ASSALOY SCYICLS0 S-Series iClass Lock User Manual FCC Part 15

ASSA ABLOY Inc. S-Series iClass Lock FCC Part 15

Contents

Manual - S1 Series

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS0 IC: 6982A-SCYICLS0 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0199.W06.11.A Manufacturer: Assa Abloy, Inc. Model: S1-IA/IK, S2-IA/IK Manual Model S1-IA/IK
A7764B10/10Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Installation Instructions Profile Series v.S1 PoEMortise Lock
1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/101234567Table of ContentsWarning ...................................................................................2General Description .................................................................3Hardware Specifications .........................................................3Electronic Specifications .........................................................3Installation Wiring Overview ...................................................3Installation Wiring ...................................................................4Parts Breakdown .....................................................................8Lock Installation ....................................................................10Operational Check ................................................................1789Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.1Warning Warning SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications.!FCC:NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.Industry Canada:Statement: The term “IC:” before the radio certification number only signifies that Industry Canada technical specifi-cations were met.This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 3Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock General DescriptionThe SARGENT Profile Series v.S1 Mortise Lock is available with either an HID® 125 kHz prox or 13.56 MHz iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet) technology as a proven alternative to traditional access control installations.The v.S1 is a self-contained microprocessor-controlled access control product with non-volatile memory. It uses the existing network cable to communicate with access control systems. The v.S1 lock holds a total of 2400 different user codes. • Using PoE technology coupled with third party software, this v.S1 online lock offers a complete, integrated access control system.• The Profile Series v.S1 Mortise lock may be used for both indoor and outdoor applications. A weather-protective gasket is recommended for outdoor applications. HID and iCLASS are registered trademarks of HID Global Corporation. Electronic SpecificationsHardware Specifications342Installation Wiring Overview5Supplied by OthersA. PoE Frame harness assemblyB. PoE data hinge from McKinney (patent pending)C. PoE Door harness* from McKinneyD. Profile Series S1 PoE Lock * Door width determines lengthNetwork CableNetwork Switch (802.3af) • 2,400 users per lock; 10,000 event audit trail• Multiple time zone and holiday access scheduling• Centralized lock management • Real time door status monitoring • Complete lockset with on-board memory• Available without keypad (Prox/iCLASS only)• ADA compliant • Latch: One-piece stainless steel, 3⁄4"projection• Deadbolt: One-piece hardened stainless steel• Guardbolt: Stainless steel, non-handed• Case - 12 gauge, heavy duty, wrought steel• Inside lever retracts latch and deadbolt• UL Listed (3 hr.) • Handing (RH/LH/RHR/LHR) can be specified but is easily field-reversible without disassembling the lock body• Locks furnished for 1-3/4" doors. Can be furnished for other door sizes upon request. Consult factory. • Wire from EAC Panel to door must be shielded with drain terminated at EAC Panel controller• Outside lever for iCLASS controlled by any HID 13.56 MHz iCLASS credential• Outside lever for prox controlled by any HID 125 kHz prox credential• Outside lever is controlled by any combination of keypad, credential reader, or mechanical cylinder• First-In unlock configuration, either by time or by user (selectable) • Lock down capable• Input Power: PoE Class 1 Device, as defined by IEEE 802.3af, requires up to 4 watts over structured cablingABCDSurface Mount RJ45
4 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock PoE frame harness assembly (From McKinney)PoE data hinge (Patent Pending) (From McKinney)PoE door harness* (From McKinney)6Installation WiringCable: CAT 5e or higher24 AWG shielded with drain wire4-PinMolex-F Molex-F Molex-MCable: CAT 5e,26 AWG stranded,shielded, 100ohmWiring to TIA-568-B StandardRJ45-M Molex-MRJ45-F Jack Cable: CAT 5e or higher24 AWG shielded, 100ohmPERSONA Campus Onlineor Approved Third Party SoftwareB-Splice Crimp ConnectorCertified Integrator (CI) supplies and terminates the B-Splice connector and the Male RJ45 connector from harness to end user provided facility cableSupplied by End UserPoE SwitchPoE LockCeilingSupplied by CIPatch PanelDrain Wire Terminated on RackGroundRing Terminal Secured to Lock Mounting PlateDrain Wire PoE SwitchTerminated toEarth GroundPatch Cable: Patch Panel to PoE Switch4-Pin DPS: Door Position Switch (cylindrical and exits only) Profile Series v.S1 Online P1 PoE lock* Order of installation may vary. Refer to appropriate sections for instructions.Frame-SideHarnessAssembly(15' length)24AWG Stranded Wire for Earth Ground inside 15' Frame HarnessCable drain wire concealed in shrink tubingAEDCA BEDCNotes:• Connectors go on only one way. They cannot placed in an incorrect position.• Do not force and do not offset connec-tors.• Be sure they are completely seated (flush).B
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 5Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock A Frame Harness InstallationSuggested installation of components and wire harness supplied by McKinney: RJ45-M Molex-MCable: CAT 5e or higher24 AWG shielded, 100ohmB-Splice Crimp ConnectorCeilingSupplied by CI Cut end / ceiling-side PoE harness: TIA-568-B Standard Wiring1 2 3 4 5 6 7 8Pair Number Wire PIN1 White/Blue White/Blue 5Blue 42 White/Orange White/Orange 1Orange 23 White/Green White/Green 3Green 64 White/Brown White/Brown 7Brown 8Do not confuse pair numbers with pin numbers. A pair number is used for reference only (e.g.: 10Base-T Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack.1. Feed cut end of harness into hole on hinge-side through single access hole. 2. Push one of the connectors back through hole and feed into separate access hole.Hinge side of PoE harness:BEach of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness:• 4-pin male Molex connector.• 6-pin male Molex connector with ground wire.Frame-SideHarnessAssembly(15' length)24AWG Stranded Wire for Earth Ground inside 15' Frame HarnessCable drain wire concealed in shrink tubing6-pin F4-pin M6-pin M4-pin FDrain WireFrame PoE Hinge (Patent Pending)PoE Data HingeBHinge-side harness connectors:• 4-pin male molex connector• 6-pin male molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors
6 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock Hinge InstallationOrder of installation may vary. Refer to appropriate sections for instructions. Hinge-side harness connectors:• 4-pin male Molex connector• 6-pin male Molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors:• 4-pin Molex connector• 4-pin connectorNotes:• Connectors go on only one way. They cannot be plugged to incorrect position. • Do not force and do not offset connectors.• Be sure they are completely seated (flush).BGround4-Pin MolexJST4-Pin6-pin F 6-pin F 6-pin MCable: CAT 5e,26 AWG stranded,shielded, 100ohmRing Terminal Secured to Lock Mounting PlatePoE LockDoor Harness InstallationOrder of installation may vary. Refer to appropriate sections for instructions. 1. Prop door open.2. Tape the two lock-side 4-pin connectors to the ring terminal.3. Using the ring terminal, carefully fish the assembly through the door channel to the lock. 4. Remove tape from ring terminal and door harness connectors. Hinge-side harness connectors:• 4-pin male Molex connector• 6-pin male Molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors:• 4-pin Molex connector• 4-pin connectorNotes:• Connectors go on only one way. They cannot be placed in an incorrect position. • Do not force and do not offset connectors.• Be sure they are completely seated (flush).CCB4-pin M 4-pin F4-pin FDrain WirePoE Hinge (Patent Pending)DJST 4-PinFrom Hinge Connectors From Lock bodyGround Ring TerminalInside of Door
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 7Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock PoE Lock Wiring DDX NC (GREEN/WHITE)RX COM (WHITE)RX NC (GREEN)DX (WHITE/BLACK)LX NO (RED/YELLOW)LX COM (RED/GREENMotor B (BLACK) Motor A (RED)TB1E1 TB2Controller Board Connectors (Inside Escutcheon)8765432112345678From Lock Body(+) 9VDC (RED) (-) (BLACK)AX/DPS NC (PINK) AX/DPS COM (VIOLET) UnusedUnusedUnusedEGND (GREEN)DPSJ7, J4 JST Connectors(From Hinge) Ground Ring Terminal(From Hinge to Top Left Escutcheon Screw)D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4TB1 E1 TB2PowerRing Terminal From TrimDPS
8 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock 6Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS574899916379210911211131514156
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 9Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock 1 Outside Lever Reference 8200 Catalog for available levers 12 Inside Lever Reference 8200 Catalog for available levers 13 82-0493 O/S Escutcheon only with Cylinder 182-0495 O/S Escutcheon only without Cylinder 14 82-0492 Inside Escutcheon only without Thumb Turn 182-4571 Inside Escutcheon only with Thumb Turn 1552-2431 125kHz Prox Only Assembly (PA)152-2432 Keypad and 125kHz Prox Assembly (PK) OR52-4255 13.56MHz Prox Only Assembly (IA)*When ordered seperately, 13.56 mHz reader assemblies (52-4255/52-4256) ship configured for battery powered operation and need to be configured for PoE/Hardpower use if necessary.52-4256 Keypad and 13.56MHz Prox Assembly (IK)*When ordered seperately, 13.56 mHz reader assemblies (52-4255/52-4256) ship configured for battery powered operation and need to be configured for PoE/Hardpower use if necessary.6 52-4201 S1 Controller Assembly (Double Pulse) 17 52-3855 Battery Cover Assembly 18 01-1212 Security Screw 19 52-2427 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting Screws, Security Allen Wrench)110 Consult Factory Lever Handle Screw (Depends on Lever Style) 111 Consult Factory Inside Adapter Assembly (Depends on Lever Style) 112 Consult Factory Outside Adapter Assembly (Depends On Lever Style) 113 S1-82276-hand-finish Lockbody with Dead Bolt with Cylinder 1S1-82277-hand-finish Lockbody with Dead Bolt without CylinderS1-82278-hand-finish Lockbody without Dead Bolt with CylinderS1-82279-hand-finish Lockbody without Dead Bolt without Cylinder14 82-0084 Faceplate with Dead Bolt (shown) 182-0081 Faceplate without Dead Bolt 115 77-4336 Mortise Screw Pack - Specify Finish (Includes: Wood and Me-tal Lock body Screws, Faceplate Screws, and Strike Screws)116 Consult Factory #43 Mortise Cylinder 1 ITEM PART NO. DESCRIPTION QTY.Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued
10 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock Stand on outside of locked door when determining door hand.B. Door PreparationOutside of Door Inside of DoorStep #1 – Door PreparationA. Verify Hand and Bevel of DoorLock InstallationRibbon Cable Hole (Controller to Keypad)Outside of Cylinder Hole(only with cylinder installation)Lever Handle HoleThrough-bolt HoleRibbon Cable Hole (Controller to Keypad)Inside of Lockbody Wire Hole(only with cylinder installation)Lever Handle Hole*RacewayThrough-bolt HolePre-drilled and/orTapped HolesMortisedPocketPrior to installation, all holes must be free of burrs, debris and sharp edges. Prepare door according to appropriate template (see website www.intelligentopenings.com):• Wood door: A7457 (ships with product)• Metal door: 4533LH Left Hand Hinges Left Open Inward LHRB Left Hand Reverse Bevel Hinges Left Open Outward RHRight Hand Hinges Right Open Inward RHRB Right Hand Reverse Bevel Hinges Right Open Outward 8*Note: Raceway placement in document is approximate. Thumb Turn Lever HoleFig. 1AFig. 1B
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 11Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock Step #2 – How to Change Hand of LockbodyBeveled surface of latchbolt must face strike.The deadlatch is self adjusting.To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody.B. Retaining RingMake sure the plastic retaining ring is seated correctly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side.2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring.Push InRight Hand ShownLocking Guide SlotFig. 2AFig. 2CA. Reverse Lock HandC. Reverse Latch HandRed Locking Piece Indicates Locked SidePlastic Retaining RingOutside of DoorFig. 2BSlot
12 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock Step #3 – Install Lockbody1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lock-body (Fig. 3A).Note: Connectors and wires must be fed through non-cylinder side. 2. The wires from the lockbody exit the inside door prep through the mortise cutout.3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws.Note: Do not completely tighten at this time.Ground Wire(2) 4-Pin Connectors From Hinge Step #4 – Exterior Door OptionsA. Fire Stop PlateFire-rated doors require a fire stop plate on the outside of the door (Fig. 4A).1. Drill (2) 1/8” x 1-1/4” deep holes in the door, if not already present.Refer to template for fire-stop prep locations.2. Attach with flap up and out using (2) #8 x 1/2” self-tapping screws for wood and metal doors.B. Weather ConduitInstall weather conduit (part number 52-2847) on NON Fire-Rated exterior doors only (Fig. 4B).Note: Once weather conduit is assembled, it can be difficult to take apart. (2) #12-24 x 1/2” Long Flat Head Screws for Metal Doors(2) #12 x 1-1/4” Long Flat Head Screws for Metal DoorsFig. 3AMortise Connectors Inside of DoorFig. 4BWeather ConduitFig. 4A(2) 1/8” Diameter Holes RequiredSlot(2) Self-Tapping #8 x 1/2” Screws for Wood and Metal DoorsOutside of DoorFire Stop Plate
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 13Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock Step #6 – Install Outside Escutcheon and Lever Assembly 1A. For fire rated doors, feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket and fire stop plate (Fig. 6A). Note: Install ribbon cable with cable exiting down1B. For non-fire rated doors, feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket (if used) and weather conduit (Fig. 6A). Note: Install ribbon cable with cable exiting down2. With outside lever horizontal, locate the outside escutcheon on the door, while directing the mounting posts through the door and lock body (Fig. 6B). Make sure the lever spindle is properly engaged in lock.3. On the inside of the door, insert spindle into square hole of mortise lock.4. Slide inside adapter and plate assembly over spindle and loosely secure with 2 through bolt screws (#8-32 x 5/8”). Note: For 8276 and 8278, loosely thread cylinder through escutcheon and into the lock body before tightening the lock case screws and escutcheon through bolts. Gasket 82-0500Step #5 – Install Gasket (for Exterior Doors)1. Carefully remove the backing from the gasket. 2. Apply gasket to escutcheon:• Starting in one place, press the adhesive side of the gasket firmly against the escutcheon.• Work around the escutcheon, pressing the sticky side of the gasket firmly against the escutcheon edge.• The gasket should be aligned so that all edges of the escutcheon are covered.3. Attach escutcheon to the door after the wires are connected.Note: The 43 cylinder may be used with or without a gasket.Fig. 5AInside of DoorMortise Lock bodyand AX ConnectorsFig. 6BReader Cable Ground Wire (E1)Antenna (iCLASS)JST 4-PinFrom Hinge Ground Ring TerminalAntenna (iCLASS only)Fig. 6AOutside of DoorKeypad RibbonCable Ground Wire (E1)Keypad RibbonCable Ground Wire (E1)GasketAntenna(iCLASS) OnlyFig. 5B
14 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock Step #7 – Escutcheon Wire ConnectionsImages are shown without gasket. If gasket is necessary, refer to Step #5. Before the controller is attached to the door:1. Attach the reader assembly ribbon cable into the back of the controller assembly (side that faces towards the door when mounted (Fig. 7C Detail). 2. Attach the antenna to the circuit board in the plastic housing under the controller assembly. Note: The difference between the wiring for the iCLASS 13.56 MHz reader and the 125 kHz Prox is that the iCLASS wiring includes an antenna wire.3. Attach the ground wire to the bottom of the controller assembly (E1, Fig. 7A).Step #8 – Additional Wiring ConnectionsLock, DPS and raceway wire connections: 1. Connect the cable from the mortise lock to the bottom of the controller assembly (TB1, Fig. 8A).2. Connect the AX/DPS connector to the 2-pin harness. 3. Push the two connectors from the raceway over the controller assembly, through the gap between the plastic controller assembly and the escutcheon, to the front of the circuit board. Mortise ConnectorGround WireFig. 8ABackAX/DPSInside of DoorGround Ring Terminal132Outside EscutcheonAntenna (iCLASS only)UnusedTB1Reader CableGround WireFig. 7A2Outside Escutcheon123Ground WireReader CableAntenna(iCLASS)1Ground Ring Terminal34-Pin Connectors From Hinge 2Antenna (iCLASS only)Reader Cable14-Pin Connectors From Hinge
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 15Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock Step #9 – Ciruit Board Wiring Before installing escutcheon, route raceway cables and ground attach to front of circuit board. Turn the controller assembly over:1. Route the raceway connectors over the top of the controller assembly and plug into the front of the circuit board (side that faces out when mounted (J7, J4; Fig. 9A).2. Route the 2 ground ring terminals, one from the lock and the other from the hinge wiring, over the top of the controller assembly and con-nect both to the top escutcheon screw. Note: Connectors go on only one way. Do not offset connectors and make sure they are completely seated.Inside of DoorGround Ring TerminalFig. 9AStep #10 – Install Inside Escutcheon1. Gently fold the excess ribbon connector and ground wire into the top hole, JST connectors and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig. 10A). 2. Insert (2) #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon (Fig. 10B)Straighten escutcheons and tighten securely.Inside of DoorFig. 10BFig. 10A
16 1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S1 PoE Mortise Lock 1. Slide lever handle onto spindle until fully seated (Fig. 11A).2. Tighten the set screw securely with 1/8” hex wrench.Step #11 – Install Inside LeverStep #12 – Install and Secure Cylinder1. Slide cylinder through the spring and rosette/collar and screw into lockbody, rotating the cylinder clockwise (Fig. 12A).Cylinder should be flush with rosette/collar.Note: The 43 cylinder may be used when installing this product with or without a gasket.Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 12B). 2. Secure the cylinder by tightening cylinder clamp screw located above the deadbolt using #2 Phillips screwdriver (Fig. 12C).3. Using the key, test cylinder functions: • 8278 Function: Key retracts latch-.• 8276 Function: Key retracts latch and projects and retracts deadbolt-.Fig. 12BPosition cylinder so that the SARGENT logo is right-side up.Correct IncorrectFig. 12AOutside of DoorKeyType 43 CylinderCylinder Clamp Screw#2 Phillips ScrewdriverOutside of DoorFig. 12CFig. 11AInside of DoorSpindle Set ScrewInside Lever
10/15/101-800-810-WIRE • www.sargentlock.com • A7764B 17Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock Step #13 – Attach Front PlateAttach front plate with (2) flat head screws.For 8276- and 8278-function mortise locks with cylinders:1. Insert key into cylinder and rotate.There should be no friction against lock case, wire harness or any other obstructions. Refer to Section 6, Step 8 Wiringif harness friction exists).2. Check that the key retracts the latch: They key should rotate freely.3. Throw the deadbolt:Check that the key retracts both the deadbolt and the latch.4. Try the inside lever:Ensure it retracts latch and deadbolt (if provided).5. Enter a valid PIN code or present a valid iCLASS/PIN credential. This should unlock the outside lever and allow the latch to be retracted.Refer to the Network & Lock Configuration Tool User Manual (WFCD1) for additional information.Operational Check 9Fig. 13AOutside of DoorFront Plate(2) Flat Head ScrewsLock body Screws
SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A7764B-10/10

Navigation menu