ASSALOY SCYICLS1 Microprocessor Controlled Networked Lock User Manual 10 0345 Exhibit Cover

ASSA ABLOY Inc. Microprocessor Controlled Networked Lock 10 0345 Exhibit Cover

Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS1 IC: 6982A-SCYICLS1 FCC Rule Part: 15.247 / 15.225 IC Radio Standards Specification: RSS-210 ACS Project Number: 10-0345 Manufacturer: Assa Abloy Model: N2-IA/IK Manual
A8078A 04/11Copyright 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 with Aperio™ TechnologyMortise LockInstallation Instructionsv.N2
1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/111234567 Table of ContentsWarning ...................................................................................2General Description .................................................................3Specifications ..........................................................................3System Overview .....................................................................3Parts Breakdown .....................................................................4Lock Installation ......................................................................6Operational Check ................................................................14Lock LED Indications ............................................................15Warning: Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment.Warning 1FCC:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiv-er is Connected.• Consult the dealer or an experienced radio/TV technician for help.Industry Canada:This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.8
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 3Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock Warning: SARGENT Mfg. Co. Profile Series v.N2 locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications.System Overview4!To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.SpecificationsGeneral Description23The SARGENT® Profile Series v.N2 lock with Aperio™ Technology makes it easy and cost-effective to bring access control to additional doors. It uses local wireless communication between the lock and an Aperio hub to connect to an access control system, eliminating the greatest cost and inconvenience of traditional access control – the wiring at the door. The Profile Series v.N2 includes HID® iCLASS® 13.56 MHz smart card tech-nology, and all technology features are supported by the physical security of SARGENT ANSI/BHMA Grade 1 hardware.This product is operated by six (6) “AA” alkaline batteries. SARGENT mortise locks are designed with quality components to provide high security, performance and durability.The Aperio mortise lock may be used for both indoor and outdoor applications. A weather-protectivegasket is recommended for outdoor applications.Lock• IEEE 802.15.4 UHF interface• iCLASS technology• AES 128 bit encryptioniCLASS Card Requirements• Supports HID 13.56 MHz iCLASS contactless credentials (full authentication, all formats)• ISO14443 standard memory typesWhen a user presents a supported credential to the lock, the Aperio system is designed to send the credential wirelessly to the Aperio Hub. The Aperio Hub (wired through RS-485 or Wiegand) then communicates with an EAC (Electronic Access Control) system. The EAC system provides the access decision to the Communication Hub where access to the lock is either granted or denied. Access Control PanelAperio Hub Electronic Access Control SystemTCP/IPRS-485/WiegandIEEE 802.15.4 (2.4GHz)
4 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock Parts Breakdown57489991637921091121113151415513.56 MHz iCLASS 5
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 5Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock 1 Outside Lever Reference 8200 Catalog for available levers 12 Inside Lever Reference 8200 Catalog for available levers 13 82-0495 O/S Escutcheon only with Cylinder 182-0493 O/S Escutcheon only without Cylinder 14 82-0492 Inside Escutcheon only without Thumb Turn 182-0494 Inside Escutcheon only with Thumb Turn 15 52-5291 Aperio Electronic Replacement Pack, 13.56 MHz iCLASS 17 52-4340 Battery Cover Assembly 18 01-1212 Security Screw 19 52-2427 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting Screws, Security Allen Wrench)110 Consult Factory Lever Handle Screw (Depends on Lever Style) 111 Consult Factory Inside Adapter Assembly (Depends on Lever Style) 112 Consult Factory Outside Adapter Assembly (Depends On Lever Style) 113 N2-82276-hand-finish Lockbody with Dead Bolt with Cylinder 1N2-82277-hand-finish Lockbody with Dead Bolt without CylinderN2-82278-hand-finish Lockbody with Dead Bolt with CylinderN2-82279-hand-finish Lockbody with Dead Bolt without Cylinder14 82-0084 Faceplate with Dead Bolt (shown) 182-0081 Faceplate without Dead Bolt 115 77-4336 Mortise Screw Pack - Specify Finish (Includes: Wood and Metal Lock body Screws, Faceplate Screws, and Strike Screws)116 Consult Factory #43 Mortise Cylinder 1 ITEM PART NO. DESCRIPTION QTY. Parts Breakdown 13.56 MHz iCLASS (Continued)
6 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock A. Verify Hand and Bevel of DoorStand on outside of locked door when determining door hand.Lock InstallationLH Left Hand Hinges Left Open Inward LHRB Left Hand Reverse Bevel Hinges Left Open Outward RHRight Hand Hinges Right Open Inward RHRB Right Hand Reverse Bevel Hinges Right Open Outward Fig. 1A1 Prepare Door6B. Door PreparationPrior to installation, all holes must be free of burrs, debris and sharp edges. Prepare door according to appropriate template (see website www.intelligentopenings.com):• Wood door: A7457 (ships with product)• Metal door: Template 4533Outside Cylinder Hole(only with cylinder installation)Outside of Door Inside of DoorRibbon Cable Hole (Controller to Keypad, if used)Lever Handle HoleThrough-bolt HoleRibbon Cable Hole (Controller to Keypad)Inside of Lockbody Wire HoleLever Handle HoleThrough-bolt HolePre-drilled and/orTapped HolesMortisedPocketThumb Turn Lever HoleFig. 1BThrough-bolt HoleThrough-bolt Hole
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 7Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock 2 How to Change Hand of Lock bodyBeveled surface of latchbolt must face strike.The deadlatch is self adjusting.To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver approximately 1/4” into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody.Push InRight Hand ShownLocking Guide SlotFig. 2AA. Reverse Lock HandC. Reverse Latch HandFig. 2BB. Retaining RingMake sure the plastic retaining ring is seated correctly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side.2. Orient the modified retaining ring so that the word Bottom is located at the upper portion of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring.Fig. 2C
8 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock 3 Mortise Lock Body DIP Switch Settings Fig. 3A4 Install LockbodyTo install the Lockbody: 1. Feed the wires first through the mortise pocket then feed the wires from the lockbody through the inside door prep for the mortise cutout (Fig. 4A).Note: Connectors and wires must be fed through the non-cylinder side. 2. The wires from the lockbody exit the inside door prep through the mortise cutout.3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws.Note: Do not completely tighten at this time.(2) #12-24 x 1/2” Long Flat Head Screws for Metal Doors(2) #12 x 1-1/4” Long Flat Head Screws for Metal DoorsFig. 4AMortise Connectors Inside of DoorDIP switchNOTE: The DIP switch RX settings located on the rear of the mortise lockbody must be set prior to lock installation. Failure to follow sticker directions will cause inaccurate RX activity to be reported to the access control panel.Set DIP switch for appropriate door application by sliding the DIP switch to the side opposite the red surface of the locking slide.
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 9Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock 5 Exterior Door OptionsA. Fire Stop Plate (P/N 52-0033) B. Weather Conduit (P/N 52-2847)Install weather conduit (part number 52-2847) on NON Fire-Rated exterior doors only (Fig. 5B).1. Carefully insert the weather conduit into the ribbon cable hole on the inside of the door.2. Place the O-ring around the weather conduit on the outside and up against the door (Fig. 5C). Fig. 5AOutside of Door(2) 1/8” Diameter Holes RequiredSlot(2) Self-Tapping #8 x 1/2” Screws for Wood and Metal DoorsFire Stop PlateOutside of DoorFig. 5BFig. 5CFor exterior applications, use weatherseal gasket between escutcheon and outside door surface. To apply weatherseal gasket: 1. Carefully remove the backing from the gasket (Fig. 6A). 2. Apply gasket to escutcheon:a. Starting in one place, press the adhesive side of the gasket firmly against the escutcheon.b. Work around the escutcheon, pressing the sticky side of the gasket firmly against the escutcheon edge.c. The gasket should be aligned so that all edges of the escutcheon are covered.6 Install Gasket (for Exterior Doors) Fig. 6AFire-rated doors require a fire stop plate on the outside of the door (Fig. 5A).1. Drill (2) 1/8” x 1-1/4” deep holes in the door, if not already present.Refer to template for fire-stop prep locations.2. Attach with flap up and out using (2) #8 x 1/2” self-tapping screws for wood and metal doors.
10 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock 8 Install Lock1. With outside lever horizontal, locate the outside escutcheon on the door, while directing the mounting posts through the door and lock body (Fig.8A).Make sure the lever spindle is properly engaged in lock.2. On the inside of the door, insert spindle into the square hole of mortise lock.3. Slide inside adapter and plate assembly over spindle and loosely secure with 2 through-bolt screws (#8-32 x 5/8”).Note: For 82276 and 82278, loosely thread cylinder through escutcheon and into the lock body before tightening the lock case screws and escutcheon through bolts.4. Loosely install the optional cylinder, if present.5. Fully tighten the lock case screws and escutcheon through bolts. 1. Attach escutcheons to the door after the wires are connected.Note: The 43 cylinder may be used with or without a gasket.2A. For fire rated doors: Feed ribbon cable with connector from outside of door through weatherseal gasket and fire stop plate (Fig. 7A). Note: Install ribbon cable with cable exiting down.2B. For non-fire rated doors: Feed ribbon cable with connector from outside of door through weatherseal gasket (if used) and weather conduit. Note: Install ribbon cable with cable exiting down.7 Install Outside EscutcheonFig. 6AOutside of DoorLock Case ScrewsInside of DoorFig. 8A
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 11Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock 9 Inside Escutcheon ConnectionsBefore the controller is attached to the door:1. Connect the cable from the mortise lock to the bottom of the controller assembly (TB1). 2. Attach the reader assembly ribbon cable into the controller assembly (2).Inside of DoorFig. 9AMortise ConnectorReader Ribbon Cable110 Install Inside Esutcheon 1. Gently fold the excess ribbon cable into the ribbon cable hole and mortise and wires into the inside of lock body wire hole, being careful not to pinch wires. 2. Insert (2) #8-32 x 1-1/4” screws through inside escutcheon and thread into outside escutcheon.Straighten escutcheons and tighten securely.Inside of DoorFig. 10A
12 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock Inside of DoorFig. 11BFig. 11A12 Install and Secure CylinderFig. 12AOutside of Door11 Install Inside Lever1. Slide lever handle onto spindle until fully seated (Fig. 11A).2. Tighten the set screw securely with 1/8” hex wrench (Fig. 11B).1. Slide cylinder through the spring and screw into lockbody, rotating the cylinder clockwise (Fig. 12A). Cylinder should be flush with rosette/collar.Note: The 43 cylinder may be used when installing this product with or without a gasket.Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 12B). 2. Secure the cylinder by tightening the cylinder clamp screw located above the deadbolt using a #2 Phillips screwdriver (Fig. 12C).Using the key, test cylinder functions: • 82278 Function: Key retracts latch.• 82276 Function: Key retracts latch and projects and retracts deadbolt.Fig. 12BCorrect Incorrect#2 Phillips ScrewdriverCylinder Clamp ScrewFig. 12C
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 13Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock 13 Attach Front PlateAttach front plate with (2) flat head screws.Fig. 13AOutside of Door14 install or Replace Batteries1. To install or replace batteries, first remove the battery cover (if necessary) using the provided security tool (Fig.14A). 2. Unscrew the bottom screw of the battery keeper and remove the battery keeper, being careful not to break the top tabs holding it in place (Fig.14B). 3. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.4. Replace battery keeper, being careful to engage tabs on the top to hold it in place (Fig. 14B). 5. Attach battery cover to inside escutcheon, making sure to line up tabs with retaining slots in battery cover (Fig. 14C). 6. Secure with the security screw using tool. (Fig. 14A).Fig. 14BFig. 14CTabsRetaining Slots Inside of DoorFig. 14ASecurity Tool (01-029)Battery CoverSecurity ScrewNOTE: Ensure the tamper switch activator does not fall out of the cover during assembly. A tamper event mes-sage will be sent to the EAC panel if tamper is enabled.
14 1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.04/08/11 Profile Series v.N2 Mortise Lock For 82276- and 82278-function mortise locks with cylinders:1. Insert key into cylinder and rotate.There should be no friction against lock case, wire harness or any other obstructions. (Refer to Section -6 Wiring if harness friction exists).2. Check that the key retracts the latch: The key should rotate freely.3. Throw the deadbolt:Check that the key retracts both the deadbolt and the latch.4. Try the inside lever:Ensure it retracts latch and deadbolt (if provided).5. Present a valid iCLASS credential to un-lock outside lever and retract latch. Operational Check 7
04/08/111-800-810-WIRE • www.sargentlock.com • A8078A 15Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.N2 Mortise Lock The lock has three LEDs that support an optical scheme with red, yellow and green. The indication scheme is described by the figures below:Card read (configurable) Access granted, EAC offline or onlineAccess denied, EAC online Access denied, EAC offline Lock mechanism is blocked when closingError in lock, maintenance required Time to replace the battery Battery reached end of life, lock disabledOne yellow flash (.25 second) One green flash (1 second) One red flash (1 second) Three red flashes (.5 s each) Fig. Lock Normal operation LED indicationLock LED Indications8NOTE: When the lock mechanism is blocked (lock jammed) the knob must be turned to release it. The “Error in lock” indication is also shown instead of the POST flashes if the battery is not accepted as new after a power¬on¬reset.1 Lock Normal Operation LED indication2 Lock Maintenence LED Indication Some special LED indication schemes are used during lock maintenance actions:Enter configuration mode Five yellow flashes (.125 s each)Fig. Lock maintenance LED indication Continuous red flashes blocked when closing (.125 seconds every 1 second) Ten red flashes (.125 s each), maintenance required; repeated if lock can’t close Continuous yellow flashes (.25 seconds every 5 seconds) Continuous red flashes of life, (.25 seconds every 5 seconds)
SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A8078A - 04/113 Lock Self Test LED IndicationAfter replacing the battery, a Power On Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as is described by the figure below:One red, one green flash (1 second each) One red flash followed by 16 red or green flashes (.5 s each)Fig. Lock POST LED indicationThe first flash is always red. If the POST fail, the color of the 16 trailing flashes indicate the status of each individual test as described by the following table: Blink Meaning if Red Code in Event Log2 Main board firmware corrupt 0x0001 3 Override list corrupt 0x00024 Production data corrupt 0x00045 Security data corrupt 0x00086 Configuration data corrupt 0x00107 Battery power low 0x00208 RFID reader circuit error 0x00409 Voltage regulator error 0x008010 Card detection circuit error 0x010011 Secure area communication error 0x020012 Secure area memory corrupt 0x040013 Secure area sensor or motor error 0x080014 Radio modem communication error 0x100015 Radio modem memory corrupt 0x200016 Radio modem configuration error 0x400017 Radio modem RF circuit error 0x8000NOTE: If the battery is not accepted as new after a power on reset, no POST is performed. Instead, the 10 quick red flashes used to indicate Error in lock is shown.

Navigation menu