ASUSTeK Computer ER-C2I receiver User Manual FCC IC
ASUSTeK Computer Inc receiver FCC IC
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1099447 |
| Application ID | aZFExkoQsRbQqMn/4u8LTQ== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 3.32kB (41453 bits) |
| Date Submitted | 2009-04-21 00:00:00 |
| Date Available | 2009-05-01 00:00:00 |
| Creation Date | 2009-04-15 17:53:20 |
| Producing Software | pdfFactory Pro 3.10 (Windows XP Professional Chinese) |
| Document Lastmod | 2009-04-15 18:17:02 |
| Document Title | User Manual-FCC IC.doc |
| Document Creator | pdfFactory Pro www.ahasoft.com.tw/FinePrint |
| Document Author: | betty |
User Manual Getting Start 1. Thanks for purchasing this product This product used the latest wireless 2.4GHz solution and the most advanced optical sensor to detect the cursor movement, position and rapid. Especially receiver is build-in design for Asus PC system. 2.System Requirement： IBM PC compatible. 3. Important information Before you use this product, please read the user manual in this product to avoid and reduce the operating harm of your wrist. This receiver is completely meet the international safety requirement. Please use this product from 0 degree to 40 degrees in Celsius (F32-F104 degrees). Please do not disassemble the receiver yourself or might cause you in danger. 4. Connection 1. Ensure the receiver is tightened on pc system by screws. (H1,H2) 2. Ensure C1 is connected to pc USB interface port. 5. C1 connector Pin Description Pin No. Signal Name Type 1. DM I/O USB Bus 2. DP I/O USB Bus 3. GND GND 4. NC Open (N.C.) 5. Vbus 5 V power FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to Part 15 the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: MSQER-C2I”. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual for the end product which integrates this module. The users manual for OEM integrators must include the following information in a prominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Canada-Industry Canada (IC) STATEMENT This device complies with RSS-210 of the Industry Canada rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This device is intended only for OEM integrators under the following conditions: 1)The antenna must be installed such that 20cm is maintained between the antenna and users. 2)The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 3568A-ERC2I”. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual for the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res XMP Toolkit : 3.1-701 Create Date : 2009:04:15 17:53:20+08:00 Creator Tool : pdfFactory Pro www.ahasoft.com.tw/FinePrint Modify Date : 2009:04:15 18:17:02+08:00 Metadata Date : 2009:04:15 18:17:02+08:00 Format : application/pdf Creator : betty Title : User Manual-FCC IC.doc Producer : pdfFactory Pro 3.10 (Windows XP Professional Chinese) Document ID : uuid:40ede525-cfac-4e89-9661-866e2023b0eb Instance ID : uuid:ff01842d-ff94-42be-b6a7-d1e3bcfaecbe Page Count : 3 Author : bettyEXIF Metadata provided by EXIF.tools