ASSALOY Hospitality AS LCU6334 RFID Reader User Manual LCU 6334

Download:
Mirror Download [FCC.gov]
Document ID	2735833
Application ID	IOA6hkO2lyFGRkU1tv3tiQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.68kB (145941 bits)
Date Submitted	2015-09-01 00:00:00
Date Available	2015-09-01 00:00:00
Creation Date	2015-05-12 11:13:39
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2015-05-12 11:13:39
Document Title	Microsoft Word - LCU 6334.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	krigra

Installation of LCU 6334
DRAFT
Copyrights
The information in this document is subject to change at the sole discretion of
ASSA ABLOY AB without notice.
Any use, operation or repair in contravention of this document is at your own risk.
ASSA ABLOY AB does not assume any responsibility for incidental or consequential
damages arising from the use of this manual.
All information and drawings in this document are the property of ASSA ABLOY AB.
Unauthorized use and reproduction is prohibited.
VingCard and Elsafe are registered trademarks of ASSA ABLOY AB.
DRAFT 66 1502 007-0
Installation of LCU 6334
LCU 6334 is used in several different VingCardElsafe products. In each case, LCU 6334
is factory mounted in the end product, so there are no special precautions the customer
needs to take in terms of installing LCU 6334. Each manual for the different end products
where LCU 6334 is applicable will contain the below statements for FCC and Industry Canada.
FCC statements
Changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The concerned end products must be labeled to say 'Contains FCC ID: Y7V –LCU 6334’.
Industry Canada statements
This device complies with Industry Canada Licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
If the IC Certification Number is not visible when a module is installed inside another
device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. In that case, the final concerned
end products must be labeled in a visible area with the following:
'Contains/Contient IC: 9514A-LCU6334'
DRAFT 66 1502 007-0
Asia / Pacific:
E-mail: apac@vingcardelsafe.com
Phone: +65 6305 7670
Europe / Middle East / Africa:
E-mail: emea@vingcardelsafe.com
Phone: +47 69 24 50 00
Latin America:
E-mail: lam@vingcardelsafe.com
Phone: +52 55 36 40 12 00
North America:
E-mail: northamerica@vingcardelsafe.com
Phone: +1 972 907 2273
VingCard Elsafe – P.O. Box 340 – 1402 Ski – Norway – Phone: +47 69 24 50 00
info@vingcardelsafe.com | www.vingcardelsafe.com
Provider of: VingCard Locks & Systems | Elsafe Safes | Orion EMS | PolarBar Minibars
Specifications may change without notice
DRAFT 66 1502 007-0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 4
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2015:05:12 11:13:39
Modify Date                     : 2015:05:12 11:13:39
Title                           : Microsoft Word - LCU 6334.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : krigra

EXIF Metadata provided by EXIF.tools