ASSALOY MODBLE9051 Bluetooth Smart Low Energy Radio Module User Manual 15 0143 Exhibit Cover

ASSA ABLOY Inc. Bluetooth Smart Low Energy Radio Module 15 0143 Exhibit Cover

Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598Certification ExhibitFCC ID: U4A-MODBLE9051IC: 6982A-MODBLE9051FCC Rule Part: 15.247IC Radio Standards Specification: RSS-247ACS Project Number: 15-0143Manufacturer: Assa Abloy Inc.Model: BLE9051
Manual Assa Abloy: Sargent Manufacturing and Corbin Russwin Factory Installaon Instrucons Factory Installaon Instrucons for IN120 reader assemblies Models BIP, BIP-M, BIPS, BIPS-M, BCP and BCP-M, with Bluetooth Smart Model: BLE9051 Assembly: 52-9051 RF Module. FCC Specic Statement: “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-tection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter-ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” General Statements (For all devices): Warning: Changes or modications to this device not expressly approved by Assa Abloy could void the user’s authority to operate the equipment. Industry Canada Specic Statements: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce po-tential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful com-munication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Indus-trie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must ac-cept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio ex-empts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in wholeor in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN1A • PAGE 109/15
Users in the USA and Canada English: Operation is subject to the following two conditions: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure For Mobile Devices include the following: “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-ronment. This equipment should be installed and operated with minimum distance 20cm be-tween the radiator and your body. This transmitter must not be co-located or operating in con-junction with any other antenna or transmitter.” Pour les usagers résidant au Canada (French): L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Énoncé d’exposition à la radiation Pour les appareils mobiles sont les suivants: “Cet équipement est conforme aux limites d’exposition à la radiation RF FCC prévues pour un environnement non contrôlé. Cet équipement doit être installé et doit fonctionner avec une distance minimum de 20 centimètres des utilisateurs et des personnes Environnantes. Cet émetteur ne doit pas être co- localisées ou opérant en conjointement avec une autre antenne ou émetteur Assembly Drawings and Instrucons: 53-5378TAB 52-5376RTAB 52-4890 Factory Conguraon Instrucons: The assembly 52-9051-0000-000 IN120 BT shall be programmed at the manufacturing facility with rmware. The rmware version to be programmed into the unit shall be V5.09, which applies an adversing rate of 20ms and a RSSI tap sensivity of -55dB. Field Conguraon Instrucons: At the customer site, encrypon keys are loaded by a “Mobile Keys” cered technician using an HID conguraon card. This installaon can be performed on mobile enabled readers only. Once the “Mo-bile Keys” have been loaded interface with mobile devices can be achieved. The HID BLE Conguraon applicaon is currently available on Android OS and provides addional conguraon that can be used to congure tap sensivity and transmission power. Transmission power is restricted to a maximum of 0dBm. The HID BLE Conguraon applicaon can be used to upgrade the BLE devices rmware using the OTA technology. Field rmware upgrades can only be performed through and HID cered technician that are authorized to use a controlled administraon card. Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in wholeor in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN1A • PAGE 209/15
Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in wholeor in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN1A • PAGE 309/15
Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in wholeor in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN1A • PAGE 409/15
Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in wholeor in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN1A • PAGE 509/15

Navigation menu