting it. You should handle your
set-top box carefully, as any damage you cause to the internal hard disk (or
any other component) will invalidate your warranty.
Installation
The installation of your set-top box should be carried out by a qualified
installer and should conform to local codes.
Note to the installer
This reminder is provided to call the attention of the cable-TV-system
installer to Section 820 of the National Electrical Code (USA), which
provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as is practical.
IMPORTANT SAFETY INSTRUCTIONS
Before you install or use the apparatus, you must read and
understand these Important Safety Instructions.
At all times when using the apparatus you must follow
these Important Safety Instructions to reduce the risk of fire,
electrical shock and injury to persons.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into the outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Service address:
Pace Americas Inc.
3701 FAU Boulevard, Suite 200, Boca Raton, Florida 33431 U.S.A.
The lightning flash with arrowhead symbol, within a triangle,
is intended to alert you to the presence of uninsulated
“dangerous” voltages within your set-top box’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a triangle is intended to alert
you to the presence of important instructions in the literature
accompanying your set-top box.
Warnings on the power supply unit
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
4
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
SAFETY INFORMATION (cont.)
In addition to the Important Safety Instructions, please read the Safety
Information below.
Power sources
The model number, serial number, and electrical rating of this set-top box
are on a label on its base.
You must operate your set-top box only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company. If you
move your set-top box between locations at different temperatures, allow it
to reach room temperature before you apply power to it.
Overloading
Do not overload wall AC outlets, extension cords or other power outlets as
this can result in a risk of fire or electric shock.
To avoid possible damage to your set-top box or to a connected TV or
component, all AC power cords must be plugged into properly wired
outlets. As with all electrical products, connection to faulty or defective
components, or the failure to connect your set-top box to a properly wired
outlet, may cause sparking, property damage or damage to any TV or other
component connected to your set-top box and pose a fire hazard.
Lightning
For added protection for your set-top box during a lightning storm, or when
it is left unattended and unused for long periods of time, disconnect your
set-top box from the power supply and disconnect the cable system from
your set-top box. See also item 13 in the Important Safety Instructions.
Ambient temperature
The operating temperature range of your set-top box is 32-104°F. If the
ambient temperature around your set-top box falls outside this range, you
must correct this in order for your set-top box to work correctly and safely.
For example, if the temperature is too high, make sure there is sufficient
ventilation (see below) and that your set-top box is not directly on top of or
underneath other equipment.
Ventilation
Slots and openings in the casing of your set-top box are provided for
ventilation, to ensure reliable operation of your set-top box and to protect it
from overheating.
• Never block the ventilation
openings by placing your set-
top box on a bed, sofa, rug, or
other similar surface. Place it
on a hard, flat surface.
• Never cover the ventilation
openings with items such as
newspapers, table-cloths, or
curtains.
• You can place your set-top
box near other consumer
electronics devices, such as
stereo amplifiers or televisions,
but you must not place it directly on top or underneath them.
3 in.
3 in.
3 in.
Remote DataRecord
• Do not place your set-top box in a built-in installation such as a
bookcase or rack unless proper ventilation is provided and you have
adhered to the manufacturer’s instructions.
• Maintain a minimum distance of three inches around your
set-top box for sufficient ventilation.
See also item 7 in the Important Safety Instructions.
Water and moisture
Do not expose your set-top box to rain or moisture, dripping or splashing,
and ensure that no objects filled with liquids, such as vases, are placed on
your set-top box. See also item 5 in the Important Safety Instructions.
Entry of objects and liquids
Never push objects of any kind into your set-top box through openings
as they may touch dangerous voltage points or short-out parts that could
result in fire or electric shock. Never spill liquid of any kind on your set-
top box.
Transporting
Move the combination of set-top box and cart with care. Quick stops,
excessive force and uneven surfaces may cause the combination of
set-top box and cart to overturn. See also item 12 in the Important Safety
Instructions.
Placement and mounting
Do not place your set-top box on an unstable or uneven surface. Your
set-top box may fall, causing serious injury to a child or adult and serious
damage to your set-top box. If you mount your set-top box, for example
to a wall or ceiling, follow the manufacturer’s instructions and use a
mounting accessory recommended by the manufacturer. See also item 12
in the Important Safety Instructions.
Risk of fire or scorching
Never place naked flame sources, such as lighted candles, on or adjacent
to your set-top box.
Replacement parts
When replacement parts are required, be sure that the service technician
has used replacement parts specified by the manufacturer or that have
the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards. See also item 14 in the
Important Safety Instructions.
Safety check
Upon completion of any servicing or repairs to your set-top box, ask the
service technician to perform safety checks to determine that your set-top
box is in its proper operating condition. See also item 14 in the Important
Safety Instructions.
SAVE THIS INFORMATION FOR FUTURE REFERENCE
5
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
Safety aspects of connections
Full details of the rear panel are on page 6.
Connecting
Do not connect your set-top box (or any other equipment such as a TV or
DVD player) to the power supply until you have properly connected all the
other cables.
Your set-top box is designed for use only with the power supply unit provided.
On the power supply unit there is a label that specifies the correct AC
power supply input for it. Do not connect the power supply unit to any
supply other than this.
Always connect the 12 volt DC cord from the power supply unit to your
set-top box before you insert the AC power cord from the power supply
unit into the wall AC outlet.
Disconnecting
To disconnect power from your set-top box, always detach the power
supply unit from the wall AC outlet (rather than remove the 12 volt cord
from your set-top box).
Therefore you must install your set-top box near to the wall AC outlet,
which should be easily accessible.
If you are in any doubt about the power supply cord, its plug or its
connection, or are not certain that the electrical outlets you are using
are properly wired and grounded, consult a qualified electrician before
proceeding any further.
SAFETY INFORMATION (cont.)
The CABLE IN connector is designed
for connection to a cable network only.
You must not connect any other
equipment, such as a VCR, to this
input.
POWER INPUT
Regulatory information
CAUTION:
• Do not attempt to modify your set-top box without written
authorization from the manufacturer. Unauthorized
modification could void your authority to operate your set-
top box.
• Failure to heed the Safety Information provided by
failing to connect to a properly wired outlet may void the
manufacturer’s warranty.
NOTE
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement
MPE/SAR/RF Exposure Information.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
This equipment was verified for RF exposure and found to comply with
Council Recommendation 1999/519/EC and FCC OET-65 RF exposure
requirements.
WARNING: While this equipment is in operation, a separation distance
of at least 20 centimetres (equal to 8 inches) must be maintained
between the antenna inside the equipment and the bodies of all
persons exposed to the antenna in order to meet the FCC RF exposure
guidelines. Making changes to the antenna or the equipment is not
permitted. Doing so may result in the equipment exceeding the FCC
RF exposure guidelines. This equipment must not be co-located or
operated in conjunction with any other antenna or radio transmitter.
12 volt power
supply unit
To ensure correct operation, use this set-top box only with the Pace-approved
power supply unit provided. If you use an unapproved alternative, you will
invalidate the warranty.
6
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
REAR PANEL
Comp Out*
Component video output
for analog HDTV
Audio Out
Audio outputs
(stereo, L and R)
Cable In
From cable
service-provider
1394*
For connection to
a 1394-compatible
device
eSATA
For connection
to an optional
external hard disk
Power
(Make this
connection
last of all)
Digital Audio Out
Electrical (coaxial)*
and optical S/PDIF
audio output
Ethernet
For connection to
a home network
HDMI HD To TV
HDMI video and
audio outputs
USB
For connection
to USB device
CableCARD™ module
(behind cover) Removal
will interrupt your service
To TV
RF output to
TV (or VCR)
HDMI Input 1 & 2
HDMI ® video and
audio inputs
Video Out
Composite video
output for SDTV
Cable In Connect the cable service here.
To TV Connect to the RF/antenna input on your TV or VCR (optional).
Comp Out* If your HDTV does not have an HDMI connector, but has component video (YPbPr) inputs, connect your HDTV here.
Video Out Connect to the composite video input on your VCR (or a standard TV).
Audio Out For future use during servicing of your set-top box.
Digital Audio Out:
Electrical* and Optical
Connect the lower socket to the optical digital audio input on optional digital audio equipment, such as an audio
decoder or home theater receiver. Or connect the upper socket to the electrical digital audio input on optional digital
audio equipment, such as an audio decoder or home theater receiver.
HDMI HD To TV If your HDTV has an HDMI connector, connect it here for a digital audio/video connection (instead of using the audio
and three analog component video (YPbPr) connectors).
HDMI Input 1 and
HDMI Input 2
Connect another optional HDMI devices (allowing the devices’ outputs to loop through the set-top box to the TV).
USB Connect to the L and R audio inputs on your stereo TV, stereo VCR, or optional stereo amplifier.
eSATA Connect an optional external hard disk.
Ethernet Connect your set-top box into an Ethernet home network (optional).
1394* Connect to a TV with a 1394 port or to any other 1394-compatible device.
+12V DC In Power Connect your set-top box’s power supply unit here. Make this connection last of all.
CableCARD module Removal will interrupt your service.
*Not present on PX001BNM
Note also that the funtionality of some of the connectors depends on the cable service provider.
7
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
WARNINGS
Do not connect your set-top box
(or any other equipment such as
a TV or DVD player) to the power
supply until you have properly
connected all the other cables.
Disconnect your set-top box’s
power supply unit from the
AC power supply before you
disconnect any other equipment
from its rear panel.
The only way to disconnect your
set-top box from the AC power
supply is to remove the power
supply unit from the wall AC outlet
(or switch the wall AC outlet switch,
if present, to its OFF position).
Your set-top box must therefore be
installed near to the wall AC outlet,
which should be easily accessible.
The cable input is designed for
connection to a cable network only.
You must not connect any other
equipment, such as a VCR, to this
input.
Possible setups
In order for you to view programs broadcast in high-definition, your set-top box must be connected to a
suitable HDTV or computer monitor.
Your equipment should have been connected up by your installer. However, if you need to disconnect and
reconnect your equipment, read pages 8 and 9.
There are two typical connection setups for an HDTV, VCR, DVD player, and home theater receiver.
You can take advantage of the digital audio output from your set-top box by connecting a suitable cable
between your home theater receiver and the Digital Audio Out connector (as shown in the diagrams). How
you set up your equipment may depend on your home theater receiver. For example, the optical audio input
may be associated with a particular video input. Consult your home theater user guide for further details.
The setups shown on pages 8 and 9 make efficient use of the connectors on your set-top box. However,
depending on your other equipment and the connectors on it, the person who installed your system may have
chosen to connect things differently.
Recording programs
Both setups allow stereo recording and play-back of video tapes. You hear stereo sound from the home
theater’s loudspeakers. However, your set-top box has an internal hard disk for recording programs. You can
also attach an external hard disk to the rear-panel eSATA port.
RF connections*
Although the RF cables (shown by dashed lines in the diagrams) are not absolutely necessary, we recommend
that you connect them as a back-up. If you use the RF cables, you must tune your TV (and VCR) to your set-
top box’s VHF output channel (3 or 4: consult your cable service-provider to find which channel it is for your
location). Consult the manuals supplied with your TV and VCR for information on how to tune.
* Note that some cable service providers may not enable the RF connection and/or other
features of your set-top box. The functionality depends on your service provider.
CONNECTING THE EQUIPMENT
NOTE
Copy protection via an HDMI secure link
The HDMI link between your set-top box and your HDTV should be a secure link. When your set-top
box is attached via an HDMI cable to an HDCP-compliant (High-bandwidth Digital Content Protection)
HDTV, the HDTV and set-top box negotiate a secure link, which allows your set-top box to transmit full
resolution video (picture) to your HDTV.
Not all HDTVs support HDCP. If your set-top box is connected to an HDTV that does not support it, the
following may be displayed:
Your HDTV does not support HDCP.
Please use the YPbPr component connection to watch TV.
The HDMI output is then disabled, so no picture is transmitted from this connector. In that case, use the
component video connectors to connect up (see Setup B).
8
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
CONNECTING THE EQUIPMENT (cont.)
Setup A - Home theater system with HDTV
(HDMI connection)
Setup A uses an HDMI connector to connect to the HDTV. This displays the highest quality picture on your HDTV and also means there will be no picture
degradation on any copy-protected programs (provided the link remains secure – see page 7).
VCR
DVD
PB/CB
PR/CR
Y
COMPONENT
VIDEO OUT
DIGITAL AUDIO OUT
OPTICALCOAXIAL
ANTENNA/
RF IN
TV / RF
OUT
LEFT
AUDIO OUT
RIGHT
AUDIO OUT
VIDEO OUT
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
OPTICAL
AUDIO IN
COAXIAL
AUDIO IN
DIGITAL AUDIO IN
HOME
THEATER
RECEIVER
LEFT
AUDIO IN
VCR IN
RIGHT
AUDIO IN
VIDEO IN
ANTENNA/
RF IN
HDMI
PB IN
PR IN
Y IN
COMPONENT
VIDEO IN
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
HDTV
POWER
POWER
POWER
POWER
WALL AC OUTLET
WALL AC OUTLET
WALL AC
OUTLETS
CABLE INPUT
NOTE
This diagram shows a video path from your set-top box to a VCR to allow recording by the VCR. It shows
a video path from the VCR to the TV to allow playback of videos. Video signals fed through a VCR may be
affected by copyright protection systems, which can cause picture distortion on your TV.
Do not, therefore, use a path through a VCR to watch your set-top box’s programs.
Use the HDMI path or an alternate direct video path from your set-top box to your TV. Remember to select the
correct input on your TV.
NOTE
This diagram shows power cords
that have 2-blade polarized plugs.
You may need to use a different
type of plug in the region where
you live.
9
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
CONNECTING THE EQUIPMENT (cont.)
Setup B - Home theater system with HDTV
(Component video / YPbPr connection)
Setup B uses a component video connection to connect to your HDTV. This displays a high definition picture on your TV.
VCR
DVD
DIGITAL AUDIO OUT
OPTICALCOAXIAL
ANTENNA/
RF IN
TV / RF
OUT
LEFT
AUDIO OUT
RIGHT
AUDIO OUT
VIDEO OUT
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
OPTICAL
AUDIO IN
COAXIAL
AUDIO IN
DIGITAL AUDIO IN
HOME
THEATER
RECEIVER
LEFT
AUDIO IN
VCR IN
RIGHT
AUDIO IN
VIDEO IN
ANTENNA/
RF IN
PB IN
PR IN
Y IN
COMPONENT
VIDEO IN
LEFT
AUDIO IN
RIGHT
AUDIO IN
VIDEO IN
HDTV
POWER
POWER
POWER
POWER
S-VIDEO
IN
S-VIDEO
OUT
CABLE INPUT
WALL AC
OUTLETS
WALL AC OUTLET
WALL AC OUTLET
NOTE
This diagram shows a video path from your set-top box to a VCR to allow recording by the VCR. It shows
a video path from the VCR to the TV to allow playback of videos. Video signals fed through a VCR may be
affected by copyright protection systems, which can cause picture distortion on your TV.
Do not, therefore, use a path through a VCR to watch your set-top box’s programs. Use the component
video path or an alternate direct video path from your set-top box to your TV. Remember to select the
correct input on your TV.
NOTE
This diagram shows power cords
that have 2-blade polarized plugs.
You may need to use a different
type of plug in the region where
you live.
10
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
CONNECTING THE EQUIPMENT (cont.)
WARNINGS
Do not connect your set-top box (or any other equipment such as a TV or VCR) to the power supply until
you have properly connected all the other cables.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety.
Connecting the power supply unit to your set-top box
Before you insert the power supply unit into the wall AC outlet, connect the 12 volt DC cord from the power
supply unit to the socket labeled “+12V DC In Power” on your set-top box’s rear panel.
Connecting equipment to the wall AC outlets
Connect your set-top box’s power supply unit, and the plugs on the power cords from your TV, DVD player,
and any other equipment, into wall AC outlets. If these outlets have switches, switch them ON.
Turning your set-top box on and off
After you have connected your set-top box’s power supply unit to the wall AC outlet (and switched this outlet
ON, if it has a switch), press the Power button on your set-top box’s front panel to turn it on. The Power
light around the Power button should light up green, to show that your set-top box is on.
To turn your set-top box on or off at any time, press the Power button on the front panel or remote control
(see also below, if you have an RF remote control).
Never turn off your set-top box by simply disconnecting it from the power supply. If you need to disconnect
your set-top box, first stop any recording (if applicable). Then turn off your set-top box by pressing the
Power button on the front panel or your remote control, so that the Power light goes off. Then wait 60
seconds before removing the power supply unit from the wall AC outlet.
Lightning storms
Disconnect your set-top box’s power cord during lightning storms. A lightning storm may affect your set-top
box, if it is on during the storm. It may appear that it has stopped working, but you can easily restore its
operation as follows:
Unplug your set-top box’s power supply unit from the wall AC outlet. Then plug this power supply unit in
again at the wall AC outlet (and, if there is a switch by this outlet, switch it to its ON position).
Remote Data Record
Remote Data Record
A green light around
the button turns on.
To turn your set-top box on,
press the Power button.
Front panel display,
showing the time.
11
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
FRONT PANEL
Remote Data Record
Power button
To turn your set-top
box on/off.
Power light
Lights green when your set-top
box is on and is not lighted
when your set-top box is off.
Display
Shows the time or the current
channel number, and the setting
when you make user settings.
Remote light
Lights when you press a button
on your remote control
(green for an RF remote and
red for an IR remote).
Record light
Lights when a recording is
being made to the internal or
an external hard disk.
Data light
Lights when a message has
been received.
NOTES
Your cable TV service-provider determines the digital channels, services, and screen information that you
see on your TV when you use your set-top box and its remote control.
Consult the information supplied by your cable service-provider for details on how to make the most of the
digital cable services. Also read the operating instructions that are supplied with your remote control.
12
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”)
THE PRODUCT TO WHICH THESE TERMS RELATE (THE “PRODUCT”) INCORPORATES SOFTWARE WHICH IS OWNED BY PACE
plc (“PACE”) OR ITS THIRD PARTY LICENSORS (THE “SOFTWARE”). BEFORE USING THE PRODUCT PLEASE READ THESE
TERMS. IF YOU DO NOT AGREE TO THESE TERMS YOU MAY NOT USE THE PRODUCT AND SHOULD IMMEDIATELY RETURN
THE PRODUCT TO YOUR SUPPLIER. THESE TERMS ALSO APPLY TO ANY MODIFICATIONS, UPDATES OR SUPPLEMENTS TO
THE SOFTWARE PROVIDED TO YOU. FOR PURPOSES OF THESE TERMS, “YOU” MEANS YOU, THE END USER, AND YOUR
PRODUCT SUPPLIER, UNLESS THE CONTEXT REQUIRES OTHERWISE.
A. License Grant and Conditions
1. Pace, or your supplier, if applicable, grants you a non-exclusive, non-transferable, limited license to use the Software solely
as integrated with, incorporated into, or provided for use in connection with the Product.
2. Pace reserves all rights not expressly granted to you under these Terms.
3. You may not transfer any of your limited rights in the Software without the prior written consent of Pace, and if consent
is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND ONLY IF the
transferee has read and agreed to accept these Terms.
4. You must ensure that the copyright, trademark and other protective notices contained in the Software are maintained and not
altered or removed.
5. The Software is protected by copyright and other laws and international copyright and other treaties.
6. The Software provided hereunder is licensed (not sold). Pace is NOT transferring title or any ownership rights in the Software
to you.
7. All title and intellectual property rights in and to the Software and all modifications, updates, enhancements and derivative
works of the Software are owned exclusively by Pace or its licensors and you agree to execute any document reasonably
requested by Pace to evidence such ownership rights.
8. Certain third party software used in connection with the Product may be made directly available to you by operating system
or other third party providers. Use of such Software is also subject to the terms of any applicable agreement between you and
such third party.
B. License Restrictions
Except as expressly permitted herein or by statute you may not:
1. use the Software in conjunction with any other hardware or equipment other than the Product;
2. copy or modify all or any portion of the Software;
3. incorporate all (or any portion of) the Software into other programs developed or used by (or on behalf of) you;
4. reverse engineer, decompile, decrypt or disassemble the Software (or any portion of the Software); or
5. export, transfer or re-export the Software in violation of any applicable law.
C. Open Source Software
Certain components of the Software are subject to either:
(i) the GNU General Public Licence (“GPL”);
(ii) the GNU Lesser General Public Licence (“LGPL”); or
(iii) OpenSSL license.
The foregoing are not subject to the restrictions in Section B. In compliance with the GPL and LGPL Pace makes the source code
of the Linux software, libraries and associated utilities it uses, together with its modifications (if any), available to the public in
source code form at: http://www.pace.com/opensource/request.
You are free to use, modify and distribute the Linux software and any modifications as long as you comply with the terms of the
GPL or LGPL referred to above. The License terms applicable to (i) to (iii) above are available to you, as explained in the section
below entitled Open Source Licenses.
The Software also contains the following:
(iv) SHA library Copyright © 2000-2001, Aaron D. Gifford All rights reserved.
(v) Expat XML Parsing Library
Copyright © 1998, 1999, 2000 Thai Open Source Software Centre Ltd and Clark Cooper.
Copyright © 2001, 2002, 2003 Expat maintainers.
(vi) Expat++ This component of the Software is subject to the Mozilla Public License Version 1.0.
(vii) Base64 Algorithm Copyright © 2001 Bob Trower, Trantor Standard Systems Inc.
Certain additional license terms applicable to (iv) to (vi) above are available to you, as explained in the section below entitled Open Source
Licenses.
13
XG1-P (PX001BNT and PX001BNM) USER GUIDE DRAFT (501-100190x)
D. Termination
These Terms are effective until terminated. You may terminate these Terms by returning the Product to your supplier. These Terms
will terminate automatically without notice if you fail to comply with these Terms or any other written agreement between you and
Pace. Upon termination you must return the Product to your supplier.
E. Disclaimer
1. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND PACE (OR YOUR SUPPLIER), THE SOFTWARE
IS (TO THE EXTENT PERMITTED BY LAW) SUPPLIED “AS IS” AND PACE AND ITS LICENSORS EXPRESSLY EXCLUDE
ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING (BUT NOT LIMITED TO) WARRANTIES OF MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR PURPOSE AND NON-INFRINGEMENT.
2. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND PACE, IN NO CIRCUMSTANCE WILL PACE BE
LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, PUNITIVE OR INCIDENTAL DAMAGE (INCLUDING LOSS
OF PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR THE COST OF PROCUREMENT OF SUBSTITUTE GOODS,
TECHNOLOGY OR SERVICES) ARISING OUT OF THE USE OR THE INABILITY TO USE THE SOFTWARE.
F. General
These Terms are governed by the laws of the State of New York and you may only bring claims exclusively in New York courts and
Pace shall be entitled to bring a claim in the courts of any jurisdiction. Any failure by Pace to enforce any of its rights hereunder
or applicable law shall not constitute a waiver of such rights. Pace’s licensors and suppliers shall be third party beneficiaries of
this License Agreement, as applicable.
YOUR USE OF THE PRODUCT CONSTITUTES YOUR ACKNOWLEDGEMENT THAT YOU HAVE READ THESE TERMS AND AGREE
TO BE BOUND HEREBY.
Open Source Licenses
The software contained in this product may be covered by certain components consisting of free software or open source software.
A list of these components and a copy of the relevant copyright notices and license term notices that are required by such licenses
are available at this web page:
http://www.pace.com/opensource/license
This list may change from time to time and may depend on the model of product or the version of software you have received. If
you are unable to access this web page and wish to have a copy of this list, please contact the Open Source Administrator at: 3701
FAU Boulevard, Suite 200, Boca Raton, Florida 33431 USA. To the extent the terms of these open source or free software licenses
prohibit any of the restrictions in any end user license included with the product, such restrictions will not apply to the applicable
open source or free software component.
TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”) (cont.)
501-100190x
Pace and are trademarks and/or registered trademarks of Pace plc.
www.pace.com