ARRIS SBG6580-2 Wireless Cable Modem Gateways User Manual
ARRIS Group, Inc. Wireless Cable Modem Gateways Users Manual
ARRIS >
Contents
Users Manual
Quick Start Guide
SBG6580
Wireless Cable Modem Gateway
In the Box
SBG6580 Wireless
Cable Modem
Gateway
Power Supply
Ethernet Cable
Software License
& Warranty Card
Quick Start Guide
The SURFboard® SBG6580 is a combination DOCSIS 3.0 cable modem, wireless access point,
and four-port Ethernet router device. It provides ultra high-speed wireless Internet access on
your home or small business network. The SBG6580 connects to the existing coaxial cable
connection in your home and does not require any new wiring.
This quick start guide will help you install your SBG6580 and set up a secure
wireless network connection on your home network. For additional help with
setting up your SBG6580, you can view the SBG6580 Video Tutorials available
online at the ARRIS Support website, www.arris.com/consumer. To access
the videos, you can visit the support website and follow the prompts for
SBG6580 or you can scan the QR code.
To change your wireless network conguration and other advanced gateway settings, see the
SURFboard SBG6580 User Guide available online at the ARRIS Support website. Frequently
asked questions (FAQs) and additional product information are also available.
IMPORTANT! During the installation or gateway activation, you may have to contact your service
provider for assistance. Make sure you have the Gateway Model name (SBG6580), HFC MAC ID,
and Serial number (S/N) listed on the gateway label on the bottom of your SBG6580 (see page 4).
What You Should Know
© 2015 ARRIS Enterprises, Inc. All rights reserved.
No part of this publication may be reproduced or transmitted in any form or by any means without written permission from ARRIS Enterprises, Inc.
ARRIS, SURFboard, and the ARRIS logo are all trademarks or registered trademarks of ARRIS Enterprises, Inc. Other trademarks and trade names
may be used in this document to refer to either the entities claiming the marks and the names of their products. ARRIS disclaims proprietary
interest in the marks and names of others.
All other product or service names are the property of their respective owners. No part of the contents of this document may be reproduced or
transmitted in any form or by any means without written permission of the publisher.
598484-001-a 10/2015
Note: The gateway label is located on the
bottom of your SBG6580.
You may need the following information to
activate your gateway and set up a wireless
network connection:
• Model - Gateway model name.
• SSID - Default name of your wireless
network. It is highly recommended that
you change the default network name
or add additional wireless networks.
• WI-FI SECURITY KEY - Wireless network
password to access your wireless
network using a secure gateway. It is
highly recommended that you change
the default Wi-Fi Security Key to a
more secure password to protect your
wireless network from unauthorized
access.
• S/N - Gateway serial number. Your
service provider may request the serial
number to activate your gateway.
• HFC MAC ID - Your service provider
may request the Media Access Control
(MAC) number to activate your gateway.
Notes
Write your additional wireless network information here
for future reference.
SSID #1:
Wi-Fi Security Key #1:
SSID #2:
Wi-Fi Security Key #2:
SSID #3:
Wi-Fi Security Key #3:
SSID #4:
Wi-Fi Security Key #4:
Additional SSIDs:
Add’l Wi-Fi Security Keys:
4
Gateway Label
BEFORE RETURNING THIS PRODUCT TO THE STORE for any reason, please call ARRIS
Technical Support for assistance: 1-877-466-8646.
For Comcast subscribers only, please visit www.comcast.com/activate before calling
Comcast or ARRIS.
Support
Information Card
Set Up the Wireless Network on Your
Computer
A
Set Up a Wireless Network Connection
Test Your Wireless Network Connection
Start the Gateway Web Manager
B Use the WPS Pairing Button
Power - Lit SOLID when power is connected
Receive - Lit SOLID when locked on a downstream channel
Send - Lit SOLID when locked on an upstream channel
Online - Lit SOLID when connected to the network
Wireless -
WPS Pairing Button
Lit SOLID when wireless pairing with all
devices is complete; Amber LED will FLASH
when WPS is active
Note: Additional items (coaxial cable or RF splitter) that are not included with
your SBG6580 may be needed to complete your gateway installation.
1. Connect the coaxial cable from the cable wall outlet or RF splitter
(optional) to the Cable connector on the rear of your SBG6580.
Use your hand to tighten each connector to avoid damaging them.
2. Connect the Ethernet cable to the Ethernet port on your computer
and to an available Ethernet port on the rear of your SBG6580.
3. Connect the power cord to the Power port on the rear of your
SBG6580 and then plug it into an electrical wall outlet.
This automatically powers ON your SBG6580. Check the front panel
LEDs on your SBG6580. During the initial startup, the Power, Receive,
Send, and Online LEDs should light up. See Front Panel LEDs for
more LED information.
Note: To use Wi-Fi Protected Setup™ (WPS), your computer must support WPS
and also have WPA security compatibility.
The WPS option automatically assigns a random SSID wireless network
name and Wi-Fi Security Key to connect your SBG6580 and other
WPS-enabled wireless devices to your wireless network.
1. Power ON your SBG6580 and other WPS-enabled wireless devices that
you want to connect to your wireless network.
2. Press the WPS button on the SBG6580 front panel.
3. Press and hold the WPS button on your WPS-enabled computer or
other WPS device for ve or more seconds, then release.
4. Repeat steps 2 and 3 for each additional WPS-enabled wireless device.
1. If connected, disconnect the Ethernet cable from your computer and
the SBG6580.
2. Open a web browser on your computer.
3. Type a valid URL (such as www.surfboard.com) in the web browser
address bar and press Enter.
If the website fails to open, please contact your service provider.
Note: The steps for setting up a wireless network may dier slightly depending
on the operating system installed on your computer. The following steps apply
to Windows® 7.
1. From the Windows task bar on your computer, click the following in
sequential order to open the list of available wireless networks:
• Start button
• Control Panel
• Network and Sharing Center
• Connect to a network
2. Scroll down the list and click on the wireless network name or SSID for
your SBG6580.
The SSID is listed on the gateway label on the bottom of your SBG6580.
3. Select Connect automatically to set up automatic log on connections
for the wireless devices on your home network.
4. Click Connect to open the Connect to a Network window.
5. Type your wireless network security code or password in the Security
key eld.
Note: Enter the Wi-Fi Security Key listed on the gateway label or create
your own network password (see the SURFboard SBG6580 User Guide for
more information on changing your network password).
6. Select Hide characters to encrypt your wireless network password for
security purposes and then click OK to complete the wireless network
connection. The Successfully added message should display.
7. Close the Wireless Network Connection window.
During normal operation, the Power, Receive, Send, and Online LEDs on
the SBG6580 front panel should always be lit. The Wireless LED will light
up when a wireless connection is made on your home network. If an LED
did not light up, contact your service provider for assistance.
Front Panel LEDs
3
2
Choose one of the following two options to set up your wireless network
connections. When done, continue with Test Your Wireless Network
Connection.
• Computer Wireless Network Options
• WPS Pairing Button
1. Power ON your computer and log in.
2. Contact your service provider to activate (provision) your SBG6580.
Note: Your service provider may allow for automatic activation which will
automatically launch a special website when you open a web browser. If
so, continue with step 3. Otherwise, contact your service provider.
3. Open a web browser on your computer (such as Internet Explorer,
Google Chrome, Firefox, or Safari).
4. Type a valid URL (such as www.surfboard.com) in the address bar
and press Enter.
The ARRIS website should open. If it fails to open, contact your service
provider to set up your Internet service or activate your SBG6580.
Use the SBG6580 Web Manager to set up and manage your wireless
gateway and network security congurations. To access the web manager:
1. Open a web browser on your computer.
2. Type 192.168.0.1 in the address bar, and press Enter.
3. Type the default user name: admin.
4. Type the default password: motorola.
5. Click Login to open the SBG6580 Web Manager.
Install the Gateway Test the Gateway Connection