ASUSTeK Computer AAM6KBDBX WIRELESS ADSL 2+ BONDED CPE User Manual Paradyne Bonded Channel

ASUSTeK Computer Inc WIRELESS ADSL 2+ BONDED CPE Paradyne Bonded Channel

Contents

users manual 1

Zhone Bonded Channel User Manual Version 1.1 Version Date: February 16, 2007 Document #: BD-ZU0007-11
FCC Warning Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: －Reorient or relocate the receiving antenna. －Increase the separation between the equipment and receiver. －Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. －Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Prohibition of Co-location This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter Safety Information To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Declaration of Conformity for R&TTE directive 1999/5/EC Essential requirements – Article 3 Protection requirements for health and safety – Article 3.1a Testing for electric safety according to , EN50392 and EN 60950-1 has been conducted. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility – Article 3.1b Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-17 has been conducted. These are considered relevant and sufficient. Effective use of the radio spectrum – Article 3.2 Testing for radio test suites according to EN 300 328 has been conducted. These are considered relevant and sufficient. CE Mark Warning This is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
2 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 Table of Contents GENERAL INFORMATION.......................................................................... 4 Package Contents ........................................................................ 4 Important Safety Instructions.......................................................... 4 Front Panel View......................................................................... 5 Back Panel View.......................................................................... 6 INSTALLING THE ROUTER......................................................................... 7 Connect the ADSL Line and Telephone ............................................... 7 Connect the PC to the Router ......................................................... 7 Connect the Power Adapter............................................................ 7 INSTALLATION DIAGRAM.......................................................................... 8 MOUNTING THE UNIT ............................................................................ 9 CONFIGURING YOUR COMPUTER ................................................................10 Windows 2000............................................................................10 Windows XP ..............................................................................11 LOG IN TO THE ROUTER.........................................................................12 DEVICE INFO....................................................................................13 Summary..................................................................................13 WAN .......................................................................................14 STATISTICS ...............................................................................15 LAN Statistics.........................................................................15 WAN Statistics........................................................................15 ATM Statistics ........................................................................16 ADSL Statistics .......................................................................17 ADSL BER Test........................................................................17 Route......................................................................................19 ARP (Address Resolution Protocol)...................................................19 DHCP (Dynamic Host Configuration Protocol)......................................20 QUICK SETUP ...................................................................................21 ATM PVC Configuration .............................................................21 ADVANCED SETUP...............................................................................26 WAN .......................................................................................26 Connection Type.....................................................................27 LAN Local Area Network (LAN) Setup................................................32 NAT........................................................................................33 Virtual Servers .......................................................................33 Port Triggering.......................................................................35 DMZ Host..............................................................................36 Firewall...................................................................................37 IP Filtering—Outgoing...............................................................37 IP Filtering—Incoming...............................................................38 MAC Filtering.........................................................................39 Parental Control .....................................................................40 Quality of Service.......................................................................41 Queue Config.........................................................................42 QoS Classification....................................................................42 Routing ...................................................................................44 Default Gateway.....................................................................44 Static Route ..........................................................................45 RIP .....................................................................................46 DNS ........................................................................................46 DNS Server............................................................................46 Dynamic DNS .........................................................................47 ADSL.......................................................................................48 DSL Advanced Settings..............................................................49
3 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 Tone Settings.........................................................................50 Port Mapping.............................................................................51 WIRELESS.......................................................................................53 Basic.......................................................................................53 Security...................................................................................53 MAC Filter................................................................................55 Wireless Bridge..........................................................................56 Advanced .................................................................................56 Quality of Service.......................................................................58 Station Info ..............................................................................59 TROUBLESHOOTING—DIAGNOSTICS..............................................................59 MANAGEMENT ..................................................................................60 Settings...................................................................................60 Backup Settings......................................................................60 Update Settings......................................................................61 Restore Default ......................................................................61 System Log ...............................................................................62 System Log – Configuration ........................................................63 Internet Time............................................................................63 Access Control...........................................................................64 Services ...............................................................................64 IP Addresses ..........................................................................65 Passwords.............................................................................66 Update Software ........................................................................66 Save / Reboot............................................................................67
General Information The Bonded Channel features 4 LAN ports and wireless ability. Package Contents The package includes one of each of the following items— • Bonded Channel • 12 VDC 1.5 A power adapter • RJ-11 telephone cable • RJ-45 Ethernet cable • External antenna • User Manual / Quick Guide Important Safety Instructions • Place your device on a flat surface close to the cables in a location with sufficient ventilation. • To prevent overheating, do not obstruct the ventilation openings of this equipment. • Plug this equipment into a surge protector to reduce the risk of damage from power surges and lightning strikes. • Operate this equipment only from an electrical outlet with the correct power source as indicated on the adapter. • Do not open the cover of this equipment. Opening the cover will void any warranties on the equipment. • Unplug equipment first before cleaning. A damp cloth can be used to clean the equipment. Do not use liquid / aerosol cleaners or magnetic / static cleaning devices. 4 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Front Panel View LED 5 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 Mode Definition Solid (green) IP is connected and no traffic detected. Modem is in bridged mode or ADSL connection not present. No light Blinking Connected and traffic is present. Internet Red Device attempted to connect to IP and failed. Solid Wireless is enabled. No light Wireless is disabled. AP Blinking There is wireless traffic. Solid ADSL is connected, and there is no ADSL traffic. No light ADSL is not connected. DSL2 ACT Blinking There is ADSL traffic. Solid ADSL is connected, and there is no ADSL traffic. No light ADSL is not connected. DSL1 ACT Blinking There is ADSL traffic. Solid Router is connected to the LAN. No light No connection to the LAN. Check if the LAN cable is connected to the router. LAN1-LAN4 Blinking LAN traffic Solid Router is powered on. Power Router is not powered. Check if the router is plugged in and if the power switch is turned on. No light
Back Panel View Port Description RJ-11 cable connects to telephone (no external splitter necessary; unit has internal splitter). Phone Line RJ-11 cable connects the ADSL line. Reset / Default Restart—press the button for less than 5 seconds. Default settings—press the button for 5 seconds or longer. RJ-45 connects the unit to Ethernet devices such as a PC or a switch. LAN1-LAN4 Power Connects to the 12 VDC 1.5 A power adapter. Antenna Transmits wireless signals 6 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
7 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 Installing the Router Connect the ADSL Line and Telephone Connect one end of an RJ-11 cable from your ADSL connection and the other end to the LINE port of the router. Use a second RJ-11 cable to connect between a telephone and the PHONE port of the router. Connect the PC to the Router Use the Ethernet cable to connect your computer directly to the router. Connect one end of the Ethernet cable to one of the 4 ports labeled LAN on the rear panel of the router and connect the other end to the Ethernet port of your computer. Attach any additional PCs to the router using RJ-45 cables to the port labeled LAN on the rear panel of the router. Connect the Power Adapter Complete the process by connecting the AC power adapter to the POWER connector on the back of the device and plug the adapter into a wall outlet or power strip. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them.
Installation Diagram 8 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Mounting the Unit The bonded channel unit can be mounted on the wall with the screws provided. Mounting can be done on wall material including concrete, wood, or drywall. Select an appropriate location free from obstructions or any possible interference. Make sure the cables can be easily attached to the router without strain. The illustration below shows how to mount the device horizontally on a wall. 9 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
10 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 Configuring Your Computer Prior to accessing the router through the LAN port, note the following necessary configurations— • Your PC’s TCP/IP address: 192.168.1.__( the last number is any number between 2 and 254) • The router’s default IP address: 192.168.1.1 • Subnet mask: 255.255.255.0 Below are the procedures for configuring your computer. Follow the instructions for the operating system that you are using. Windows 2000 1. In the Windows taskbar, click on the Start button and point to Settings, Control Panel, and Network and Dial-up Connections (in that order). 2. Click on Local Area Connection. When you have the Local Area Connection Status window open, click on Properties. 3. Listed in the window are the installed network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled, and you can skip to Step 10. 4. If Internet Protocol (TCP/IP) does not appear as an installed component, then click on Install. 5. In the Select Network Component Type window, click on protocol and then the Add button. 6. Select Internet Protocol (TCP/IP) from the list and then click on OK. 7. If prompted to restart your computer with the new settings, click OK. 8. After your computer restarts, click on the Network and Dial-up Connections icon again, and right click on the Local Area Connection icon and then select Properties. 9. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP) and then click on Properties. 10. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled Use the following IP address and type 192.168.1.x (where x is any number between 2 and 254) and 255.255.255.0 in the IP address field and Subnet Mask field.
11 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 11. Click on OK twice to save your changes and then close the Control Panel. Windows XP 1. In the Windows taskbar, click on the Start button and point to Settings and then click Network Connections. 2. In the Network Connections window, right click on the Local Area Connection icon and click on properties. 3. Listed in the Local Area Connection window are the installed network components. Make sure the box for Internet Protocol (TCP/IP) is checked and then click on Properties. 4. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled Use the following IP address and type 192.168.1.x (where x is any number between 2 and 254) and 255.255.255.0 in the IP address field and Subnet Mask field. 5. Click on OK twice to save your changes and then close the Control Panel.
Log in to the Router This section explains how to log in to your router using the following steps— 1. Launch your web browser. 2. Enter the URL http://192.168.1.1 in the address bar and click on Enter. A login screen like the one below will be displayed after you connect to the user interface. 3. Enter your user name and password, and then click on OK to display the user interface. NOTE: There are two default user name and password combinations— Username Password Access to (in interface) admin admin All sections user user All sections except Advanced and Wireless The admin / admin combination can perform all functions. The user / user name and password combination can display device status, but cannot change or save configurations. Passwords can be changed at any time. 12 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Device Info This section describes the system information that can be accessed using the menu items under Device Info. In addition to general device information, the following items can also be seen—WAN, Statistics, Route, ARP and DHCP. Summary To access information on the device and connection status, click on Summary under Device Info. It shows the following information about the CPE—  Board ID  Software Version  Bootloader (CFE) Version  Wireless Driver Version  MAC Address  Upstream / Downstream Line Rate (in Kbps)  LAN IP Address  Default Gateway  Primary DNS Server IP Address  Secondary DNS Server IP Address 13 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
WAN To access WAN Information click on the WAN item located under Device Info. The following information about each WAN connection is provided—  VPI/VCI  Connection ID  Category  Service Name  Interface Name  Protocol  IGMP (Internet Group Management Protocol)  QoS (Quality of Service)  State  Status  IP Address Note that this screen will be like the one below before a WAN connection is set up. The following screen shows a WAN connection that has been created. 14 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
STATISTICS LAN Statistics To access LAN statistics click on the LAN item under Statistics. Information is given for each interface (Ethernet Bonding, Ethernet (Port 1-4) and Wireless). For both received and transmitted data, the following information is provided—  Bytes  Packets  Errors  Drops To renew the data, click on the Reset Statistics button below the table. WAN Statistics To access WAN statistics click on the WAN item under Statistics. WAN statistics, like the LAN statistics are listed by each connection with received and transmitted data packet information. 15 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
ATM Statistics To access ATM statistics click on the ATM item under Statistics. ATM statistics are organized into three areas— ATM Interface Statistics, AAL5 Interface Statistics, and AAL5 VCC Statistics. To view renewed values, click on the Reset Statistics button. 16 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
ADSL Statistics To view ADSL statistics click on the ADSL item under Statistics. Information contained in this screen is useful for troubleshooting and diagnostics of connection problems. Click on the Reset Statistics button to view renewed values. ADSL BER Test A Bit Error Rate Test (BER Test) is a test that reflects the ratio of error bits to the total number transmitted. If you click on the ADSL BER Test button at the bottom of the ADSL Statistics page, the following pop-up screen will appear allowing you to set the tested time and to begin the test. 17 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Below is an ADSL BER Test result screen displaying information about the test including the error bits and ratio. 18 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Route To access the routing information, click on the Route item under Device Info. The following are the routing information provided—  Destination  Gateway  Subnet Mask  Flag  Metric  Service  Interface ARP (Address Resolution Protocol) To access ARP status click on the ARP item under Device Info. The information provided shows the IP address that is mapped to the hardware IP address. 19 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
DHCP (Dynamic Host Configuration Protocol) To access the DHCP lease information click on DHCP under Device Info. Devices that have been issued IP addresses by DHCP will be listed on this screen by its hostname, MAC address and IP address along with the expiration of the IP address. 20 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Quick Setup This section will explain how to quickly configure the router for the main purpose of connecting to the Internet. If you need to configure any advanced functions, then those can be performed in the advanced section. ATM PVC Configuration To enable the auto-connect process, click on the box labeled DSL Auto-connect, a process that will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To continue, click on the Next button. Note: The following example will be a PPPoA example where the VPI / VCI numbers have not been used. Note that the same numbers can be used only once. 21 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
VPI and VCI numbers can be entered manually if you do not want to use DSL Auto-connect. Quality of service can also be enabled on this screen. Additionally, if you do not use DSL Auto-connect, then you will need to select the connection type and encapsulation mode from a list as shown below. 22 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
The next screen to appear will depend on the connection type that was selected in the previous screen. In the next screen, decide whether or not NAT, firewall, IGMP multicast, and WAN service should be enabled. 23 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
The following is the Device Setup screen where you enter the IP address / subnet mask as well as enable or disable DHCP server. If you have a second IP address and subnet mask for the LAN interface, click on the checkbox. The last screen under the Quick Start section allows you to set up the wireless feature on the router. 24 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
When you click on Next, the summary screen shows the settings made under WAN setup. 25 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Advanced Setup This section of the user manual explains the advanced configurations of the CPE. The topics under Advanced Setup are WAN, LAN, NAT, security, routing, DNS, and DSL. WAN Configure the WAN settings according to the instructions given by your ISP. Each existing WAN connection will be listed in the table with the options to edit or remove them as well as to add new WAN connections. Remember to click on the Save / Reboot button after any changes made. Click on the Add button if you want to add a new rule for the WAN interface. The ATM PVC Configuration screen appears. 26 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
27 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11 The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. Verify the following values with your ISP before you change them. • VPI: Virtual Path Identifier. The valid range is 0 to 255. • VCI: Virtual Channel Identifier. The valid range is 32 to 65535. • Service Category: Five classes of traffic are listed— o UBR Without PCR o UBR With PCR o CBR o Non Realtime VBR o Realtime VBR Enabling QoS for a PVC improves performance for selected classes of applications. However, since QoS also consumes system resources, the number of PVCs is reduced. If you want to enable QoS service, click on the Enable Quality Of Service check box. Connection Type This screen shows the below types of network protocols and encapsulation modes— • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • MAC Encapsulation Routing (MER) • IP over ATM (IpoA) • Bridging Select the mode that your ISP has instructed you to use and click on Next. Also available is the option to enable 802.1q, a standard to allow multiple bridged networks to transparently share the same physical network link without leakage of information between networks (i.e. "trunking"). Click on the checkbox if you wish to enable this function.
If you selected a PPP connection, then the next screen shows the PPP Username and Password section. The PPP username and password will have already been entered. For this example, the PPPoA Service Name “Test” has been chosen. Select an authentication method from the following choices— auto, PAP, CHAP, and MSCHAP. Dial on demand: If you select this box, then an additional Inactivity Timeout box will appear for you to enter the time in minutes. PPP IP extension is a special feature deployed by some service providers. Do not select this item unless specifically required by your service provider. Click on the Next button when you finish to continue. 28 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
The next screen allows you to configure NAT settings as well as enable IGMP multicast and WAN service. Bridge Example: To set up a bridge connection, from the following Connection Type Screen, select bridging as the connection type and select the preferred encapsulation mode and then click on Next. 29 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
The next screen will be to select whether or not to enable bridge service and to enter the service name. To finish the bridge connection setup, click on Next and the summary of the connection will be displayed. 30 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
When the settings are complete, the next screen shows a WAN Setup – Summary screen displaying the WAN configurations made. Below is the bridge connection WAN Setup Summary page. Click on the Save button when the settings are correct. The below screen will appear showing the WAN settings that you made. When satisfied with the settings, and no changes are necessary, click on the Finish button. To remove any settings, click on the Remove button. 31 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
After selecting the Finish button, the below screen will appear. At this point, the router will reboot to save the changes made. LAN Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond your LAN’s IP Subnet. Enter the following items—  IP Address  Subnet Mask  Enable UpnP  Disable / Enable DHCP Server  Start / End IP Address  Leased Time in hours  Configure the second IP address and Subnet Mask for LAN interface The Save button only saves the LAN configuration data, but does not apply the configurations. Select the Save/Reboot button to save the LAN configuration data and reboot the router and apply the new configurations. 32 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
NAT Enable NAT (Network Address Translation) to configure the Virtual Server, Port Triggering, and DMZ Host. Virtual Servers A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. To set up a virtual server, click on the Add button. Select the virtual server from the drop-down list and complete the server IP address, then click on the Save / Apply button. 33 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
The following screen appears after you save your selection. To add additional virtual servers, click on the Add button. If you need to remove any of the server names, select the check box and click on the Remove button. 34 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Port Triggering Click on the Add button to add Port Triggering to your Internet application. The below screen appears when you click on Add allowing you to select the application that you want to set the port settings for. After a selection has been made, click on the Save / Apply button. The below screen appears after you save your selections. You will be able to add or remove selections made, by clicking on the Add and Remove buttons. 35 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save / Apply. 36 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Firewall IP Filtering—Outgoing The outgoing filter will block the LAN traffic from entering the WAN side. Click on the Add button to create filters. The below screen will appear when you click on Add. Input the filter name, source information (from the LAN side), and destination information (from the WAN side). Then click on Save / Apply. 37 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
IP Filtering—Incoming Incoming filter filters the WAN traffic to the LAN side. Click on the Add button to add incoming filter settings. Enter a filter name, information about the source address (from the WAN side), and information about the destination address (to the LAN side). Select the protocol and WAN interface, and then click on Save/Apply to add the setting. 38 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. If you click on Change Policy, a confirmation dialog allows you to verify your change. If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save / Apply to save it. 39 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
After you save the settings, a screen showing the settings will appear. On this screen you will be able to view and delete MAC filtering rules. Parental Control In a home setting, parents can also restrict the day of the week certain computers can access the router. Click on Add to set up the restrictions. After you click on Add, you will see the below screen. You will be able to enter the MAC address of the PC that you wish to place on a time of day restriction. Click on Save / Apply to save the settings and to continue. 40 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11
Quality of Service This QoS screen allows you to enable QoS and configure outgoing IP packet traffic management using DSCP (Differentiated Services Code Point) marks. Any outgoing packets without any classification rules will be marked with the DSCP mark that is selected. 41 Zhone Bonded Channel User Manual Version 1.1 Document #: BD-ZU0007-11

Navigation menu