ASUSTeK Computer RTGZ00 Wireless-AC5300 Tri-band Gigabit Router User Manual

ASUSTeK Computer Inc Wireless-AC5300 Tri-band Gigabit Router

User Manual

RT-AC5300User GuideWireless-AC 5300 Tri-Band Gigabit Router
2Copyright © 2014 ASUSTeK Computer Inc. All Rights Reserved.No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. (“ASUS”).Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. E9670First EditionDecember 2014
3Table of contents1 Getting to know your wireless router1.1 Welcome! ........................................................................................71.2 Package contents .........................................................................71.3 Your wireless router .....................................................................81.4 Positioning your router ........................................................... 101.5 Setup Requirements ................................................................ 111.6 Router Setup ............................................................................... 121.6.1 Wired connection ..................................................................121.6.2 Wireless connection ............................................................. 132 Getting started2.1 Logging into the Web GUI ..................................................... 152.2 Setting up your router using the Quick Internet Setup - Smart Connect Wizard ............... 162.3 Connecting to your wireless network ................................ 183 Configuring the General settings3.1 Using the Network Map ......................................................... 193.1.1 Setting up the wireless security settings ......................203.1.2 Managing your network clients ....................................... 223.1.3 Monitoring your USB device .............................................233.2 Creating a Guest Network ...................................................... 263.3 AiProtection ................................................................................ 283.3.1 Network Protection .............................................................. 293.3.2 Setting up Parental Controls ............................................. 333.4 Adaptive QoS .............................................................................. 373.4.1 Bandwidth Monitor ..............................................................373.4.2 QoS ............................................................................................. 383.4.3 Web History .............................................................................393.4.4 Traffic Monitor ........................................................................40
4Table of contents3.5 Using the USB Application ..................................................... 413.5.1 Using AiDisk ............................................................................... 413.5.2 Using Servers Center ............................................................433.5.3 3G/4G ........................................................................................483.6 Using AiCloud 2.0 ...................................................................... 493.6.1 Cloud Disk ................................................................................503.6.2 Smart Access ........................................................................... 523.6.3 Smart Sync ............................................................................... 534 Configuring the Advanced Settings4.1 Wireless ......................................................................................... 544.1.1 General ......................................................................................544.1.2 WPS ............................................................................................574.1.3 Wireless MAC Filter ...............................................................614.1.4 RADIUS Setting ......................................................................624.1.5 Professional .............................................................................634.2 LAN ................................................................................................. 654.2.1 LAN IP ........................................................................................654.2.2 DHCP Server ............................................................................664.2.3 Route .........................................................................................684.2.4 IPTV ............................................................................................... 694.3 WAN ............................................................................................... 704.3.1 Internet Connection .............................................................704.3.2 Dual WAN .................................................................................734.3.3 Port Trigger .............................................................................. 744.3.4 Virtual Server/Port Forwarding ........................................764.3.4 DMZ............................................................................................794.3.5 DDNS .........................................................................................804.3.6 NAT Passthrough ...................................................................81
5Table of contents4.4 IPv6 ................................................................................................. 824.5 VPN Server ................................................................................... 834.6 Firewall .......................................................................................... 844.6.1 General ......................................................................................844.6.2 URL Filter ..................................................................................844.6.3 Keyword filter .........................................................................854.6.4 Network Services Filter .......................................................864.6.5 IPv6 Firewall ............................................................................874.7 Administration ........................................................................... 884.7.1 Operation Mode ....................................................................884.7.2 System ....................................................................................... 894.7.3 Firmware Upgrade ................................................................ 904.7.4 Restore/Save/Upload Setting ...........................................914.8 System Log .................................................................................. 925 Utilities5.1 Device Discovery ....................................................................... 935.2 Firmware Restoration .............................................................. 945.3 Setting up your printer server .............................................. 955.3.1 ASUS EZ Printer Sharing .....................................................955.3.2 Using LPR to Share Printer .................................................99 5.4 Download Master ....................................................................1045.4.1 Configuring Bit Torrent download settings .............. 1055.4.2 NZB settings ......................................................................... 1066 Troubleshooting 1076.1 Basic Troubleshooting ........................................................... 1076.2 Frequently Asked Questions (FAQs) ................................110
6AppendicesNotices 120ASUS Contact information ..................................................................135Networks Global Hotline Information.............................................136
71 Getting to know your wireless router1.1 Welcome!Thank you for purchasing an ASUS RT-AC5300 Wireless Router!The ultra-thin and stylish RT-AC5300 features 2.4GHz, 5GHz-1, and 5GHz-2 triple bands for an unmatched concurrent wireless HD streaming; SMB server, UPnP AV server, and FTP server for 24/7 file sharing; a capability to handle 300,000 sessions; and the ASUS Green Network Technology, which provides up to 70% power-saving solution.1.2 Package contentsNOTES:• If any of the items are damaged or missing, contact ASUS for technical inquiries and support, Refer to the ASUS Support Hotline list at the back of this user manual.• Keep the original packaging material in case you would need future warranty services such as repair or replacement.RT-AC5300 Wireless Router AC adapterNetwork cable (RJ-45) Quick Start GuideSupport CD (Manual)
81.3 Your wireless routerLED On/O buttonPress this button to turn on/o the backlight LED on the panel.Wi-Fi On/O buttonPress this button to turn on /o the Wi-Fi connection. Power LED O: No power. On: Device is ready. Flashing slow: Rescue mode2.4GHz LED / 5GHz LED O: No 2.4GHz or 5GHz signal. On: Wireless system is ready. Flashing: Transmitting or receiving data via wireless connection.LAN 1~4 LED O: No power or no physical connection. On: Has physical connection to a local area network (LAN).WAN (Internet) LED Red: No IP or no physical connection. On: Has physical connection to a wide area network (WAN).WPS LED O: WPS verication process is o or completed. Flashing: WPS verication process is activated.USB 3.0 portInsert USB 3.0 devices such as USB hard disks or USB ash drives into this port.
9NOTES: • Useonlytheadapterthatcamewithyourpackage.Usingotheradapters may damage the device.• Specifications: DC Power adapter DC Output: +19V with max 2.37A currentOperating Temperature 0~40oCStorage 0~70oCOperating Humidity 50~90% Storage 20~90% USB 2.0 portInsert USB 2.0 devices such as USB hard disks or USB flash drives into this port.WPS buttonThis button launches the WPS Wizard. Reset buttonThis button resets or restores the system to its factory default settings.WAN (Internet) portConnect a network cable into this port to establish WAN connection. LAN 1 ~ 4 portsConnect network cables into these ports to establish LAN connection.Power buttonPress this button to power on or off the stystem. Power (DC-IN) portInsert the bundled AC adapter into this port and connect your router to a power source.
101.4 Positioning your routerFor the best wireless signal transmission between the wireless router and the network devices connected to it, ensure that you:• Place the wireless router in a centralized area for a maximum wireless coverage for the network devices.• Keep the device away from metal obstructions and away from direct sunlight.• Keep the device away from 802.11g or 20MHz only Wi-Fi devices, 2.4GHz computer peripherals, Bluetooth devices, cordless phones, transformers, heavy-duty motors, uorescent lights, microwave ovens, refrigerators, and other industrial equipment to prevent signal interference or loss.• Always update to the latest rmware. Visit the ASUS website at http://www.asus.com to get the latest rmware updates.• To ensure the best wireless signal, orient the six detachable antennas as shown in the drawing below.
111.5 Setup RequirementsTo set up your wireless network, you need a computer that meets the following system requirements:• EthernetRJ-45(LAN)port(10Base-T/100Base-TX/1000BaseTX)• IEEE802.11a/b/g/n/acwirelesscapability• AninstalledTCP/IPservice• WebbrowsersuchasInternetExplorer,Firefox,Safari,orGoogle ChromeNOTES: • Ifyourcomputerdoesnothavebuilt-inwirelesscapabilities,youmayinstall an IEEE 802.11a/b/g/n/ac WLAN adapter to your computer to connect to the network.• Withitstri-bandtechnology,yourwirelessroutersupports2.4GHz,5GHz-1, and 5GHz-2 wireless signals simultaneously. This allows you to do Internet-related activities such as Internet surfing or reading/writing e-mail messages using the 2.4GHz band while simultaneously streaming high-definition audio/video files such as movies or music using the 5GHz-1 and 5GHz-2 bands.• SomeIEEE802.11ndevicesthatyouwanttoconnecttoyournetworkmay or may not support 5GHz band. Refer to the device's manual for specifications.• TheEthernetRJ-45cablesthatwillbeusedtoconnectthenetworkdevices should not exceed 100 meters.
121.6 Router SetupIMPORTANT!• Use a wired connection when setting up your wireless router to avoid possible setup problems.• Before setting up your ASUS wireless router, do the following: • If you are replacing an existing router, disconnect it from your network. • Disconnect the cables/wires from your existing modem setup. If your modem has a backup battery, remove it as well. • Reboot your cable modem and computer (recommended).1.6.1 Wired connectionNOTE: You can use either a straight-through cable or a crossover cable for wired connection.To set up your wireless router via wired connection:1. Insert your wireless router’s AC adapter to the DC-IN port and plug it to a power outlet.ComputerWall Power OutletModemPowerWAN LAN
132. Using the bundled network cable, connect your computer to your wireless router’s LAN port.IMPORTANT! Ensure that the LAN LED is blinking.3 Using another network cable, connect your modem to your wireless router’s WAN port.4. Insert your modem’s AC adapter to the DC-IN port and plug it to a power outlet.1.6.2 Wireless connectionTo set up your wireless router via wireless connection:1. Insert your wireless router’s AC adapter to the DC-IN port and plug it to a power outlet.2 Using the bundled network cable, connect your modem to your wireless router’s WAN port.ComputerWall Power OutletModemPowerWAN
143. Insert your modem’s AC adapter to the DC-IN port and plug it to a power outlet.4. Install an IEEE 802.11a/b/g/n/ac WLAN adapter on your computer.NOTES: • Fordetailsonconnectingtoawirelessnetwork,refertotheWLANadapter’s user manual.• Tosetupthesecuritysettingsforyournetwork,refertothesectionSetting up the wireless security settings in Chapter 3 of this user manual.
152 Getting started2.1 Logging into the Web GUIYour ASUS wireless router comes with an intuitive web graphical user interface (GUI) that allows you to easily configure its various features through a web browser such as Internet Explorer, Firefox, Safari, or Google Chrome.NOTE: The features may vary with different firmware versions.To log into the web GUI:1. On your web browser, manually key in the wireless router’s default IP address: 192.168.1.1 or enter http://router.asus.com.2. On the login page, key in the default user name (admin) and password (admin).3. You can now use the Web GUI to configure various settings of your ASUS Wireless Router.NOTE: If you are logging into the Web GUI for the first time, you will be directed to the Quick Internet Setup (QIS) page automatically.Navigation panel QIS - Smart Connect Wizard Top command buttonsInformation bannermiddle columnright column
162.2 Setting up your router using the Quick Internet Setup - Smart Connect WizardThe Quick Internet Setup (QIS) Smart Connect Wizard automatically connects your clients in your network to the appropriate band (2.4GHz, 5GHz-1, or 5GHz-2 ) for optimal speed.To set up your router using QIS - Smart Connect Wizard:1. Press the power button at the back of your router. Ensure that the Power, LAN and WAN LEDs are on.2. Launch your web browser such as Internet Explorer, Firefox, Google Chrome, or Safari.NOTE: If the QIS-Smart Connect Wizard does not launch automatically, enter http://192.168.1.1 or http://router.asus.com in the address bar and refresh the browser again.3. The wireless router’s Quick Internet Setup (QIS) feature automatically detects if your ISP connection type is Dynamic IP, PPPoE, PPTP, L2TP, and Static IP. If your connection type is Dynamic IP (DHCP), QIS wizard will automatically direct you to the next step. NOTE: If your connection type is Static IP, choose Static IP and click Next. Key in IP address, subnet mask, default gateway and DNS server information provided by your ISP. Click Next to proceed.4. Key in the username and password for your Internet connection type that you obtained from your Internet Service Provider (ISP).
175. Click Next. Wait until your router redetects your Internet connection type and the Smart Connect screen appears.6. Click Next to go to the setup page.7. Select any of these two Smart Connect options: • Tri-band Smart Connect: Select this option if you want to enable Smart Connect for 2.4GHz, 5GHz-1, and 5GHz-2 frequency bands at the same time, and automatically connect your devices in your network to the best band for optimal speed. • Standard Setup: Select this option if you want to set up three bands independently. Smart Connect is disabled under this option.8. Assign the network name (SSID) and security key for your selected Smart Connect wireless connection.9. Click Apply and wait until the Smart Connect process is completed.
182.3 Connecting to your wireless networkAfter setting up your wireless router via QIS, you can connect your computer or other smart devices to your wireless network.To connect to your network:1. On your computer, click the network icon in the notification area to display the available wireless networks.2. Select the wireless network that you want to connect to, then click Connect.3. You may need to key in the network security key for a secured wireless network, then click OK.4. Wait while your computer establishes connection to the wireless network successfully. The connection status is displayed and the network icon displays the connected status.NOTES: • Refertothenextchaptersformoredetailsonconfiguringyourwireless network's settings.• Refertoyourdevice'susermanualformoredetailsonconnectingitto your wireless network.
193 Configuring the General settings3.1 Using the Network Map Network Map allows you to configure your network’s security settings, manage your network clients, and monitor your USB device.
203.1.1 Setting up the wireless security settingsTo protect your wireless network from unauthorized access, you need to configure its security settings.To set up the wireless security settings:1. From the navigation panel, go to General > Network Map.2. OntheNetworkMapscreenandunderSystem status, you can configure the wireless security settings such as SSID, security level, and encryption settings.NOTE: You can set up different wireless security settings for 2.4GHz, 5GHz, and 5GHz-2 bands. 2.4GHz security settings 5GHz security settings
213. On the Wireless name (SSID) field, key in a unique name for your wireless network.4. From the Authentication Method dropdown list, select the authentication method for your wireless network. If you select WPA-Personal or WPA-2 Personal as the authenticationmethod,keyintheWPA-PSKkeyorsecuritypasskey.IMPORTANT! The IEEE 802.11n/ac standard prohibits using High Throughput with WEP or WPA-TKIP as the unicast cipher. If you use these encryption methods, your data rate will drop to IEEE 802.11g 54Mbps connection.5 Click Apply when done.5GHz-2 security settings
223.1.2 Managing your network clientsTo manage your network clients:1. From the navigation panel, go to General > Network Map tab.2. On the Network Map screen, select the Clients icon to display your network client’s information.3. To block a client’s access to your network, select the client and click the open lock icon.
233.1.3 Monitoring your USB deviceThe ASUS wireless router provides two USB ports for connecting USB devices or USB printer to allow you to share files and printer with clients in your network.NOTES:• Tousethisfeature,youneedtoplugaUSBstoragedevice,suchasaUSB hard disk or USB flash drive, to the USB 3.0/2.0 ports on the rear panel of your wireless router. Ensure that the USB storage device is formatted and partitioned properly. Refer to the Plug-n-Share Disk Support List at http://event.asus.com/networks/disksupport• TheUSBportssupporttwoUSBdrivesoroneprinterandoneUSBdrive at the same time.
24IMPORTANT! You first need to create a share account and its permission /access rights to allow other network clients to access the USB device via an FTP site/third-party FTP client utility, Servers Center, Samba, or AiCloud. For more details, refer to the section 3.5 Using the USB Application and 3.6 Using AiCloud in this user manual.To monitor your USB device:1. From the navigation panel, go to General > Network Map.2. OntheNetworkMapscreen,selecttheUSB Disk Status icon to display your USB device’s information.3. On the AiDisk Wizard field, click GO to set up an FTP server for Internet file sharing.NOTES:• Formoredetails,refertothesection3.5.2 Using Servers Center in this user manual.• ThewirelessrouterworkswithmostUSBHDDs/Flashdisks(upto4TB size) and supports read-write access for FAT16, FAT32, NTFS, and HFS+.
25Safely removing the USB diskIMPORTANT: Incorrect removal of the USB disk may cause data corruption.To safely remove the USB disk:1. From the navigation panel, go to General > Network Map.2. In the upper right corner, click > Eject USB disk. When the USB disk is ejected successfully, the USB status shows Unmounted.
263.2 Creating a Guest NetworkThe Guest Network provides temporary visitors with Internet connectivity via access to separate SSIDs or networks without providing access to your private network.NOTE: RT-AC5300 supports up to nine SSIDs (three 2.4GHz, three 5GHz-1 and three 5GHz-2 SSIDs).To create a guest network:1. From the navigation panel, go to General > Guest Network.2. On the Guest Network screen, select 2.4Ghz, 5Ghz-1, or 5Ghz-2 frequency band for the guest network that you want to create. 3. Click Enable.
274. To change a guest’s settings, click the guest settings you want to modify. Click Remove to delete the guest’s settings.5. Assign a wireless name for your temporary network on the Network Name (SSID) field.6. Select an Authentication Method.7. If you select a WPA authentication method, select a WPA Encryption.8. Specify the Access time or choose Limitless.9. Select Disable or Enable on the Access Intranet item.10. When done, click Apply.
283.3 AiProtectionAiProtection provides real-time monitoring that detects malware, spyware, and unwanted access. It also filters unwanted websites and apps and allows you to schedule a time that a connected device is able to access the Internet.
293.3.1 Network ProtectionNetwork Protection prevents network exploits and secures your network from unwanted access.Configuring Network ProtectionTo configure Network Protection:1. From the navigation panel, go to General > AiProtection. 2. From the AiProtection main page, click on Network Protection.3. From the Network Protection tab, click Scan. When done scanning, the utility displays the results on the Router Security Assessment page.
30IMPORTANT! Items marked as Ye s on the Router Security Assessment page is considered to be at a safe status. Items marked as No, Weak, or Very Weak is highly recommended to be configured accordingly. 4. (Optional) From the Router Security Assessment page, manually configure the items marked as No, Weak, or Very Weak. To do this: a. Click an item. NOTE: When you click an item, the utility forwards you to the item’s setting page. b. From the item’s security settings page, configure and make the necessary changes and click Apply when done. c. Go back to the Router Security Assessment page and click Close to exit the page.5. To automatically configure the security settings, click Secure Your Router.6. When a message prompt appears, click OK.
31Malicious Sites BlockingThis feature restricts access to known malicious websites in the cloud database for an always-up-to-date protection.NOTE: This function is automatically enabled if you run the Router Weakness Scan. To enable Malicious Sites Blocking:1. From the navigation panel, go to General > AiProtection. 2. From the AiProtection main page, click on Network Protection.3. From the Malicious Sites Blocking pane, click ON.Vulnerability protectionThis feature resolves common exploits within the router configuration.NOTE: This function is automatically enabled if you run the Router Weakness Scan. To enable Vulnerability protection:1. From the navigation panel, go to General > AiProtection. 2. From the AiProtection main page, click on Network Protection.3. From the Vulnerability protection pane, click ON.
32Infected Device Prevention and BlockingThis feature prevents infected devices from communicating personal information or infected status to external parties.NOTE: This function is automatically enabled if you run the Router Weakness Scan. To enable Vulnerability protection:1. From the navigation panel, go to General > AiProtection. 2. From the AiProtection main page, click on Network Protection.3. From the Infected Device Prevention and Blocking pane, click ON.To configure Alert Preference:1. From the Infected Device Prevention and Blocking pane, click Alert Preference.2. Select or key in the e-mail provider, e-mail account, and password then click Apply.
333.3.2 Setting up Parental ControlsParental Control allows you to control the Internet access time or set the time limit for a client’s network usage.To go to the Parental Controls main page:1. From the navigation panel, go to General > AiProtection.2. From the AiProtection main page, click on the Parental Controls tab.
34Web & Apps FiltersWeb & Apps Filters is a feature of Parental Controls that allows you to block access to unwanted web sites or applications.To configure Web & Apps Filters:1. From the navigation panel, go to General > AiProtection.2. From the AiProtection main page, click on the Parental Controls icon to go to the Parental Controls tab.3. From the Enable Web & Apps Filters pane, click ON. 4. When the End Users License Agreement (EULA) message prompt appears, click I agree to continue.5. From the Client List column, select or key in the client’s name from the drop down list box. 6. From the Content Category column, select the filters from the four main categories: Adult, Instant Message and Communication, P2P and File Transfer, and Streaming and Entertainment.7. Click to add the client’s profile.8. Click Apply to save the settings.
35Time SchedulingTime Scheduling allows you to set the time limit for a client’s network usage.NOTE: Ensure that your system time is synchronized with the NTP server.To configure Time Scheduling:1. From the navigation panel, go to General >AiProtection > Parental Controls > Time Scheduling.2. From the Enable Time Scheduling pane, click ON.
363. From the Clients Name column, select or key in the client’s name from the drop down list box. NOTE: You may also key in the client’s MAC address in the Client MAC Address column. Ensure that the client name does not contain special characters or spaces as these may cause the router to function abnormally.4. Click to add the client’s profile.5. Click Apply to save the settings.
373.4 Adaptive QoS3.4.1 Bandwidth MonitorThis feature allows you to monitor the bandwidth of WAN/LAN and displays the upload and download speed of your connection.Apps analysisTo enable Apps analysis:From the Bandwidth Monitor tab, go to the Apps Analysis pane, click ON.
383.4.2 QoSThis feature ensures bandwidth for prioritized tasks and applications. To enable the QoS function:1. From the navigation panel, go to General > Adaptive QoS> QoS tab.2. From the Enable Smart QoS pane, click ON. 3. Fill in the upload and download bandwidth fields.NOTE: Get the bandwidth information from your ISP. You can also go to http://speedtest.net to check and get your bandwidth.4. Select the QoS Type (Adaptive or Traditional) for your configuration. NOTE: The definition of the QoS Type is displayed on the QoS tab for your reference. 5. Click Apply.
393.4.3 Web HistoryThis feature displays the history and details of the sites or URLs that the client visited.To view the Web History:1. From the navigation panel, go to General > Adaptive QoS> Web History tab.2. (Optional) Click Refresh to clear the list.
403.4.4 Traffic MonitorThe traffic monitor feature allows you to access the bandwidth usage and speed of your Internet, wired, or wireless networks. It allows you to monitor network traffic in real-time or on a daily basis. It also offers an option to display the network traffic within the last 24 hours.To configure Traffic Monitor:1. From the navigation panel, go to General > Adaptive QoS> Traffic Monitor tab.2. (Optional) From the Traffic Manager - Traffic Monitor pane, select an option (Real-Time, Last 24 Hours, or Daily) from the drop down list box.
413.5 Using the USB ApplicationThe USB Applications function provides AiDisk, Servers Center, Network Printer Server and Download Master submenus.IMPORTANT! To use the server functions, you need to insert a USB storage device, such as a USB hard disk or USB flash drive, in the USB 2.0 port on the rear panel of your wireless router. Ensure that the USB storage device is formatted and partitioned properly. Refer to the ASUS website at http://event.asus.com/2009/networks/disksupport/ for the file system support table.3.5.1 Using AiDiskAiDisk allows you to share files stored on a connected USB device through the Internet. AiDisk also assists you with setting up ASUS DDNS and an FTP server. To use AiDisk:1. From the navigation panel, go to General > USB application, then click the AiDisk icon.2. From the Welcome to AiDisk wizard screen, click Go.
424. Create your domain name via the ASUS DDNS services, read the Terms of Service and then select I will use the service and accept the Terms of service and key in your domain name. When done, click Next. You can also select Skip ASUS DDNS settings then click Next to skip the DDNS setting.5. Click Finish to complete the setting.6. To access the FTP site that you created, launch a web browser or a third-party FTP client utility and key in the ftp link (ftp://<domain name>.asuscomm.com) you have previously created.3. Select the access rights that you want to assign to the clients accessing your shared data.
433.5.2 Using Servers CenterServers Center allows you to share the media files from the USB disk via a Media Server directory, Samba share service, or FTP share service. You can also configure other settings for the USB disk in the Servers Center.Using Media ServerYour wireless router allows DLNA-supported devices to access multimedia files from the USB disk connected to your wireless router.NOTE: Before using the DLNA Media Server function, connect your device to the RT-AC5300’s network.
44To launch the Media Server setting page, go to General > USB application > Media Services and Servers > Media Servers tab. Refer to the following for the descriptions of the fields:• Enable iTunes Server?: Select ON/OFF to enable/disable the iTunes Server.• Enable DLNA Media Server: Select ON/OFF to enable/ disable the DLNA Media Server.• Media Server Status: Displays the status of the media server. • Media Server Path Setting: Select All Disks Shared or Manual Media Server Path.Using Network Place (Samba) Share serviceNetwork Place (Samba) Share allows you to set up the accounts and permissions for the Samba service.To use Samba share:1. From the navigation panel, go to General > USB application > Media Services and Servers > Network Place (Samba) Share / Cloud Disk tab. NOTE: Network Place (Samba) Share is enabled by default.
45 To delete an existing account:a) Select the account that you want to delete.b) Click .c) When prompted, click Delete to confirm the account deletion. To add a folder:a) Click .b) Enter the folder name, and click Add. The folder that you created will be added to the folder list.2. Follow the steps below to add, delete, or modify an account. To create a new account:a) Click to add new account.b) In the Account and Password fields, key in the name and password of your network client. Retype the password to confirm. Click Add to add the account to the list.
463. From the list of folders, select the type of access permission that you want to assign for specific folders:• R/W: Select this option to assign read/write access.• R: Select this option to assign read-only access.• No: Select this option if you do not want to share a specific file folder.4. Click Apply to apply the changes.Using the FTP Share serviceFTP share enables an FTP server to share files from USB disk to other devices via your local area network or via the Internet.IMPORTANT: • EnsurethatyousafelyremovetheUSBdisk.IncorrectremovaloftheUSB disk may cause data corruption.• TosafelyremovetheUSBdisk,refertothesectionSafely removing the USB disk under 3.1.3 Monitoring your USB device.
47To use FTP Share service:NOTE: Ensure that you have set up your FTP server through AiDisk. For more details, refer to the section 3.5.1 Using AiDisk.1. From the navigation panel, click General > USB application > Media Services and Servers > FTP Share tab. 2. From the list of folders, select the type of access rights that you want to assign for specific folders:• R/W: Select to assign read/write access for a specific folder.• W: Select to assign write only access for a specific folder.• R: Select to assign read only access for a specific folder.• No: Select this option if you do not want to share a specific folder.3. If you prefer, you can set the Allow anonymous login field to ON.4. In the Maximum number of concurrent connections field, key in the number of devices that can simultaneously connect to the FTP share server.5. Click Apply to confirm the changes.6. To access the FTP server, key in the ftp link ftp://<hostname>.asuscomm.com and your user name and password on a web browser or a third-party FTP utility.
483.5.3 3G/4G3G/4G USB modems can be connected to RT-AC5300 to allow Internet access.NOTE: For a list of verified USB modems, please visit: http://event.asus.com/2009/networks/3gsupport/To set up 3G/4G internet access:1. From the navigation panel, click General > USB application > 3G/4G.2. In the Enable USB Modem field, select Yes. 3. Set up the following:• Location: Select your 3G/4G service provider’s location from the dropdown list.• ISP: Select your Internet Service Provider (ISP) from the dropdown list.• APN (Access Point Name) service (optional): Contact your 3G/4G service provider for detailed information.• Dial Number and PIN code: The 3G/4G provider’s access number and PIN code for connection.NOTE: PIN code may vary from dierent providers.• Username / Password: The username and password will be provided by the 3G/4G network carrier.• USB Adapter: Choose your USB 3G / 4G adapter from the dropdown list. If you are not sure of your USB adapter’s model or the model is not listed in the options, select Auto.4. Click Apply.NOTE: The router will reboot for the settings to take eect.
493.6 Using AiCloud 2.0AiCloud 2.0 is a cloud service application that allows you to save, sync, share, and access your files.To use AiCloud:1. From Google Play Store or Apple Store, download and install the ASUS AiCloud app to your smart device. 2. Connect your smart device to your network. Follow the instructions to complete the AiCloud setup process.
503.6.1 Cloud DiskTo create a cloud disk:1. Insert a USB storage device into the wireless router.2. Turn on Cloud Disk.3. Go to https://router.asus.com and enter the router login account and password. For better user experience, we recommend that you use Google Chrome or Firefox.
514. You can now start accessing Cloud Disk files on devices connected to the network.NOTE: When accessing the devices that are connected to the network, you need to enter the device’s user name and password manually, which will not be saved by AiCloud for security reason.
523.6.2 Smart AccessThe Smart Access function allows you to easily access your home network via your router’s domain name.NOTES: • YoucancreateadomainnameforyourrouterwithASUSDDNS.Formore details, refer to section 4.3.5 DDNS.• Bydefault,AiCloudprovidesasecureHTTPSconnection.Keyinhttps://[yourASUSDDNSname].asuscomm.com for a very secure Cloud Disk and Smart Access usage.
533.6.3 Smart SyncTo use Smart Sync:1. Launch AiCloud, click Smart Sync > Go.2. Select ON to enable Smart Sync.3. Click Add new account. 4. Enter your ASUS WebStorage account password and select the directory that you want to sync with WebStorage.5. Click Apply.
544 Configuring the Advanced Settings4.1 Wireless4.1.1 GeneralThe General tab allows you to configure the basic wireless settings. To configure the basic wireless settings:1. From the navigation panel, go to Advanced Settings > Wireless > General tab.2. Select 2.4GHz, 5GHz-1, or 5GHz-2 as the frequency band for your wireless network.3. If you want to use the Smart Connect function, move the slider to ON in the Enable Smart Connect field. This function automatically connect the clients in your network to the appropriate band 2.4GHz, 5GHz-1, or 5GHz-2 for optimal speed.
554. Assign a unique name containing up to 32 characters for your SSID (Service Set Identifier) or network name to identify your wireless network. Wi-Fi devices can identify and connect to the wireless network via your assigned SSID. The SSIDs on the information banner are updated once new SSIDs are saved to the settings.NOTE: You can assign unique SSIDs for the 2.4 GHz, 5GHz-1, and 5GHz-2 frequency bands. 5. In the Hide SSID field, select Ye s to prevent wireless devices from detecting your SSID. When this function is enabled, you would need to enter the SSID manually on the wireless device to access the wireless network.6. Select any of these wireless mode options to determine the types of wireless devices that can connect to your wireless router:• Auto: Select Auto to allow 802.11AC, 802.11n, 802.11g, and 802.11b devices to connect to the wireless router.• N only: Select N only to maximize wireless N performance. This setting prevents 802.11g and 802.11b devices from connecting to the wireless router.• Legacy: Select Legacy to allow 802.11b/g/n devices to connect to the wireless router. Hardware that supports 802.11n natively, however, will only run at a maximum speed of 54Mbps. 7. Select the operating/control channel for your wireless router. Select Auto to allow the wireless router to automatically select the channel that has the least amount of interference.8. Select the channel bandwidth to accommodate higher transmission speeds.9. Select the authentication method.NOTE: Your wireless router supports the maximum transmission rate of 54Mbps when the Wireless Mode is set to Auto.10. When done, click Apply.
564.1.2 WPSWPS (Wi-Fi Protected Setup) is a wireless security standard that allows you to easily connect devices to a wireless network. You can configure the WPS function via the PIN code or WPS button. NOTE: Ensure that the devices support WPS.To enable WPS on your wireless network:1. From the navigation panel, go to Advanced Settings > Wireless > WPS tab. 2. In the Enable WPS field, move the slider to ON.3. WPS uses 2.4GHz by default. If you want to change the frequency to 5GHz-1 or 5GHz-2, turn OFF the WPS function, click Switch Frequency in the Current Frequency field, and turn WPS ON again.
57NOTE: WPS supports authentication using Open System, WPA-Personal, and WPA2-Personal. WPS does not support a wireless network that uses a Shared Key, WPA-Enterprise, WPA2-Enterprise, and RADIUS encryption method.3. In the WPS Method field, select Push Button or Client PIN code. If you select Push Button, go to step 4. If you select Client PIN code, go to step 5.4. To set up WPS using the router’s WPS button, follow these steps:a. Click Start or press the WPS button found at the rear of the wireless router. b. Press the WPS button on your wireless device. This is normally identified by the WPS logo.NOTE: Check your wireless device or its user manual for the location of the WPS button.c. The wireless router will scan for any available WPS devices. If the wireless router does not find any WPS devices, it will switch to standby mode.5. To set up WPS using the Client’s PIN code, follow these steps:a. Locate the WPS PIN code on your wireless device’s user manual or on the device itself. b. Key in the Client PIN code on the text box.c. Click Start to put your wireless router into WPS survey mode. The router’s LED indicators quickly flash three times until the WPS setup is completed.
584.1.3 Wireless MAC FilterWireless MAC filter provides control over packets transmitted to a specified MAC (Media Access Control) address on your wireless network.To set up the Wireless MAC filter:1. From the navigation panel, go to Advanced Settings > Wireless > Wireless MAC Filter tab.2. Tick Yes in the Enable Mac Filter field.3. In the MAC Filter Mode dropdown list, select either Accept or Reject.• SelectAccept to allow devices in the MAC filter list to access to the wireless network.• SelectReject to prevent devices in the MAC filter list to access to the wireless network.4. On the MAC filter list, click the Add button and key in the MAC address of the wireless device.5. Click Apply.
594.1.4 RADIUS SettingRADIUS (Remote Authentication Dial In User Service) Setting provides an extra layer of security when you choose WPA-Enterprise, WPA2-Enterprise, or Radius with 802.1x as your Authentication Mode.To set up wireless RADIUS settings:1. Ensure that the wireless router’s authentication mode is set to WPA-Enterprise or WPA2-Enterprise.NOTE: Please refer to section 4.1.1 General section for configuring your wireless router’s Authentication Mode.2. From the navigation panel, go to Advanced Settings > Wireless > RADIUS Setting.3. Select the frequency band.4. In the Server IP Address field, key in your RADIUS server’s IP Address.5. In the Server Port field, key in the server port.6. In the Connection Secret field, assign the password to access your RADIUS server.7. Click Apply.
60In the Professional Settings screen, you can configure the following:• Frequency: Select the frequency band that the professional settings will be applied to.• Enable Radio: Select Yes to enable wireless networking. Select No to disable wireless networking.• Date to Enable Radio (weekdays): You can specify which days of the week wireless networking is enabled.• Time of Day to Enable Radio: You can specify a time range when wireless networking is enabled during the week.4.1.5 ProfessionalThe Professional screen provides advanced configuration options. NOTE: We recommend that you use the default values on this page.
61• Date to Enable Radio (weekend): You can specify which days of the weekend wireless networking is enabled.• Time of Day to Enable Radio: You can specify a time range when wireless networking is enabled during the weekend.• Set AP isolated: The Set AP isolated item prevents wireless devices on your network from communicating with each other. This feature is useful if many guests frequently join or leave your network. Select Ye s to enable this feature or select No to disable.• Multicast rate (Mbps): Select the multicast transmission rate or click Disable to switch off simultaneous single transmission.• Preamble Type: Preamble Type defines the length of time that the router spent for CRC (Cyclic Redundancy Check). CRC is a method of detecting errors during data transmission. Select Short for a busy wireless network with high network traffic. Select Long if your wireless network is composed of older or legacy wireless devices.• AMPDU RTS:• RTS Threshold: Select a lower value for RTS (Request to Send) Threshold to improve wireless communication in a busy or noisy wireless network with high network traffic and numerous wireless devices.• DTIM Interval: DTIM (Delivery Traffic Indication Message) Interval or Data Beacon Rate is the time interval before a signal is sent to a wireless device in sleep mode indicating that a data packet is awaiting delivery. The default value is three milliseconds. • Beacon Interval: Beacon Interval is the time between one DTIM and the next. The default value is 100 milliseconds. Lower the Beacon Interval value for an unstable wireless connection or for roaming devices. • Enable TX Bursting: Enable TX Bursting improves transmission speed between the wireless router and 802.11g devices.
62• Enable WMM APSD: Enable WMM APSD (Wi-Fi Multimedia Automatic Power Save Delivery) to improve power management between wireless devices. Select Disable to switch off WMM APSD.• TX Power adjustment: TX Power adjustment refers to the milliWatts (mW) needed to power the radio signal output of the wireless router. Enter a value between 0 to 100. NOTE: Increasing the TX Power adjustment values may affect the stability of the wireless network.4.2 LAN4.2.1 LAN IPThe LAN IP screen allows you to modify the LAN IP settings of your wireless router.NOTE: Any changes to the LAN IP address will be reflected on your DHCP settings.To modify the LAN IP settings:1. From the navigation panel, go to Advanced Settings > LAN > LAN IP tab.2. Modify the IP address and Subnet Mask.3. When done, click Apply.
634.2.2 DHCP ServerYour wireless router uses DHCP to assign IP addresses automatically on your network. You can specify the IP address range and lease time for the clients on your network.To configure the DHCP server:1. From the navigation panel, go to Advanced Settings > LAN > DHCP Server tab.2. In the Enable the DHCP Server field, tick Yes .3. In the Domain Name text box, enter a domain name for the wireless router.4. In the IP Pool Starting Address field, key in the starting IP address.
645. In the IP Pool Ending Address field, key in the ending IP address.6. In the Lease Time field, specify in seconds when an assigned IP address will expire. Once it reaches this time limit, the DHCP server will then assign a new IP address.NOTES:• We recommend that you use an IP address format of 192.168.1.xxx (where xxx can be any number between 2 and 254) when specifying an IP address range.• AnIPPoolStartingAddressshouldnotbegreaterthantheIPPoolEnding Address.7. In the DNS and Server Settings section, key in your DNS Server and WINS Server IP address if needed.8. Your wireless router can also manually assign IP addresses to devices on the network. On the Enable Manual Assignment field, choose Yes to assign an IP address to specific MAC addresses on the network. Up to 32 MAC Addresses can be added to the DHCP list for manual assignment.
654.2.3 RouteIf your network makes use of more than one wireless router, you can configure a routing table to share the same Internet service.NOTE: We recommend that you do not change the default route settings unless you have advanced knowledge of routing tables. To configure the LAN Routing table:1. From the navigation panel, go to Advanced Settings > LAN > Route tab. 2. On the Enable static routes field, choose Ye s.3. On the Static Route List, enter the network information of other access points or nodes. Click the Add or Delete button to add or remove a device on the list.4. Click Apply.
664.2.4 IPTVThe wireless router supports connection to IPTV services through an ISP or a LAN. The IPTV tab provides the configuration settings needed to set up IPTV, VoIP, multicasting, and UDP for your service. Contact your ISP for specific information regarding your service.
674.3 WAN4.3.1 Internet ConnectionThe Internet Connection screen allows you to configure the settings of various WAN connection types. To configure the WAN connection settings:1. From the navigation panel, go to Advanced Settings > WAN > Internet Connection tab.2. Configure the following settings below. When done, click Apply.• WAN Connection Type: Choose your Internet Service Provider type. The choices are Automatic IP, PPPoE, PPTP, L2TP or static IP. Consult your ISP if the router is unable to obtain a valid IP address or if you are unsure the WAN connection type.• Enable WAN: Select Ye s to allow the router Internet access. Select No to disable Internet access.
68• Enable NAT: NAT (Network Address Translation) is a system where one public IP (WAN IP) is used to provide Internet access to network clients with a private IP address in a LAN. The private IP address of each network client is saved in a NAT table and is used to route incoming data packets.• Enable UPnP: UPnP (Universal Plug and Play) allows several devices (such as routers, televisions, stereo systems, game consoles, and cellular phone), to be controlled via an IP-based network with or without a central control through a gateway. UPnP connects PCs of all form factors, providing a seamless network for remote configuration and data transfer. Using UPnP, a new network device is discovered automatically. Once connected to the network, devices can be remotely configured to support P2P applications, interactive gaming, video conferencing, and web or proxy servers. Unlike Port forwarding, which involves manually configuring port settings, UPnP automatically configures the router to accept incoming connections and direct requests to a specific PC on the local network. • Connect to DNS Server automatically: Allows this router to get the DNS IP address from the ISP automatically. A DNS is a host on the Internet that translates Internet names to numeric IP addresses. • Authentication: This item may be specified by some ISPs. Check with your ISP and fill them in if required.• Host Name: This field allows you to provide a host name for your router. It is usually a special requirement from your ISP. If your ISP assigned a host name to your computer, enter the host name here.
69• MAC Address: MAC (Media Access Control) address is a unique identifier for your networking device. Some ISPs monitor the MAC address of networking devices that connect to their service and reject any unrecognized device that attempt to connect. To avoid connection issues due to an unregistered MAC address, you can:• ContactyourISPandupdatetheMACaddressassociatedwith your ISP service.• CloneorchangetheMACaddressoftheASUSwirelessrouterto match the MAC address of the previous networking device recognized by the ISP. • DHCP query frequency: Changes the DHCP Discovery interval settings to avoid overloading the DHCP server.
704.3.2 Dual WANYour ASUS wireless router provides dual WAN support. You can set the dual WAN feature to any of these two modes:• Failover Mode: Select this mode to use the secondary WAN as the backup network access.• Load Balance Mode: Select this mode to optimize bandwidth, minimize response time and prevent data overload for both primary and secondary WAN connections.
714.3.3 Port TriggerPort range triggering opens a predetermined incoming port for a limited period of time whenever a client on the local area network makes an outgoing connection to a specified port. Port triggering is used in the following scenarios:• More than one local client needs port forwarding for the same application at a different time.• An application requires specific incoming ports that are different from the outgoing ports.To set up Port Trigger:1. From the navigation panel, go to Advanced Settings > WAN > Port Trigger tab.2. On the Enable Port Trigger field, tick Yes.3. On the Well-Known Applications field, select the popular games and web services to add to the Port Trigger List.
724. On the Trigger Port List table, key in the following information:• Description: Enter a short name or description for the service.• Trigger Port: Specify a trigger port to open the incoming port.• Protocol: Select the protocol, TCP, or UDP.• Incoming Port: Specify an incoming port to receive inbound data from the Internet.• Protocol: Select the protocol, TCP, or UDP.5. Click the Add to enter the port trigger information to the list. Click the Delete button to remove a port trigger entry from the list.6. When done, click Apply.NOTES:• WhenconnectingtoanIRCserver,aclientPCmakesanoutgoingconnection using the trigger port range 66660-7000. The IRC server responds by verifying the username and creating a new connection to the client PC using an incoming port.• IfPortTriggerisdisabled,therouterdropstheconnectionbecauseit is unable to determine which PC is requesting for IRC access. When Port Trigger is enabled, the router assigns an incoming port to receive the inbound data. This incoming port closes once a specific time period has elapsed because the router is unsure when the application has been terminated.• Porttriggeringonlyallowsoneclientinthenetworktouseaparticular service and a specific incoming port at the same time.• Youcannotusethesameapplicationtotriggeraportinmorethanone PC at the same time. The router will only forward the port back to the last computer to send the router a request/trigger.
734.3.4 Virtual Server/Port ForwardingPort forwarding is a method to direct network traffic from the Internet to a specific port or a specific range of ports to a device or number of devices on your local network. Setting up Port Forwarding on your router allows PCs outside the network to access specific services provided by a PC in your network.NOTE: When port forwarding is enabled, the ASUS router blocks unsolicited inbound traffic from the Internet and only allows replies from outbound requests from the LAN. The network client does not have access to the Internet directly, and vice versa.To set up Port Forwarding:1. From the navigation panel, go to Advanced Settings > WAN > Virtual Server / Port Forwarding tab.2. On the Enable Port Forwarding field, tick Yes.
743. On the Famous Server List field, select the type of service you want to access.4. On the Famous Game List field, select the popular game that you want to access. This item lists the port required for your selected popular online game to work properly.5. On the Port Forwarding List table, key in the following information:• Service Name: Enter a service name.• Port Range: If you want to specify a Port Range for clients on the same network, enter the Service Name, the Port Range (e.g. 10200:10300), the LAN IP address, and leave the Local Port empty. Port range accepts various formats such as Port Range (300:350), individual ports (566,789) or Mix (1015:1024,3021). NOTES:• Whenyournetwork’sfirewallisdisabledandyouset80astheHTTPserver’s port range for your WAN setup, then your http server/web server would be in conflict with the router’s web user interface.• Anetworkmakesuseofportsinordertoexchangedata,witheachport assigned a port number and a specific task. For example, port 80 is used for HTTP. A specific port can only be used by one application or service at a time. Hence, two PCs attempting to access data through the same port at the same time would fail. For example, you cannot set up Port Forwarding for port 100 for two PCs at the same time.• Local IP: Key in the client’s LAN IP address. NOTE: Use a static IP address for the local client to make port forwarding work properly. Refer to section 4.2 LAN for information.
75• Local Port: Enter a specific port to receive forwarded packets. Leave this field blank if you want the incoming packets to be redirected to the specified port range.• Protocol: Select the protocol. If you are unsure, select BOTH.5. Click the Add to enter the port trigger information to the list. Click the Delete button to remove a port trigger entry from the list.6. When done, click Apply.To check if Port Forwarding has been configured successfully:• Ensure that your server or application is set up and running.• You will need a client outside your LAN but has Internet access (referred to as “Internet client”). This client should not be connected to the ASUS router.• On the Internet client, use the router’s WAN IP to access the server. If port forwarding has been successful, you should be able to access the files or applications.Differences between port trigger and port forwarding: • Port triggering will work even without setting up a specific LAN IP address. Unlike port forwarding, which requires a static LAN IP address, port triggering allows dynamic port forwarding using the router. Predetermined port ranges are configured to accept incoming connections for a limited period of time. Port triggering allows multiple computers to run applications that would normally require manually forwarding the same ports to each PC on the network.• Port triggering is more secure than port forwarding since the incoming ports are not open all the time. They are opened only when an application is making an outgoing connection through the trigger port.
764.3.4 DMZVirtual DMZ exposes one client to the Internet, allowing this client to receive all inbound packets directed to your Local Area Network. Inbound traffic from the Internet is usually discarded and routed to a specific client only if port forwarding or a port trigger has been configured on the network. In a DMZ configuration, one network client receives all inbound packets. Setting up DMZ on a network is useful when you need incoming ports open or you want to host a domain, web, or e-mail server.CAUTION: Opening all the ports on a client to the Internet makes the network vulnerable to outside attacks. Please be aware of the security risks involved in using DMZ.To set up DMZ:1. From the navigation panel, go to Advanced Settings > WAN > DMZ tab.2. Configure the setting below. When done, click Apply.• IP address of Exposed Station: Key in the client’s LAN IP address that will provide the DMZ service and be exposed on the Internet. Ensure that the server client has a static IP address.To remove DMZ:1. Delete the client’s LAN IP address from the IP Address of Exposed Station text box.2. When done, click Apply.
774.3.5 DDNSSetting up DDNS (Dynamic DNS) allows you to access the router from outside your network through the provided ASUS DDNS Service or another DDNS service.To set up DDNS:1. From the navigation panel, go to Advanced Settings > WAN > DDNS tab.2. Configure the following settings below. When done, click Apply.• Enable the DDNS Client: Enable DDNS to access the ASUS router via the DNS name rather than WAN IP address.• Server and Host Name: Choose ASUS DDNS or other DDNS. If you want to use ASUS DDNS, fill in the Host Name in the format of xxx.asuscomm.com (xxx is your host name). • If you want to use a different DDNS service, click FREE TRIAL and register online first. Fill in the User Name or E-mail Address and Password or DDNS Key fields.
78• Enable wildcard: Enable wildcard if your DDNS service requires one.NOTES: DDNS service will not work under these conditions:• WhenthewirelessrouterisusingaprivateWANIPaddress(192.168.x.x, 10.x.x.x, or 172.16.x.x), as indicated by a yellow text.• TheroutermaybeonanetworkthatusesmultipleNATtables.4.3.6 NAT PassthroughNAT Passthrough allows a Virtual Private Network (VPN) connection to pass through the router to the network clients. PPTP Passthrough, L2TP Passthrough, IPsec Passthrough and RTSP Passthrough are enabled by default.To enable / disable the NAT Passthrough settings, go to the Advanced Settings > WAN > NAT Passthrough tab. When done, click Apply.
794.4 IPv6This wireless router supports IPv6 addressing, a system that supports more IP addresses. This standard is not yet widely available. Contact your ISP if your Internet service supports IPv6. To set up IPv6:1. From the navigation panel, go to Advanced Settings > IPv6.2. Select your Connection Type. The configuration options vary depending on your selected connection type.3. Enter your IPv6 LAN and DNS settings.4. Click Apply.NOTE: Please refer to your ISP regarding specific IPv6 information for your Internet service.
804.5 VPN ServerVPN (Virtual Private Network) provides a secure communication to a remote computer or remote network using a public network such as the Internet.NOTE: Before setting up a VPN connection, you would need the IP address or domain name of the VPN server you are trying to access.To set up access to a VPN server:1. From the navigation panel, go to Advanced Settings > VPN Server.2. On the Enable VPN Server field, select Yes .3. On the VPN Details dropdown list, select Advanced Settings if want to configure advanced VPN settings such as broadcast support, authentication, MPPE Encryption, and Client IP address range.4. On the Network Place (Samba) Support field, select Ye s .5. Enter the user name and password for accessing the VPN server. Click the button.6. Click Apply.
814.6 FirewallThe wireless router can serve as a hardware firewall for your network. NOTE: The Firewall feature is enabled by default.4.6.1 GeneralTo set up basic Firewall settings:1. From the navigation panel, go to Advanced Settings > Firewall > General tab.2. On the Enable Firewall field, select Ye s.3. On the Enable DoS protection, select Ye s to protect your network from DoS (Denial of Service) attacks though this may affect your router’s performance. 4. You can also monitor packets exchanged between the LAN and WAN connection. On the Logged packets type, select Dropped, Accepted, or Both.5. Click Apply.4.6.2 URL FilterYou can specify keywords or web addresses to prevent access to specific URLs.NOTE: The URL Filter is based on a DNS query. If a network client has already accessed a website such as http://www.abcxxx.com, then the website will not be blocked (a DNS cache in the system stores previously visited websites). To resolve this issue, clear the DNS cache before setting up the URL Filter.
82To set up a URL filter:1. From the navigation panel, go to Advanced Settings > Firewall > URL Filter tab.2. On the Enable URL Filter field, select Enabled.3. Enter a URL and click the button.4. Click Apply.4.6.3 Keyword filterKeyword filter blocks access to webpages containing specified keywords.To set up a keyword filter:1. From the navigation panel, go to Advanced Settings > Firewall > Keyword Filter tab.2. On the Enable Keyword Filter field, select Enabled.
833. Enter a word or phrase and click the Add button.4. Click Apply.NOTES:• The Keyword Filter is based on a DNS query. If a network client has already accessed a website such as http://www.abcxxx.com, then the website will not be blocked (a DNS cache in the system stores previously visited websites). To resolve this issue, clear the DNS cache before setting up the Keyword Filter.• Web pages compressed using HTTP compression cannot be filtered. HTTPS pages also cannot be blocked using a keyword filter.4.6.4 Network Services FilterThe Network Services Filter blocks LAN to WAN packet exchanges and restricts network clients from accessing specific web services such as Telnet or FTP.
84To set up a Network Service filter:1. From the navigation panel, go to Advanced Settings > Firewall > Network Service Filter tab.2. On the Enable Network Services Filter field, select Yes .3. Select the Filter table type. Black List blocks the specified network services. White List limits access to only the specified network services.4. Specify the day and time when the filters will be active. 5. To specify a Network Service to filter, enter the Source IP, Destination IP, Port Range, and Protocol. Click the button.6. Click Apply.4.6.5 IPv6 FirewallBy default, your ASUS wireless router blocks all unsolicited incoming traffic. The IPv6 Firewall function allows incoming traffic coming from specified services to go through your network.
854.7 Administration4.7.1 Operation ModeThe Operation Mode page allows you to select the appropriate mode for your network.To set up the operating mode:1. From the navigation panel, go to Advanced Settings > Administration > Operation Mode tab.2. Select any of these operation modes:• Wireless router mode (default): In wireless router mode, the wireless router connects to the Internet and provides Internet access to available devices on its own local network.• Repeater Mode: In Repeater mode, your wireless router wirelessly connects to an existing wireless network to extend the wireless coverage. In this mode, the firewall, IP sharing, and NAT functions are disabled.• Access Point mode: In this mode, the router creates a new wireless network on an exising network.
86• Media Bridge: This setup requires two wireless routers. The second router serves as a media bridge where multiple devices such as Smart TVs and gaming consoles can be connected via ethernet.3. Click Apply.NOTE: The router will reboot when you change the modes.4.7.2 SystemThe System page allows you to configure your wireless router settings.To set up the System settings:1. From the navigation panel, go to Advanced Settings > Administration > System tab.2. You can configure the following settings:• Change router login password: You can change the password and login name for the wireless router by entering a new name and password.• Time Zone: Select the time zone for your network.• NTP Server: The wireless router can access a NTP (Network time Protocol) server in order to synchronize the time.• Enable Telnet: Click Yes to enable Telnet services on the network. Click No to disable Telnet.• Authentication Method: You can select HTTP, HTTPS, or both protocols to secure router access.• Enable Web Access from WAN: Select Yes to allow devices outside the network to access the wireless router GUI settings. Select No to to prevent access.
87• Allow only specified IP address: Click Yes if you want to specify the IP addresses of devices that are allowed access to the wireless router GUI settings from WAN. • Client List: Enter the WAN IP addresses of networking devices allowed to access the wireless router settings. This list will be used if you clicked Yes in the Only allow specific IP item.3. Click Apply.4.7.3 Firmware UpgradeNOTE: Download the latest firmware from the ASUS website at http://www.asus.comTo upgrade the firmware:1. From the navigation panel, go to Advanced Settings > Administration > Firmware Upgrade tab.2. In the New Firmware File field, click Browse to locate the downloaded file.3. Click Upload. NOTES: • Whentheupgradeprocessiscomplete,waitforsometimeforthesystem to reboot. • Iftheupgradeprocessfails,thewirelessrouterautomaticallyentersrescue mode and the power LED indicator on the front panel starts flashing slowly. To recover or restore the system, refer to section 5.2 Firmware Restoration.
884.7.4 Restore/Save/Upload SettingTo restore/save/upload wireless router settings:1. From the navigation panel, go to Advanced Settings > Administration > Restore/Save/Upload Setting tab.2. Select the tasks that you want to do:• Torestoretothedefaultfactorysettings,clickRestore, and click OK in the confirmation message.• Tosavethecurrentsystemsettings,clickSave, navigate to the folder where you intend to save the file and click Save.• Torestorefromasavedsystemsettingsle,clickBrowse to locate your file, then click Upload.If issues occur, upload the latest firmware version and configure new settings. Do not restore the router to its default settings.
894.8 System LogSystem Log contains your recorded network activities.NOTE: System log resets when the router is rebooted or powered off.To view your system log:1. From the navigation panel, go to Advanced Settings > System Log.2. You can view your network activities in any of these tabs:• GeneralLog• DHCPLeases• WirelessLog• PortForwarding• RoutingTable
905 UtilitiesNOTES: • Download and install the wireless router's utilities from the ASUS website: Discovery v1.4.7.1 at http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Discovery.zip • Firmware • Device Restoration v1.9.0.4 at http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip • Windows Printer Utility v1.0.5.5 at http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Printer.zip• The utilities are not supported on MAC OS.5.1 Device DiscoveryDevice Discovery is an ASUS WLAN utility that detects an ASUS wireless router device, and allows you to configure the wireless networking settings.To launch the Device Discovery utility:• From your computer’s desktop, click Start > All Programs > ASUS Utility > RT-AC5300 Wireless Router > Device Discovery.NOTE: When you set the router to Access Point mode, you need to use Device Discovery to get the router’s IP address.
915.2 Firmware RestorationFirmware Restoration is used on an ASUS Wireless Router that failed during its firmware upgrading process. It uploads the firmware that you specify. The process takes about three to four minutes.IMPORTANT: Launch the rescue mode on the router before using the Firmware Restoration utility.NOTE: This feature is not supported on MAC OS.To launch the rescue mode and use the Firmware Restoration utility:1. Unplug the wireless router from the power source.2. Hold the Reset button at the rear panel and simultaneously replug the wireless router into the power source. Release the Reset button when the Power LED at the front panel flashes slowly, which indicates that the wireless router is in the rescue mode.
923. Set a static IP on your computer and use the following to set up your TCP/IP settings: IP address: 192.168.1.x Subnet mask: 255.255.255.04. From your computer’s desktop, click Start > All Programs > ASUS Utility RT-AC5300 Wireless Router > Firmware Restoration.5. Specify a firmware file, then click Upload.NOTE: This is not a firmware upgrade utility and cannot be used on a working ASUS Wireless Router. Normal firmware upgrades must be done through the web interface. Refer to Chapter 4: Configuring the Advanced Settings for more details.5.3 Setting up your printer server5.3.1 ASUS EZ Printer SharingASUS EZ Printing Sharing utility allows you to connect a USB printer to your wireless router’s USB port and set up the print server. This allows your network clients to print and scan files wirelessly.
93NOTE: The print server function is supported on Windows® XP, Windows® Vista, and Windows® 7.To set up the EZ Printer sharing mode:1. From the navigation panel, go to General > USB Application > Network Printer Server. 2. Click Download Now! to download the network printer utility.NOTE: Network printer utility is supported on Windows® XP, Windows® Vista, and Windows® 7 only. To install the utility on Mac OS, select Use LPR protocol for sharing printer.3. Unzip the downloaded file and click the Printer icon to run the network printer setup program.
944. Follow the onscreen instructions to set up your hardware, then click Next.5. Wait a few minutes for the initial setup to finish. Click Next.6. Click Finish to complete the installation.
958. After the printer’s driver installation is complete, network clients can now use the printer.7. Follow the Windows® OS instructions to install the printer driver.
965.3.2 Using LPR to Share PrinterYou can share your printer with computers running on Windows® and MAC operating system using LPR/LPD (Line Printer Remote/Line Printer Daemon).Sharing your LPR printerTo share your LPR printer:1. From the Windows® desktop, click Start > Devices and Printers > Add a printer to run the Add Printer Wizard.2. Select Add a local printer and then click Next.
973. Select Create a new port then set Type of Port to Standard TCP/IP Port. Click New Port.4. In the Hostname or IP address field, key in the IP address of the wireless router then click Next.
985. Select Custom then click Settings.6. Set Protocol to LPR. In the Queue Name field, key in LPRServer then click OK to continue.
997. Click Next to finish setting up the standard TCP/IP port.8. Install the printer driver from the vendor-model list. If your printer is not in the list, click Have Disk to manually install the printer drivers from a CD-ROM or file.
1009. Click Next to accept the default name for the printer.10. Click Finish to complete the installation.
101 5.4 Download MasterDownload Master is a utility that helps you download files even while your laptops or other devices are switched off.NOTE: You need a USB device connected to the wireless router to use Download Master.To use Download Master:1. Click General > USB application > Download Master to download and install the utility automatically. NOTE: If you have more than one USB drive, select the USB device you want to download the files to.2. After the download process is finished, click the Download Master icon to start using the utility.3. Click Add to add a download task.4. Select a download type such as BitTorrent, HTTP, or FTP. Provide a torrent file or a URL to begin downloading.NOTE: For details on Bit Torrent, refer to section 5.4.1 Configuring the Bit Torrent download settings.
1025. Use the navigation panel to configure the advanced settings.To configure BitTorrent download settings:1. From Download Master’s navigation panel, click Bit Torrent to launch the Bit Torrent Setting page.2. Select a specific port for your download task.3. To prevent network congestion, you can limit the maximum upload and download speeds under Speed Limits.4. You can limit the maximum number of allowed peers and enable or disable file encryption during downloads.5.4.1 Configuring Bit Torrent download settings
1035.4.2 NZB settingsYou can set up a USENET server to download NZB files. After entering USENET settings, Apply.
1046 TroubleshootingThis chapter provides solutions for issues you may encounter with your router. If you encounter problems that are not mentioned in this chapter, visit the ASUS support site at: http://support.asus.com/ for more product information and contact details of ASUS Technical Support.6.1 Basic TroubleshootingIf you are having problems with your router, try these basic steps in this section before looking for further solutions.Upgrade Firmware to the latest version.1. Launch the Web GUI. Go to Advanced Settings > Administration > Firmware Upgrade tab. Click Check to verify if the latest firmware is available. 2. If the latest firmware is available, visit the ASUS global website at http://www.asus.com/Networks/Wireless_Routers/RTAC87U/#download to download the latest firmware. 3. From the Firmware Upgrade page, click Browse to locate the firmware file. 4. Click Upload to upgrade the firmware.
105Restart your network in the following sequence:1. Turn off the modem.2. Unplug the modem.3. Turn off the router and computers.4. Plug in the modem.5. Turn on the modem and then wait for 2 minutes.6. Turn on the router and then wait for 2 minutes.7. Turn on computers.Check if your Ethernet cables are plugged properly.• WhentheEthernetcableconnectingtherouterwiththemodem is plugged in properly, the WAN LED will be on. • WhentheEthernetcableconnectingyourpowered-oncomputer with the router is plugged in properly, the corresponding LAN LED will be on. Check if the wireless setting on your computer matches that of your computer.• Whenyouconnectyourcomputertotherouterwirelessly,ensure that the SSID (wireless network name), encryption mehtod, and password are correct.Check if your network settings are correct. • EachclientonthenetworkshouldhaveavalidIPaddress.ASUS recommends that you use the wireless router’s DHCP server to assign IP addresses to computers on your network.
106• Somecablemodemserviceprovidersrequireyoutousethe MAC address of the computer initially registered on the account. You can view the MAC address in the web GUI, Network Map > Clients page, and hover the mouse pointer over your device in Client Status.
1076.2 Frequently Asked Questions (FAQs) I cannot access the router GUI using a web browser• Ifyourcomputeriswired,checktheEthernetcableconnection and LED status as described in the previous section.• Ensurethatyouareusingthecorrectlogininformation.Thedefault factory login name and password is “admin/admin”. Ensure that the Caps Lock key is disabled when you enter the login information.• Deletethecookiesandlesinyour web browser. For Internet Explorer 8, follow these steps: 1. Launch Internet Explorer 8, then click Tools > Internet Options. 2. In the General tab, under Browsing history, click Delete…, select Temporary Internet Files and Cookies then click Delete. NOTES: • Thecommandsfordeletingcookiesandfilesvarywithwebbrowsers.• Disableproxyserversettings,cancelthedial-upconnection,and set the TCP/IP settings to obtain IP addresses automatically. For more details, refer to Chapter 1 of this user manual.• EnsurethatyouuseCAT5eorCAT6ethernetcables.
108The client cannot establish a wireless connection with the router.NOTE: If you are having issues connecting to 5Ghz network, make sure that your wireless device supports 5Ghz or features dual band capabilities.• OutofRange: • Movetherouterclosertothewirelessclient. • Trytoadjustantennasoftheroutertothebestdirectionas described in section 1.4 Positioning your router. • DHCPserverhasbeendisabled: 1. Launch the web GUI. Go to General > Network Map> Clients and search for the device that you want to connect to the router. 2. If you cannot find the device in the Network Map, go to Advanced Settings > LAN > DHCP Server, Basic Config list, select Ye s on the Enable the DHCP Server.
109• SSIDhasbeenhidden.IfyourdevicecanndSSIDsfromotherrouters but cannot find your router’s SSID, go to Advanced Settings > Wireless > General, select No on Hide SSID, and select Auto on Control Channel. • IfyouareusingawirelessLANadapter,checkifthewirelesschannel in use conforms to the channels available in your country/area. If not, adjust the channel, channel bandwidth, and wireless mode.• Ifyoustillcannotconnecttotherouterwirelessly,youcanreset your router to factory default settings. In the router GUI,click Administration > Restore/Save/Upload Setting and click Restore.
110Internet is not accessible.• CheckifyourroutercanconnecttoyourISP’sWANIPaddress.To do this, launch the web GUI and go to General> Network Map, and check the Internet Status. • IfyourroutercannotconnecttoyourISP’sWANIPaddress,try restarting your network as described in the section Restart your network in following sequence under Basic Troubleshooting. • ThedevicehasbeenblockedviatheParentalControlfunction. Go to General > Parental Control and see if the device is in the list. If the device is listed under Client Name, remove the device using the Delete button or adjust the Time Management Settings.
111• IfthereisstillnoInternetaccess,trytorebootyourcomputerand verify the network’s IP address and gateway address. • CheckthestatusindicatorsontheADSLmodemandthewireless router. If the WAN LED on the wireless router is not ON, check if all cables are plugged properly.You forgot the SSID (network name) or network password• SetupanewSSIDandencryptionkeyviaawiredconnection(Ethernet cable). Launch the web GUI, go to Network Map, click the router icon, enter a new SSID and encryption key, and then click Apply. • Resetyourroutertothedefaultsettings.LaunchthewebGUI,go to Administration > Restore/Save/Upload Setting, and click Restore. The default login account and password are both “admin”. How to restore the system to its default settings?• GotoAdministration > Restore/Save/Upload Setting, and click Restore. The following are the factory default settings: User Name: admin Password: admin Enable DHCP: Yes (if WAN cable is plugged in) IP address: 192.168.1.1 Domain Name: (Blank) Subnet Mask: 255.255.255.0 DNS Server 1: 192.168.1.1 DNS Server 2: (Blank) SSID (2.4GHz): ASUS SSID (5GHz): ASUS_5G
112Firmware upgrade failed. Launch the rescue mode and run the Firmware Restoration utility. Refer to section 5.2 Firmware Restoration on how to use the Firmware Restoration utility.
113Cannot access Web GUIA. Disable the proxy server, if enabled.Windows® 71. Click Start > Internet Explorer to launch the browser.2. Click Tools > Internet options > Connections tab > LAN settings.Before configuring your wireless router, do the steps described in this section for your host computer and network clients.3. From the Local Area Network (LAN) Settings screen, untick Use a proxy server for your LAN.4. Click OK when done.
114MAC OS1. From your Safari browser, click Safari > Preferences > Advanced > Change Settings...2. From the Network screen, deselect FTP Proxy and Web Proxy (HTTP).3. Cllick Apply Now when done.NOTE: Refer to your browser's help feature for details on disabling the proxy server.B. Set the TCP/IP settings to automatically obtain an IP address.Windows® 71. Click Start > Control Panel > Network and Internet > Network and Sharing Center > Manage network connections.2. Select Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), then click Properties.
1153. To obtain the IPv4 IP settings automatically, tick Obtain an IP address automatically. To obtain the IPv6 IP settings automatically, tick Obtain an IPv6 address automatically. 4. Click OK when done.MAC OS1. Click the Apple icon located on the top left of your screen.2. Click System Preferences > Network > Configure...3. From the TCP/IP tab, select Using DHCP in the Configure IPv4 dropdown list.4. Cllick Apply Now when done.NOTE: Refer to your operating system’s help and support feature for details on configuring your computer’s TCP/IP settings.
116C. Disable the dial-up connection, if enabled.Windows® 71. Click Start > Internet Explorer to launch the browser.2. Click Tools > Internet options > Connections tab.3. Tick Never dial a connection.4. Click OK when done.NOTE: Refer to your browser's help feature for details on disabling the dial-up connection.
117AppendicesNoticesASUS Recycling/Takeback ServicesASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions.REACHComplying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website athttp://csr.asus.com/english/index.aspxFederal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • Thisdevicemaynotcauseharmfulinterference.• Thisdevicemustacceptanyinterferencereceived,includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
118This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorientorrelocatethereceivingantenna.• Increasetheseparationbetweentheequipmentandreceiver.• Connecttheequipmentintoanoutletonacircuitdierentfrom that to which the receiver is connected.• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.IMPORTANT! This device is restricted for indoor use..WARNING!• Anychangesormodificationsnotexpresslyapprovedbythepartyresponsible for compliance could void the user’s authority to operate the equipment.• Usersmustnotmodifythisdevice.Modificationsbyanyoneotherthan the party responsible for compliance with the rules of the Federal Communications Commission (FCC) may void the authority granted under FCC regulations to operate this device.• ForproductavailableintheUSA/Canadamarket,onlychannel1~11can be operated. Selection of other channels is not possible.
119Prohibition of Co-locationThis device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.Safety InformationThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 31 cm between the radiator and your body.Declaration of Conformity for R&TTE directive 1999/5/ECEssential requirements – Article 3Protection requirements for health and safety – Article 3.1aTesting for electric safety according to EN 60950-1 has been conducted. These are considered relevant and sufficient.Protection requirements for electromagnetic compatibility – Article 3.1bTesting for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-17 has been conducted. These are considered relevant and sufficient.Effective use of the radio spectrum – Article 3.2Testing for radio test suites according to EN 300 328 & EN 301 893 have been conducted. These are considered relevant and sufficient.Operate the device in 5150-5250 MHz frequency band for indoor use only. CE Mark WarningThis is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
120This equipment may be operated in AT, BE, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IE, IT, LU, MT, NL, PL, PT, SK, SL, ES, SE, GB, IS, LI, NO, CH, BG, RO, RT.Canada, Industry Canada (IC) NoticesThis device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Radio Frequency (RF) Exposure InformationThis equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 31 cm between the radiator & your body.Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 31 cm de distance entre la source de rayonnement et votre corps.Canada, avis d’Industry Canada (IC)Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
121WARNING!• This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.• For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.• Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.• This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures.• Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.• The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.• Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intér réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.(3568A-RTGZ00)(3568A-RTGZ00)
122Table for Filled AntennaAnt. Brand Model Name Antenna TypeConnector Gain (dBi)2.4GHz 5GHz band 15GHz band41 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA- - 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA- - 3.33M.gear C660-510331-A Dipole AntennaReversed-SMA3.472 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA- - 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA- - 3.33M.gear C660-510331-A Dipole AntennaReversed-SMA3.473 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA2.6 3.37 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA1.87 3.23 3.334 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA- - 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA- - 3.33M.gear C660-510331-A Dipole AntennaReversed-SMA3.475 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA2.6 3.37 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA1.87 3.23 3.336 PSA RFDPA181300SBLB805 Dipole AntennaReversed-SMA2.6 3.37 2.89M.gear C660-510324-A Dipole AntennaReversed-SMA1.87 3.23 3.33NCC 警語經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
123GNU General Public LicenseLicensing informationThis product includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please see The GNU General Public License for the exact terms and conditions of this license. We include a copy of the GPL with every CD shipped with our product. All future firmware updates will also be accompanied with their respective source code. Please visit our web site for updated information. Note that we do not offer direct support for the distribution.GNU GENERAL PUBLIC LICENSEVersion 2, June 1991Copyright (C) 1989, 1991 Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307 USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use
124pieces of it in new free programs; and that you know you can do these things.To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.The precise terms and conditions for copying, distribution and modification follow.Terms & conditions for copying, distribution, & modification0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may
125be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
126 c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
127 b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to
128modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
129Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing
130and reuse of software generally.NO WARRANTY11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.END OF TERMS AND CONDITIONS
131For Turkey onlyAEEE Yönetmeliğine Uygundur.Authorised distributors in Turkey:BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.Tel. No.: +90 212 3311000Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10 AYAZAGA/ISTANBULCIZGI Elektronik San. Tic. Ltd. Sti.Tel. No.: +90 212 3567070Address: CEMAL SURURI CD. HALIM MERIC IS MERKEZI No: 15/C D:5-6 34394 MECIDIYEKOY/ISTANBULKOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.Tel. No.: +90 216 5288888Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL
132ASUS Contact informationASUSTeK COMPUTER INC. (Asia Pacific)Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259Website www.asus.com.twTechnical SupportTelephone +886228943447SupportFax +886228907698Online support support.asus.comASUS COMPUTER INTERNATIONAL (America)Address 800 Corporate Way, Fremont, CA 94539, USATelephone +15107393777Fax +15106084555Website usa.asus.comOnline support support.asus.comASUS COMPUTER GmbH (Germany and Austria)Address Harkort Str. 21-23, D-40880 Ratingen, GermanySupportFax +49-2102-959931Website asus.com/deOnline contact eu-rma.asus.com/salesTechnical SupportTelephone (Component) +49-2102-5789555Telephone Germany (System/Notebook/Eee/LCD) +49-2102-5789557Telephone Austria (System/Notebook/Eee/LCD) +43-820-240513SupportFax    +49-2102-959911Online support support.asus.com
133Networks Global Hotline InformationRegion Country Hotline Number Service HoursEuropeCyprus 800-92491 09:00-13:00 ; 14:00-18:00 Mon-FriFrance 0033-170949400 09:00-18:00 Mon-FriGermany0049-180501092009:00-18:00 Mon-Fri10:00-17:00 Mon-Fri0049-1805010923(component support)0049-2102959911 ( Fax )Hungary 0036-15054561 09:00-17:30 Mon-FriItaly 199-400089 09:00-13:00 ; 14:00-18:00 Mon-FriGreece 00800-44142044 09:00-13:00 ; 14:00-18:00 Mon-FriAustria 0043-820240513 09:00-18:00 Mon-FriNetherlands/Luxembourg 0031-591570290 09:00-17:00 Mon-FriBelgium 0032-78150231 09:00-17:00 Mon-FriNorway 0047-2316-2682 09:00-18:00 Mon-FriSweden 0046-858769407 09:00-18:00 Mon-FriFinland 00358-969379690 10:00-19:00 Mon-FriDenmark 0045-38322943 09:00-18:00 Mon-FriPoland 0048-225718040 08:30-17:30 Mon-FriSpain 0034-902889688 09:00-18:00 Mon-FriPortugal 00351-707500310 09:00-18:00 Mon-FriSlovak Republic 00421-232162621 08:00-17:00 Mon-FriCzech Republic 00420-596766888 08:00-17:00 Mon-FriSwitzerland-German 0041-848111010 09:00-18:00 Mon-FriSwitzerland-French 0041-848111014 09:00-18:00 Mon-FriSwitzerland-Italian 0041-848111012 09:00-18:00 Mon-FriUnited Kingdom 0044-8448008340 09:00-17:00 Mon-FriIreland 0035-31890719918 09:00-17:00 Mon-FriRussia and CIS 008-800-100-ASUS 09:00-18:00 Mon-FriUkraine 0038-0445457727 09:00-18:00 Mon-Fri
134Networks Global Hotline InformationRegion Country Hotline Numbers Service HoursAsia-PacificAustralia 1300-278788 09:00-18:00 Mon-FriNew Zealand 0800-278788 09:00-18:00 Mon-FriJapan 0800-1232787 09:00-18:00 Mon-Fri09:00-17:00 Sat-Sun0081-570783886( Non-Toll Free )09:00-18:00 Mon-Fri09:00-17:00 Sat-SunKorea 0082-215666868 09:30-17:00 Mon-FriThailand 0066-24011717 09:00-18:00 Mon-Fri1800-8525201Singapore 0065-64157917 11:00-19:00 Mon-Fri0065-67203835 11:00-19:00 Mon-Fri( Repair Status Only ) 11:00-13:00 SatMalaysia 0060-320535077 10:00-19:00 Mon-FriPhilippine 1800-18550163 09:00-18:00 Mon-FriIndia 1800-2090365 09:00-18:00 Mon-SatIndia(WL/NW) 09:00-21:00 Mon-SunIndonesia 0062-2129495000 09:30-17:00 Mon-Fri500128 (Local Only) 9:30 – 12:00 SatVietnam 1900-555581 08:00-12:00 13:30-17:30 Mon-SatHong Kong 00852-35824770 10:00-19:00 Mon-SatAmericasUSA 1-812-282-2787 8:30-12:00 EST Mon-FriCanada 9:00-18:00 EST Sat-SunMexico 001-8008367847 08:00-20:00 CST Mon-Fri08:00-15:00 CST Sat
135NOTE: For more information, visit the ASUS support site at: http://support.asus.comManufacturer: ASUSTeK Computer Inc.Tel: +886-2-2894-3447Address: 4F, No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWANAuthorised representative in Europe:ASUS Computer GmbHAddress: HARKORT STR. 21-23, 40880 RATINGEN, GERMANYRegion Country Hotline Numbers Service HoursMiddle East + AfricaEgypt 800-2787349 09:00-18:00 Sun-ThuSaudi Arabia 800-1212787 09:00-18:00 Sat-WedUAE 00971-42958941 09:00-18:00 Sun-ThuTurkey 0090-2165243000 09:00-18:00 Mon-FriSouth Africa 0861-278772 08:00-17:00 Mon-FriIsrael *6557/00972-39142800 08:00-17:00 Sun-Thu*9770/00972-35598555 08:30-17:30 Sun-ThuBalkan CountriesRomania 0040-213301786 09:00-18:30 Mon-FriBosnia Herzegovina 00387-33773163 09:00-17:00 Mon-FriBulgaria 00359-70014411 09:30-18:30 Mon-Fri00359-29889170 09:30-18:00 Mon-FriCroatia 00385-16401111 09:00-17:00 Mon-FriMontenegro 00382-20608251 09:00-17:00 Mon-FriSerbia 00381-112070677 09:00-17:00 Mon-FriSlovenia 00368-59045400 08:00-16:00 Mon-Fri00368-59045401Estonia 00372-6671796 09:00-18:00 Mon-FriLatvia 00371-67408838 09:00-18:00 Mon-FriLithuania-Kaunas 00370-37329000 09:00-18:00 Mon-FriLithuania-Vilnius 00370-522101160 09:00-18:00 Mon-FriNetworks Global Hotline Information

Navigation menu