ASUSTeK Computer WL330N3G 3G MOBILE WIRELESS ROUTER User Manual

ASUSTeK Computer Inc 3G MOBILE WIRELESS ROUTER Users Manual

Users Manual

3G Mobile Wireless Router(WL-330N3G)User Guide
iiE6069First Edition October 2010Copyright © 2010 ASUSTeK Computer Inc. All Rights Reserved.No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. (“ASUS”).Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe. Offer to Provide Source Code of Certain SoftwareThis product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.Where the applicable license entitles you to the source code of such software and/or other additional data, such data should have been shipped along with this product.You may also download it for free from http://support.asus.com/download.The source code is distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notication to the email address gpl@asus.com, stating the product and describing the problem (please do NOT send large attachments such as source code archives etc to this email address).
iiiTable of contentsNotices .......................................................................................................... vSafety statements ....................................................................................... viREACH ........................................................................................................ viiAbout this guide ....................................................................................... viiiASUS contact information ......................................................................... ixWL-330N3G specications summary ......................................................... xChapter 1: Product introduction1.1 Welcome! ...................................................................................... 1-21.2 Package contents ......................................................................... 1-21.3 Features ........................................................................................ 1-31.3.1 Top view .......................................................................... 1-31.3.2 Bottom view .................................................................... 1-51.3.3 Ports ................................................................................ 1-51.4 Recommended network settings ................................................ 1-61.4.1 Router mode ................................................................... 1-61.4.2 Access Point (AP) mode ................................................. 1-61.4.3 Ethernet Adapter mode ................................................... 1-71.4.4 Repeater mode ............................................................... 1-71.4.5 Hotspot mode .................................................................. 1-71.4.6 3G Sharing mode ............................................................ 1-8Chapter 2: Hardware installation2.1 System requirements ................................................................... 2-22.2 Device installation ........................................................................ 2-22.2.1 Before you proceed ......................................................... 2-22.2.2 Installing the device ........................................................ 2-3Chapter 3: Utilities3.1 Installing the utilities ................................................................... 3-23.1.1 Launching the utilities ..................................................... 3-3Chapter 4: Conguration4.1 Overview ....................................................................................... 4-24.1.1 Adjusting the TCP/IP settings ......................................... 4-2
ivTable of contents4.1.2 Launching the web GUI .................................................. 4-44.2 Operation modes .......................................................................... 4-54.2.1 Router mode ................................................................... 4-54.2.2 Access Point (AP) mode ................................................. 4-64.2.3 Repeater mode ............................................................... 4-84.2.4 Ethernet Adapter mode ................................................... 4-94.2.5 Hotspot mode ................................................................ 4-104.2.6 3G Sharing mode .......................................................... 4-124.3 Advanced setting ....................................................................... 4-134.3.1 Wireless ........................................................................ 4-134.3.2 LAN ............................................................................... 4-284.3.3 WAN .............................................................................. 4-304.3.4 Internet Firewall ............................................................ 4-344.3.5 Administration ............................................................... 4-364.3.6 System Log ................................................................... 4-39Chapter 5: Using the device5.1 Using the device in a local network ........................................... 5-25.2 Replacing the computer Ethernet cables .................................. 5-25.3 Replacing the cable connections of other devices ................... 5-35.4 Sharing Internet connection with other computers .................. 5-3Appendix: Troubleshooting
vNoticesFederal Communications Commission StatementThis device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.CAUTION! Changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.3G USB Adapter Purchase Information• The customer should purchase the 3G USB Adapters which shalle be FCC approved.• 3G USB Adapters must not exceed a maximum ERP of 1.5W for part 22H.• 3G USB Adapters must not exceed a maximum EIRP of 2W for part 24E.
viSafety statementsRegulatory Information/DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modication of this device, or the substitution of the connecting cables and equipment other than the manufacturer specied. It is the responsibility of the user to correct any interference caused by such unauthorized modication, substitution or attachment. Manufacturer and its authorized dealers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. Safety InformationIn order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance [20cm] between the radiator and your body. Use only with supplied antenna.Unauthorized antenna, modication, or attachments could damage the transmitter and may violate FCC regulations.CAUTION! Any changes or modications not expressly approved in this manual could void your authorization to use this device.RF Exposure warningThis equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Ofce of the Federal Register, National Archives and Records Administration, U.S. Government Printing Ofce.
viiMPE StatementYour device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal.Safety statementsCaution Statement of the FCC Radio Frequency ExposureThis Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in a manner that the potential for human contact during normal operation - as a mobile or portable device but use in a body-worn way is strictly prohibited. When using this device, a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance. In order to comply with the RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20cm.RF ExposureThe antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.REACHComplying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://scr.asus.com/english/index.aspx
viiiAbout this guideThis user guide contains information that you need to install and congure your ASUS Portable Wireless AP.How this guide is organizedThis guide contains the following parts:• Chapter 1: Product introduction This chapter describes the physical features of the ASUS Portable Wireless AP. This part also presents the package contents, LED indicators, and recommended network settings. • Chapter 2: Hardware installation This chapter provides information on how to install the ASUS Portable Wireless AP.• Chapter 3: Utilities This chapter provides information on how to configure the ASUS Portable Wireless AP using the utilities available from the support CD.• Chapter 4: Configuration This chapter provides instructions on how to configure the ASUS Portable Wireless AP using the Web Configuration Manager.• Chapter 5: Using the device This chapter provides instructions on how to use the ASUS Portable Wireless AP on various network setups.• Appendix: Troubleshooting The Appendix features a troubleshooting guide for solving common problems you may encounter when using the ASUS Portable Wireless AP.Conventions used in this guideWARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task.NOTE: Tips and additional information to aid in completing a task.
ixASUS contact informationASUSTeK COMPUTER INC.Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259Telephone +886-2-2894-3447Fax +886-2-2890-7798E-mail info@asus.com.twWeb site www.asus.com.twTechnical SupportTelephone +86-21-38429911Online support support.asus.comASUS COMPUTER INTERNATIONAL (America)Address 800 Corporate Way, Fremont, CA 94539, USATelephone +1-510-739-3777Fax +1-510-608-4555Web site usa.asus.comTechnical SupportTelephone +1-812-282-2787Support fax +1-812-284-0883Online support support.asus.comASUS COMPUTER GmbH (Germany and Austria)Address Harkort Str. 21-23, D-40880 Ratingen, GermanyFax +49-2102-959911Web site www.asus.deOnline contact www.asus.de/salesTechnical SupportTelephone (Component) +49-1805-010923*Telephone (System/Notebook/Eee/LCD) +49-1805-010920*Support Fax +49-2102-9599-11Online support support.asus.com* EUR 0.14/minute from a German xed landline; EUR 0.42/minute from a mobile phone.
xWL-330N3G specications summary(continued on the next page)Ethernet Port Wireless Port Power Adapter Buttons SizeWeightWireless NATLAN, 1 x RJ45 for 10/100 BaseT Supports Ethernet and 802.3 with max bit rate 10/100Mbps and auto cross-over function (MDI-X)Transmit Power: 11b 19+-1.5dBm, 11g 17+-1.5 dBm at nominal temperature Receiver Sensitivity: -95+-1dBm@1Mbps, -85+-1dBm@11Mbps, -73+-1dBm@54Mbps Antenna Gain in 1.25dBi 1 x internal IFA antenna Range: Indoor 130ft (40m), semi-open 330ft (100m), outdoor (LOS, Line of Sight) 1500ft (457m) Range and throughput may vary in different environment.AC input: 100V~240V (50~60Hz) DC output: 5V with max 2A currentReset Button: Push for ve seconds to restore to factory default settings90.0mm x 38.9mm x 12.8mm (LxWxH)30g (excluding power adapter and cables)802.11n/802.11g/802.11b compliant Operation Channels: Ch1~11 for N. America, Ch1~14 Japan, Ch1~13 Europe (ETSI) Wi-Fi Security: 64/128-bit WEP, WPA-PSK, WPA2-PSK, WPA- Enterprise, WPA2-Enterprise, Radius with 802.1x WMM: WMM (Wi-Fi Multimedia) support MAC Access Control RADIUS Setting: Required in Radius with 802.1x, WPA, WPA2 mode. Wireless Separation: Prevents wireless clients from communicating with each other.Port Trigger - Opens certain TCP or UDP ports to communicate with the computers connected to the ASUS WL-330N3G. Virtual Server - Provides services like WWW, FTP by a server in the local network accessible for outside users Virtual DMZ - Exposes one computer to the Internet, so that all the inbounds packets are redirected to the computer. ALG: FTP, SIP, VPN Passthrough-IPSec(1), PPTP/L2TP(4)
xiWL-330N3G specications summary• The ASUS Mobile Wireless Router operating distance may be shorter if there are walls, barriers, or interferences in the home layout or operating environment.• Specications are subject to change without notice.• GPL open source is included in the utility CDFirewall RoutingManagement Utility Standard CertificationNAT and SPI (Stateful Packet Inspection) Firewall Filtering - Single Port and Port Range - URL basedStatic RouteInternet connection type: Automatic IP, Static IP, PPPoE (MPPE supported), PPTP, Bigpond Service Support UPnP IGD DHCP Server - Supports up to 253 IP addresses - Changeable DHCP lease time, IP pool, domain name DNS Proxy NTP Client DDNS: DynDNS, ZoneEdit, TZO Web-based Administration - Managed from LAN and Internet - Password Setting System Event Log Firmware Upgrade: Web Interface, Bootloader Save/Restore Conguration FileDevice Discovery, supports Windows 7/ XP/ 2000/ Vista Firmware Restoration, supports Windows 7/ XP/ 2000/ VistaIEEE802.11N, IEEE802.11g, IEEE802.11b, IEEE802.11d, IEEE802.3, IEEE802.3, u, IEEE802.1X, WPA, WMM, IPv4, IPv6WiFi, WPA, WPA2, WMM, UPnP IGD
xii
Product introductionThis chapter describes the physical features of the ASUS Mobile Wireless Router. This part presents the package contents, LED indicators, and recommended network settings.Chapter 1
1-2 Chapter 1: Product introduction1.1 Welcome!Thank you for choosing the ASUS Mobile Wireless Router!The ASUS Mobile Wireless Router is a compact, portable, and easy-to-install device that combines access point (AP), router, universal repeater, Ethernet adapter, hotspot, and 3G sharing functions into one. Implementing the IEEE 802.11n standard for wireless technologies, the ASUS Mobile Wireless Router is capable of up to 150Mbps data transmission rate. This router is backward compatible with the earlier IEEE 802.11g standard allowing seamless interfacing of both wireless LAN standards.The ASUS Mobile Wireless Router also supports several wireless network conguration including AP, Infrastructure, and Ad-hoc modes giving you exibility on your existing or future wireless network congurations.To provide efcient security to your wireless communication, ASUS Mobile Wireless Router comes with a 64-bit/128-bit Wired Equivalent Privacy (WEP) encryption and Wi-Fi Protected Access (WPA) features.1.2 Package contentsCheck the following items in your ASUS Mobile Wireless Router package. Contact your retailer if any item is damaged or missing. ASUS Mobile Wireless Router (WL-330N3G) Universal power adapter and plug (100V ~ 240V) Micro USB power cord RJ45 cable Support CD (manual, utilities, GPL) Quick Start Guide
1-3ASUS WL-330N3G Mobile Wireless Router1.3 Features• Data transfer rate up to 150Mbps• Secure data transmission via Wired Equivalent Privacy (WEP) and WiFi Protected Access (WPA) encryptions• Operating distance of up to 130ft (40m) indoors and 1000 ft (310m) outdoors• Dual power mode (DC or Micro USB bus-powered)• Supports Infrastructure and Ad-hoc network types in Ethernet adapter mode• Windows® 98SE/Me/2000/XP/Vista/7 compatible1.3.1 Top viewThe ASUS Mobile Wireless Router comes with 3G, Ethernet, Wireless, and Power LED indicators. Refer to the table below for LED indicatorsLED Status Mode* Indication3G On (Blue) On (Red) OffFlashing3G sharing The USB 3G adapter is connected. (Connect the power adapter to the mobile wireless router.) The USB 3G adapter is connected. (Connect the USB connector to a USB port on your computer.)No USB 3G adapter is connected.3G sharing is working.
1-4 Chapter 1: Product introduction*Modes: AP: Access Point mode EA: Ethernet adapter mode URE: Universal repeater modeLED Status Mode* IndicationEthernet OnOffRouter/AP/EA/UREThe RJ-45 cable is connected and the mobile wireless router is connected to an Ethernet network.The mobile wireless router is off or is not connected to an Ethernet network.Wireless OnFlashingOffRouter/AP/UREEAEARouter/AP/UREEAAssociated.Associated with an AP.Associating.Not associated.Associated with an AP.Power OnFlashingOffRouter/AP/EA/URERouter/AP/EA/URERouter/AP/EA/UREThe mobile wireless router is on and ready.The mobile wireless router is under “reset to default” mode.The device is off.
1-5ASUS WL-330N3G Mobile Wireless Router1.3.2 Bottom viewReset button: Press and hold for more than five seconds to load the default values. Air vents: These vents provide ventilation to the device.1.3.3 PortsEthernet port: This port connects the bundled RJ-45 cable.Micro USB port: This port connects the power adapter plug or the bundled micro-USB cable.USB port: This port connects USB devices.Reset buttonAir ventsEthernet portMicro USB portUSB port
1-6 Chapter 1: Product introduction1.4 Recommended network settingsInternet Hub˝Network PrinterClient 1Client 2Client 3Client 4WL-330N3GMODE1.4.2 Access Point (AP) modeWhen in access point (AP) mode the WL-330N3G connects WLAN-enabled computers and devices to a wired or wireless LAN.Wireless computer Internet˝ADSL/Cable modemWL-330N3GIn the Quick Setup Wizard, you can only congure WEP for security (open system). You can complete the share key and advanced security setup in the Advanced Settings page.The ASUS Mobile Wireless Router can be congured in one of these modes: 1. Router mode 4. Repeater mode 2. Access Point (AP) mode 5. Hotspot mode 3. Ethernet Adapter mode 6. 3G sharing mode By default, the ASUS WL-330N3G is set in the Router mode.1.4.1 Router modeIn the Router mode, the ASUS WL-330N3G connects to the Internet via an ADSL or a cable modem, and your network environment has multi-users using the same IP to ISP.
1-7ASUS WL-330N3G Mobile Wireless Router1.4.3 Ethernet Adapter modeIn the Ethernet Adapter mode, you can enable any Ethernet-capable device to go wireless.1.4.4 Repeater modeIn the Repeater mode, you can use the ASUS WL-330N3G to connect with your root router at home to extend your wireless coverage.Internet˝WL-330N3GInternet˝WL-330N3G1.4.5 Hotspot modeIn Hotspot mode, WL-330N3G connects front-end base stations wirelessly and obtains WAN IP to an Internet connection. It provides you with wireless radio signal.WL-330N3G Internet˝
1-8 Chapter 1: Product introduction1.4.6 3G Sharing modeIn 3G Sharing mode, you are allowed to share 3G Internet connection among other Wi-Fi available devices. Internet˝WL-330N3G3G USB Adapter
Hardware installationThis chapter provides information on how to install the ASUS Mobile Wireless Router.Chapter 2
2-2 Chapter 2: Hardware installation2.1 System requirementsBefore installing the ASUS Mobile Wireless Router, make sure that your system/network meets the following requirements:• An Ethernet RJ-45 port (10-100Base-T)• At least one IEEE 802.11b/g/n device with wireless capability• An installed TCP/IP and Internet browser2.2 Device installationFollow these instructions to install the ASUS Mobile Wireless Router.1. Install the device utilities from the support CD.2. Connect the device to your computer, network hub, switch, or router.2.2.1 Before you proceedTake note of the following guidelines before installing the ASUS Mobile Wireless Router.• The length of the Ethernet cable that connects the device to the network (hub, ADSL/cable modem, router, wall patch) must not exceed 100 meters.• Place the device on a flat, stable surface as far from the ground as possible.• Keep the device clear from metal obstructions and away from direct sunlight.• Keep the device away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators, and other industrial equipment to prevent signal loss.• Install the device in a central area to provide ideal coverage for all wireless mobile devices.• Install the device at least 20cms from a person to insure that the product is operated in accordance with the RF Guidelines for Human Exposure adopted by the Federal Communications Commission.
2-3ASUS WL-330N3G Mobile Wireless Router2.2.2 Installing the device1. Insert one end of the supplied RJ-45 cable to the WL-330N3G Ethernet port.2. Insert the other end of the RJ-45 cable to your computer.3. Do either of the following:A Connect the power adapter plug to the WL-330N3G DC-IN socket and connect the power adapter to a wall socket (A). Connect the USB power cord plug to the WL-330N3G DC-IN socket and connect the USB connector into your computer’s USB port (B). B
2-4 Chapter 2: Hardware installation
UtilitiesThis chapter provides information on how to congure the ASUS Mobile Wireless Router using the utilities available from the support CD.Chapter 3
3-2 Chapter 3: Utilities3.1 Installing the utilitiesThe support CD contains the utilities for conguring the ASUS Mobile Wireless Router. To install the ASUS WLAN Utilities in Microsoft® Windows, insert the support CD in the CD drive. If Autorun is disabled, run setup.exe from the root directory of the support CD.2. Click Next.3. Click Next to accept the default destination folder or click Browse to specify another path.4. Click Next to accept the default program folder or enter another name.1. Click Install...Utilities.5. Click Finish when setup is complete.
3-3ASUS WL-330N3G Mobile Wireless Router3.1.1 Launching the utilitiesTo launch the utilities, click Start > All Programs > ASUS Utility from the Windows desktop.Device DiscoveryDevice Discovery is an ASUS WLAN utility which detects an ASUS device, and enables you to congure the device.To launch the Device Discovery utility, click Start > All Programs > ASUS Utility > Device Discovery.
3-4 Chapter 3: UtilitiesFirmware RestorationThe Firmware Restoration utility is an emergency rescue tool that automatically searches for an ASUS Router that has failed during a rmware upload, and re-upload a rmware that you specify. A failed rmware upgrade will cause the ASUS Router to enter a failure mode, waiting for the Firmware Restoration utility to nd and upload a new rmware. The process takes about three to four minutes.This is not a rmware upgrade utility and cannot be used on a working ASUS Router. Normal rmware upgrades must be done through the web manager. Refer to Chapter 4: Conguration for more details.To launch the Firmware Restoration utility, click Start > All Programs > ASUS Utility > Firmware Utility.
CongurationThis chapter provides instructions on how to congure the ASUS Mobile Wireless Router using the web graphics user interface (web GUI).Chapter 4
4-2 Chapter 4: Configuration4.1 OverviewThe web graphics user interface (web GUI) allows you to congure the ASUS Mobile Wireless Router using a web browser on your computer. 4.1.1 Adjusting the TCP/IP settingsBy default, the IP address of the ASUS Mobile Wireless Router is 192.168.1.1, and the Subnet Mask is 255.255.255.0. To access the conguration utility, assign a different IP address to the network adapter where the ASUS Mobile Wireless Router is connected.To adjust the TCP/IP settings of the network adapter:1. Right-click the My Network Places icon in the Windows® desktop, then select Properties from the pop-up menu. The Network and Dial-up Connections window appears.2. Right-click the network adapter used by the the ASUS Mobile Wireless Router, then select Properties from the pop-up menu. The Local Area Connection Properties window appears.
4-3ASUS WL-330N3G Mobile Wireless Router3. Double-click the Internet Protocol (TCP/IP) item to display the Internet Protocol (TCP/IP) Properties window.4. Check the Use the following IP address option, then enter the IP address for the network adapter. The IP address must be 192.168.1.X. (X can be any number between 2 and 254 that is not used by another device.)5. Set the Subnet Mask to 255.255.255.0. Click OK when nished.Changing the TCP/IP settings may require system restart. Switch on the WL-330N3G immediately after rebooting.
4-4 Chapter 4: Configuration4.1.2 Launching the web GUITo launch the web GUI:1. In your web browser, enter 192.168.1.1. The login screen appears.2. Use admin as the username and password. The Setup Wizard is then displayed. The Setup Wizard displays six (6) Operation modes that you can congure using the Web Conguration Manager. Refer to the next section 4.2 Operation modes for more details.
4-5ASUS WL-330N3G Mobile Wireless Router4.2 Operation modesThe ASUS WL-330N3G is designed with six selective operation modes: Router, Access Point (AP), Ethernet Adapter, Repeater, Hotspot, and 3G Sharing.4.2.1 Router modeIn the Router mode, the ASUS WL-330N3G connects to the Internet via an ADSL or a cable modem, and your network environment has multi-users using the same IP to ISP.Wireless computer Internet˝ADSL/Cable modemWL-330N3GIn the Router mode:• NAT is enabled,• WAN is allowed using PPPoE, DHCP client, or static IP,• UPnP and DDNS features, which are useful for home user, are supported.To congure the ASUS WL-330N3G in Router mode:1. Click the Router tab. The Router page appears. Disable your PC’s proxy settings when using the web GUI. Ensure the WL-330N3G and your PC are under the same subnet. Check the Internet protocol (TCP/IP) settings of your local area connection.
4-6 Chapter 4: Configuration2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.3. Select a security level to enable encryption methods: Low (Open System) Medium (WEP-64bits) Medium (WEP-128 bits) High (WPA-Personal)4. Click Apply to save the settings.For more details on setting up the advanced functions, refer to the section 4.3 Advanced Setting.4.2.2 Access Point (AP) modeIn the Access Point (AP) mode, you can connect the Ethernet port and your wireless devices into the same local area network (LAN).Wireless computer WL-330N3GTo congure the ASUS WL-330N3G in Access Point/AP mode:1. Click the Access Point tab. The Access Point (AP) page appears. After setting the ASUS WL-330N3G in Router mode, you need to connect the WL-330N3G’s LAN port to an ADSL modem through Windows® Zero Conguration or your wireless card utility on your PC.
4-7ASUS WL-330N3G Mobile Wireless Router2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.3. Select a security level to enable encryption methods: Low (Open System) Medium (WEP-64bits) Medium (WEP-128 bits) High (WPA-Personal)4. Click Apply to save the settings.For more details on setting up the advanced functions, refer to the section 4.3 Advanced Setting.
4-8 Chapter 4: ConfigurationTo congure the ASUS WL-330N3G in Repeater mode:1. Click the Universal Repeater tab. The Universal Repeater page appears. 4.2.3 Repeater modeIn the Repeater mode, the ASUS WL-330N3G extends your wireless network coverage.WL-330N3G Internet˝2. From the available list of devices in LAN, select the device you want to connect to. You may add a device if you cannot nd the device you want to connect to in the list. Refer to To add a device to the list.3. Click Connect.To add a device to the list:1. In the Universal Repeater page, click Add. The Add Preferred Wireless Network pop-up window appears.2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.
4-9ASUS WL-330N3G Mobile Wireless Router4.2.4 Ethernet Adapter modeIn the Ethernet Adapter mode, you can enable any Ethernet-capable device to go wireless.WL-330N3G Internet˝To congure the ASUS WL-330N3G in Ethernet Adapter mode:1. Click the Ethernet Adapter tab. The Ethernet Adapter page appears. 2. From the available list of devices in LAN, select the device you want to connect to. You may add a device if you cannot nd the device you want to connect to in the list. Refer to To add a device to the list.For more details on setting up the advanced functions, refer to the section 4.3 Advanced Setting.3. Select an authentication method: Open System Shared system WPA-Personal WPA2-Personal4. Click Connect. The device will now be displayed in the list.
4-10 Chapter 4: Configuration4.2.5 Hotspot modeIn Hotspot mode, WL-330N3G connects front-end base stations wirelessly and obtains WAN IP for an Internet connection. It provides you with wireless radio signal.For more details on setting up the advanced functions, refer to the section 4.3 Advanced Setting.3. Click Connect.To add a device to the list:1. In the Adapter page, click Add. The Add Preferred Wireless Network pop-up window appears.2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.3. Select an authentication method: Open System Shared system WPA-Personal WPA2-Personal4. Click Connect. The device will now be displayed in the list.WL-330N3G Internet˝
4-11ASUS WL-330N3G Mobile Wireless Router2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.3. Select a security level to enable encryption methods.4. From the available list of devices, select the device you want to connect to. You may add a device if you cannot nd the device you want to connect to in the list. Refer to To add a device to the list.5. Click Connect.To add a device to the list:1. In the Hotspot page, click Add. The Add Preferred Wireless Network pop-up window appears.2. Specify a network name or SSID (Service Set Identier), which is a unique identier attached to packets sent over WLAN.3. Select an authentication method: Open System Shared system WPA-Personal WPA2-Personal4. Click Connect. The device will now be displayed in the list.To congure the ASUS WL-330N3G in Hotspot mode:1. Click the Hotspot tab. The Hotspot page appears.
4-12 Chapter 4: Configuration4.2.6 3G Sharing modeIn 3G Sharing mode, you are allowed to share 3G Internet connection with other Wi-Fi available devices. Internet˝WL-330N3G3G USB AdapterTo congure the ASUS WL-330N3G in 3G Sharing mode:1. Click the 3G Sharing tab. The 3G Sharing page appears. 2. Congure the following settings: Enable HSDPA: Select Enable. 3G/3.5G USB Adapter: Select your 3G USB adapter. Location: Select your ISP’s location. ISP: Select your ISP. APN service (optional): Key in your APN service name. PIN: Key in the PIN (Personal Identication Number) code. Dial Number: Key in your dial number.
4-13ASUS WL-330N3G Mobile Wireless Router Username: Key in your username. Password: Key in your password. * Obtain the APN service name, PIN code, dial number, username, and password from your ISP.3. Click Apply.4.3 Advanced settingWhen you click the link Advance Setting from any of the modes, the screen shown below is displayed.4.3.1 WirelessClick an item on the page and follow the instructions to set up the ASUS WL-330N3G.
4-14 Chapter 4: ConfigurationInterfaceSSIDThe SSID is an identication string of up to 32 ASCII characters that differentiate the ASUS WL-330N3G from other manufacturers. The SSID is also referred to as the “ESSID” or “Extended Service Set ID.” You can use the default SSID and radio channel unless more than one WL-330N3G is deployed in the same area. In that case, you should use a different SSID and a radio channel for each WL-330N3G. All ASUS Wireless APs/Routers and ASUS 802.11n/802.11g/802.11b WLAN client adapters must have the same SSID to allow a wireless mobile client to roam. By default, the SSID is set to “ASUS”.Wireless ModeThis eld indicates the 802.11g interface mode. Selecting “Auto” allows 802.11g and 802.11b clients to connect to the ASUS 802.11g AP. Selecting “54g Only” maximizes performance, but prevents 802.11b clients from connecting to the ASUS 802.11g AP. Selecting “802.11B only” allows only 802.11b clients to connect to the ASUS 802.11g AP. If “54g Protection” is checked, GMode protection of 11g trafc is enabled automatically in the presence of 11b trafc.ChannelThe 802.11n/802.11g/802.11b specications supports up to 14 overlapping channels for radio communication. To minimize interference, congure each ASUS WL-330N3G to be non-overlapping; select Auto from the Channel drop-down list to enable the system to select a clear channel during boot up as your operating channel.
4-15ASUS WL-330N3G Mobile Wireless RouterBased on your site survey of your network facility, make sure that all the ASUS WL-330N3G sharing the same channel, or channels in close number frequency, are located far from each other as possible. You can use the site survey utility from the support CD. Refer to 3.7.2 Site Survey (AP SCAN) for details.Authentication MethodThis eld enables you to set different authentication methods which determine different encryption schemes. The relationships among Authentication Method, WPA Encryption, WPA Pre-Shared Key, WEP Encryption, Passphrase, and WEP Keys are listed in the following table. If all your clients support WPA, using “WPA-PSK” is recommended for better security.Authentication MethodWPA/WEP EncryptionWPA Pre-Shared Key PassphraseWEP Key 1-4Open System NoneWEP (64 bits)WEP (128 bits)Not required1-64 characters1-64 charactersNot required10 hex26 hexShared key WEP (64 bits)WEP (128 bits)1-64 characters1-64 characters10 hex26 hexWPA-Personal TKIP+AES 8-63 characters Not requiredWPA2-Personal TKIP+AES 8-63 characters Not requiredWPA-Auto-Personal TKIP/AES/ TKIP+AES 8-63 characters Not requiredWPA-Enterprise TKIP 8-63 characters Not requiredWPA2-Enterprise AES 8-63 characters Not requiredRadius with 802.1x AutoWEP (64 bits)WEP (128 bits)Not required1-64 characters1-64 charactersNot required10 hex26 hexWPA EncryptionWhen “WPA-Personal”, “WPA2-Personal”, or “WPA-Auto-Personal” authentication method is used, TKIP (Temporal Key Integrity Protocol) and AES encryption schemes are applied.When “WPA-Enterprise” authentication method is selected, TKIP encryption scheme is applied.When “WPA2-Enterprise” authentication method is selected, AES encryption method is applied.WPA Pre-Shared KeySelect “TKIP” or “AES” in the WPA Encryption, this eld is used as a password to begin the encryption process. 8 to 63 characters are required.
4-16 Chapter 4: ConfigurationWEP EncryptionWhen “Open System”, “Shared Key” or “Radius with 802.1x” authentication methods are selected, traditional WEP encryption is applied.When “WPA” or “WPA-PSK” authentication methods are selected, you still can set WEP encryption for those clients that do not support WPA/WPA-PSK. Please note that Key Index for WEP key is limited to 2 or 3 when both WPA and WEP encryption are supported at the same time.64/128-bit versus 40/104-bitThe following section explains low-level (64-bit) and high-level (128-bit) WEP Encryption schemes:64-bit WEP Encryption64-bit WEP and 40-bit WEP are the same encryption methods and can interoperate in a wireless network. This level of WEP encryption uses a 40-bit (10 Hex character) encryption scheme as a secret key, which is set by the user, and a 24-bit “Initialization Vector” scheme, which is not under user control.Together these two schemes make a 64-bit (40 + 24) encryption scheme. Some vendors refer to this level of WEP as 40-bit and others refer to this as 64-bit. ASUS WLAN products use the term 64-bit when referring to this lower level of encryption.128-bit WEP Encryption104-bit WEP and 128-bit WEP are the same encryption method and can interoperate on a wireless network. This level of WEP encryption uses a 104-bit (26 Hex character) encryption scheme as a secret key which is set by the user, and a 24-bit “Initialization Vector”, which is not under user control.Together these two schemes make a 128-bit (104 + 24) encryption scheme. Some vendors refer to this level of WEP as 104-bit and others refer to this as 128-bit. ASUS WLAN products use the term 128-bit when referring to this higher level of encryption.PassphraseSelect “WEP-64bits” or “WEP-128bits” in the Encryption eld, and the Access Point generates four WEP keys automatically. A combination of up to 64 letters, numbers, or symbols is required. Alternatively, leave this eld blank and type in four WEP keys manually. WEP-64bit key: 10 hexadecimal digits (0~9, a~f, and A~F) WEP-128bit key: 26 hexadecimal digits (0~9, a~f, and A~F)The ASUS WLAN family of products uses the same algorithm to generate WEP keys. It eliminates the need for users to remember passwords and maintains compatibility between products. But, this method to generate WEP keys is not as secure as manual assignment.
4-17ASUS WL-330N3G Mobile Wireless RouterWEP KeyYou can set a maximum of four WEP keys. A WEP key is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) based on whether you select 64-bits or 128-bits in the WEP pull-down menu. The ASUS WL-330N3G and ALL of its wireless clients MUST have at least the same default key.Key IndexThe Default Key eld lets you specify which of the four encryption keys to use to transmit data on your wireless LAN. As long as the ASUS WL-330N3G or wireless mobile client with which you are communicating has the same key in the same position, you can use any of the keys as the default key.If the ASUS WL-330N3G and ALL of its wireless clients use the same four WEP keys, select “key rotation” to maximize security. Otherwise, choose one key in common as the default key.Network Rotation Key IntervalThis eld species the time interval (in seconds) after which a WPA group key is changed. Enter ‘0’ (zero) to indicate that a periodic key-change is not required.WPSWi-Fi Protected Setup (WPS) allows you to set up a secure and protected wireless network easily. You can congure WPS via PIN code method.WPS supports the authentication of Open system, WPA-Personal, and WPA2-Persional, but does not support Shared Key, WPA-Enterprise, WPA2-Enterprise, and Radius.To remove the Client PIN Code you set, press the Reset button at the bottom of the device
4-18 Chapter 4: ConfigurationNote:• Ensure that you use a wireless LAN adapter with WPS function.• Windows® operating systems and wireless LAN cards/adapters that support WPS: Using WPS WizardOS Support Wireless Adapter Support Vista 32/64Intel wireless LAN cardASUS 167gv2 driver v3.0.6.0 or laterASUS 160N/130N driver v2.0.0.0 or later XP SP2Intel wireless LAN cardASUS 167gv2 driver v1.2.2.0 or laterASUS 160N/130N driver v1.0.4.0 or later XP SP1 and 2000ASUS LAN card with ASUS WLAN UtilityASUS 167gv2 driver v1.2.2.0 or laterASUS 160N/130N driver v1.0.4.0 or laterTo use WPS Wizard:1. Follow the onscreen instructions to set up your hardware. When done, click Next.Note: Use the WPS Wizard with one wireless client at a time. If the wireless client cannot discover the wireless router, shorten the distance between the client and the router.
4-19ASUS WL-330N3G Mobile Wireless Router2. Press the WPS button on your router.WPS button3. On the WPS Wizard, click Next to continue.Notes: • When running WPS, the Internet connection pauses briey then reestablishes the connection. • If the WPS button is pushed without running the WPS Wizard, the PWR indicator ashes and Internet connection pauses briey and then reestablishes the connection.
4-20 Chapter 4: Configuration4. Key in desired network name or SSID (service set identier). When done, click Next.5. Create and key in a passphrase consisting of 8-63 characters or use the automatically generated passphrase then click Next. A passphrase is a sentence, phrase, or sequence of alpha-numeric characters used to generate a security key.
4-21ASUS WL-330N3G Mobile Wireless Router6. When nished, click Save or print settings for future reference or Save settings to a USB ash drive to add other devices to the network. Click Next to connect to the Internet.7. You have connected to the wireless router. If you want to congure the Internet settings, click Setup. Click Finish to close the WPS Wizard.Note: For more details on adding devices to the network using a USB ash drive, refer to the section Adding network devices using a USB ash drive on the next page.
4-22 Chapter 4: ConfigurationAdding network devices using a USB ash driveWith the WPS utility, you can add devices to your network using a USB ash drive.To add network devices using a USB ash drive:1. In the WPS Wizard, click Save settings to a USB ash drive.2. Insert a USB ash drive into your computer's USB port, then select the drive from the dropdown list. When done, click Next.
4-23ASUS WL-330N3G Mobile Wireless Router3. Unplug the USB flash drive from your computer then insert it to the other computer that you want to add to your wireless network.4. Locate SetupWireless.exe from the USB drive, and double-click to run it. Click Yes to add the computer to the wireless network.5. Click OK to exit the Wireless Network Setup Wizard.
4-24 Chapter 4: ConfigurationWireless MAC FilterPull down menu items:Disable (no info required)Accept (need to input information)Reject (need to input information)For security, the ASUS WL-330N3G allows you to accept or reject wireless mobile clients.The default setting of “Disable” allows any wireless mobile client to connect. “Accept” only allows those entered into this page to connect. “Reject” prevents those entered into this page from connecting.Adding a MAC AddressThe Known Client List collects MAC addresses of known clients, associated to the AP. To add a MAC address to the Access Control List, enter MAC address, then click “Add” button. Note: Click the “Apply” button to save your new settings and restart the ASUS WL-330N3G or click “Apply” and restart later.
4-25ASUS WL-330N3G Mobile Wireless RouterRADIUS SettingNote: Click the “Apply” button to save your new settings and restart the ASUS WL-330N3G or click “Apply” and restart later.This section allows you to set up additional parameters for connection through the RADIUS Server. It is required that you select either “WPA-Enterprise/WPA2-Enterprise” or “Radius with 802.11x” as Authentication Method in Wireless -> General page.Server IP Address - This eld species the IP address of the RADIUS server to use for 802.1X wireless authentication and dynamic WEP key derivation.Server Port - This eld species the UDP port number used by the RADIUS server.Connection Secret - This eld species the password used to initialize a RADIUS connection.
4-26 Chapter 4: ConfigurationProfessionalThis section allows you to set up additional parameters for the wireless router function. We recommend that you use the default values for all items in this window. Enable Radio - This eld allows you to enable or disable Radio function. “Yes” is the default option.Date to Enable Radio - Schedule the date when you want to enable the Radio function.Time of Day to Enable Radio - Set the exact time on the scheduled date when you want to enable the Radio function. Set AP Isolated - Selecting “Yes” to prevent wireless client from communicating with each other.Multicast Rate (Mbps) - This eld allows you to specify the transmission rate. Leave on “Auto” to maximize performance versus distance.Basic Rate Set - This eld indicates the basic rates that wireless clients must support. Use “1 & 2 Mbps” only when backward compatibility is needed for some older wireless LAN cards with a maximum bit rate of 2Mbps.Fragmentation Threshold (256-2346) – Fragmentation is used to divide 802.11 frames into smaller pieces (fragments) that are sent separately to the destination. Set a specic packet size threshold to enable fragmentation. If there is an excessive number of collisions on the WLAN, experiment with different fragmentation values to increase the reliability of frame transmissions. The default value (2346) is recommended for normal use.RTS Threshold (0-2347) – The RTS/CTS (Request to Send/Clear to Send) function is used to minimize collisions among wireless stations. When RTS/CTS is enabled, the router refrains from sending a data frame until another RTS/CTS handshake is completed. Set a specic packet size threshold to enable RTS/CTS. The default value (2347) is recommended.
4-27ASUS WL-330N3G Mobile Wireless RouterDTIM Interval (1-255) – DTIM (Delivery Trafc Indication Message) is a wireless message used to inform clients in Power Saving Mode when the system should wake up to receive broadcast and multicast messages. Type the time interval in which the system will broadcast a DTIM for clients in Power Saving Mode. The default value (3) is recommendedBeacon Interval (1-65535) – This eld indicates the time interval in milliseconds that a system broadcast packet, or beacon, is sent to synchronize the wireless network. The default value (100 milliseconds) is recommended.Enable TX Bursting – This eld allows you to enable TX-bursting mode to improve performance with wireless clients that also support TX-bursting.Radio Power – Radio Power can be set between 1 to 84 but the default value is recommended.Enable Packet Aggregation - This eld allows you to enable Packet Aggregation.Enable Greeneld - This eld allows you to enable Greeneld.Enable WMM – This eld allows you to enable WMM to improve multimedia transmissionEnable WMM No-Acknowledgement – This eld allows you to enable WMM No-Acknowledgement.Enable WMM APSD - This eld allows you to enable WMM APSD.Enable WMM DLS - This eld allows you to enable WMM DLS.
4-28 Chapter 4: Configuration4.3.2 LANClick this item on the menu and follow the instructions to setup the ASUS WL-330N3G. LAN IPThis page allows you to congure the LAN IP of WL-330N3G. The DHCP Server dynamically changes the IP pool when you change the LAN IP.
4-29ASUS WL-330N3G Mobile Wireless RouterDHCP ServerThe ASUS WL-330N3G supports up to 253 IP addresses for your local network. The IP address of a local machine can be manually assigned by the network administrator or obtained automatically from WL-330N3G if the DHCP server is enabled.RouteThis function allows you to add routing rules into the ASUS WL-330N3G. It is useful if you connect several routers behind WL-330N3G to share the same connection to the Internet.
4-30 Chapter 4: ConfigurationInternet ConnectionWL-330N3G supports several connection types to WAN. The settings elds differ depending on the connection type you selected.4.3.3 WANClick this item on the menu and follow the instructions to setup the ASUS WL-330N3G.
4-31ASUS WL-330N3G Mobile Wireless RouterQoSThis function allows you to set priority for each IP address.Port TriggerThis function allows you to open certain TCP or UDP ports to communicate with the computers connected to the ASUS WL-330N3G. This is done by dening trigger ports and incoming ports. When the trigger port is detected, the inbound packets to the specied incoming port numbers are redirected to your computer.
4-32 Chapter 4: ConfigurationVirtual ServerVirtual Server allows you to make services, like WWW, FTP, provided by a server in your local network accessible for outside users. Virtual DMZThis function allows you to expose a computer to the Internet, so that all inbound trafcs will be redirected to the computer you set. It is useful when you run some applications that use uncertain incoming ports.Use this function carefully.
4-33ASUS WL-330N3G Mobile Wireless RouterDDNSThis function allows you to assign an Internet domain name tto a computer with a dynamic IP address. Currently, several DDNS services are embeded in WL-330N3G.
4-34 Chapter 4: Configuration4.3.4 Internet FirewallGeneralThis function allows you to congure the basic security for your WL-330N3G and other devices connected to it.If you want to lter out specic packets, refer to the next section LAN to WAN Filter.LAN to WAN FilterThis function allows you to block specic packets between LAN and WAN. First, you should dene the date and time that ltering will take place. Next, you should select the default action for lter in both directions and insert rules for any exceptions.
4-35ASUS WL-330N3G Mobile Wireless RouterURL FilterThis function allows you to block specic URL access from your local network.MAC FilterThis function allows you to block specic URL access from your local network.
4-36 Chapter 4: Configuration4.3.5 AdministrationClick this item on the menu and follow the instructions to setup the ASUS WL-330N3G. SystemThis function allows you to change your password and congure other settings such as Remote Log Server, Time Zone, and NTP Server.
4-37ASUS WL-330N3G Mobile Wireless RouterFirmware UpgradeThis page reports the Flash Code (Firmware) version installed in the ASUS WL-330N3G. Periodically, a new Flash Code is available for the ASUS WL-330N3G on ASUS’s Web site. You can update the ASUS WL-330N3G’s Flash Code using the Firmware Upgrade page under the Administration menu of the Web Manager. If you are experiencing a problem with your ASUS WLAN equipment, a Technical Support representative may ask you to give your device’s Flash Code (Firmware) version.Note: The rmware upgrade takes approximately 60 to 90 seconds. When the rmware upgrade is completed, you will be directed to the home page.
4-38 Chapter 4: ConfigurationRestpre/Save/Upload SettingThis function allows you to save current settings to a le, or load settings from a le. You can also restore the settings to the factory default settings.Note: You can also reset all settings to their factory defaults manually by pushing the “Reset” button on the ASUS WL-330N3G while it is ON. Push the “Reset” button with a pen or a paper clip for about 5 seconds or until the power LED starts blinking.
4-39ASUS WL-330N3G Mobile Wireless Router4.3.6 System LogClick this item on the menu to view related information about the ASUS WL-330N3G. General LogDHCP Leases
4-40 Chapter 4: ConfigurationWireless LogPort ForwardingRouting Table
Using the deviceThis chapter provides instructions on how to use the ASUS Mobile Wireless Router on various network setups.Chapter 5
5-2 Chapter 5: Using the deviceUse the Wireless Setting Utility to change the WL-330N3G SSID or encryption settings.5.1 Using the device in a local networkYou can use the WL-330N3G to connect a wireless LAN-enabled computer to a local network with or without a DHCP server.To connect a wireless LAN-enabled computer to a local network:1. Switch the WL-330N3G to AP mode (Default SSID: ASUS).2. Connect one end of the supplied RJ-45 cable to the Ethernet port of the device and the other end to the Ethernet port of the local network.3. Use the wireless LAN adapter software in the wireless LAN-enabled computer to perform a Site Survey. 4. Establish connection with the WL-330N3G.5. Set the IP conguration of the computer to establish connection to the local network. Verify your connection.5.2 Replacing the computer Ethernet cablesYou can use the WL-330N3G to replace your wireless LAN-enabled computer cable connection to an ADSL or cable modem.To do this:1. Switch the WL-330N3G to AP mode. (Default SSID: ASUS), then turn on the device.2. Connect one end of the supplied RJ-45 cable to the Ethernet port of the device and the other end to the Ethernet port of the ADSL or cable modem.3. Use the wireless LAN adapter software in the wireless LAN-enabled computer to perform a Site Survey. 4. Establish connection with the WL-330N3G.5. Set the IP configuration of the computer to establish connection to the local network. Verify your connection.
5-3ASUS WL-330N3G Mobile Wireless Router5.3 Replacing the cable connections of other devicesYou can also use the WL-330N3G to replace your Xbox, PlayStation® 2, orset-top box network cable connection.To do this:1. Switch the WL-330N3G to Ethernet adapter mode using the mode switch. (Default SSID: ANY)2. Place the WL-330N3G nearest the AP you wish to connect, then turn on the device.3. Connect one end of the supplied RJ-45 cable to the Ethernet port of the device and the other end to the Xbox, PlayStation® 2, or set-top box Ethernet port.4. Set the IP address of the Xbox, PlayStation® 2, or set-top box toestablish connection to the local network. Verify your connection.Make sure the WL-330N3G MAC cloning feature is enabled when using the device in this setup. Use the Wireless Setting Utility to enable MAC cloning.5.4 Sharing Internet connection with other computersRefer to the typical network conguration below and the table on the next page for information on Internet connection sharing with other computers in your ofce or home network.Set the WL-330N3G to AP mode before sharing an Internet connection with other computers in your network.Wireless computerInternet˝ADSL/Cable modem WL-330N3G
5-4 Chapter 5: Using the deviceIf your Internet connection isThen set the IP of other computer(s)Number of allowed Internet connectionsxDSL1 with dynamic IP (PPPoE2 account) ISP automatically assigns the IP (using PPPoE dial-up)Depends on the Internet Service Provider (ISP)xDSL with static IP to the provided static IP Depends on the Internet Service Provider (ISP)xDSL/Cable with a router and enable DHCP3 serverThe DHCP server automatically assigns the IPDepends on the DHCP server, usually about 253Table 4-1: Internet connection sharing matrix1xDSL - ADSL (Asymmetric Digital Subscriber Line) or DSL (Digital Subscriber Line)2PPPoE - Point-to-Point over Ethernet3DHCP - Dynamic Host Configuration Protocol
TroubleshootingThe Appendix features a troubleshooting guide for solving common problems you may encounter when using the ASUS Mobile Wireless Router.Appendix
A-2 Appendix: TroubleshootingThis troubleshooting guide provides solutions to some common problems that you may encounter while installing or using the ASUS Mobile Wireless Router. These problems require simple troubleshooting that you can perform by yourself. Contact the ASUS Technical Support if you encounter problems not mentioned in this section.Problem ActionThe ASUS Mobile Wireless Router does not power up.• Use a test meter to measure the voltage output of the power source through the power plug.• Check if the power plug is properly connected to the device.Other devices cannot communicate with the ASUS Mobile Wireless Router through a wired network connection.• Verify your network conguration to ensure that there is no IP address duplication. Turn off the device in question, then ping the assigned IP address of the device. Make sure no other device responds to that address.• Check if the cables have the proper pin outs and connectors. You may also use another LAN cable.• Make sure the hub, switch, or computer connected to the ASUS Mobile Wireless Router supports 10Mbps or 100Mbps speed.Do this by check the ASUS Mobile Wireless Router and the Hub LEDs. When you connect the ASUS Mobile Wireless Router to a 10/100 Mbps hub, both the Hub LED and the ASUS Mobile Wireless Router Ethernet LEDs should light up.My ASUS WLAN card can not associate with the ASUS Mobile Wireless Router.• Make sure your WLAN card has the same specications as theASUS Mobile Wireless Router (IEEE 802.11b/g).Minimize the distance between the devices. The ASUS WLAN card may be out of range of the ASUS Mobile Wireless Router.• Check if the ASUS Mobile Wireless Router and the ASUS WLAN card have the same SSID.• When encryption is enabled, check if the ASUS Mobile Wireless Router and the ASUS WLAN card have the same encryption settings.• Check if the Wireless LED of the ASUS Mobile Wireless Router is on.• When the Access Control table is enabled, check if the MAC address of the ASUS WLAN card is included in the Access Control table.• Check if the ASUS Mobile Wireless Router is in “Access Point” mode.
A-3ASUS WL-330N3G Mobile Wireless RouterProblem ActionThe throughput seems slow. Avoid placing the device behind a metal object. Clear obstacles between the AP and the device. Try moving the client closer to the ASUS Mobile Wireless Router and check if the throughput increases. Consider adding a second ASUS Mobile Wireless Router to implement roaming.I can not access the ASUS Mobile Wireless Router web conguration page.To access the ASUS Mobile Wireless Router web conguration page, your computer must have the same subnet as that of the ASUSPocket Wireless AP.Adjust your network if your computer’s subnet does not matchthat of the ASUS Mobile Wireless Router.The default IP address of the ASUS Mobile Wireless Router is “192.168.1.220”. In special cases, when the ASUS Mobile Wireless Router in Ethernet adapter mode joins an AP network with the same IP address, reset the ASUS Mobile Wireless Router to access the Web Conguration utility again.Where can I get a rmware le to upgrade the ASUS Mobile Wireless Router?You may download the latest rmware le from the ASUS website (www.asus.com).Use the Firmware Upgrade page in the Web Conguration utility to update the ASUS Mobile Wireless Router rmware.The ASUS Mobile Wireless Router Power LED continuously blinks for more than a minute.Turn off the ASUS Mobile Wireless Router. Turn the device again and observe if the Power LED stops blinking.If the blinking continues, you need to restore the ASUS Mobile Wireless Router rmware. Use the Firmware Restoration utility to restore or update the ASUS Mobile Wireless Router rmware.A wireless client wants to connect to the ASUS Mobile Wireless Router but can not get the correct IP from the DHCP server. (The ASUS Mobile Wireless Router has an enabled DHCP.)Make sure the DHCP server is working properly. Some DHCP servers can only assign one IP address at a time. In this case, assign a xed IP address to your ASUS Mobile Wireless Router.
A-4 Appendix: TroubleshootingManufacturer: ASUSTeK Computer Inc.Tel: +886-2-2894-3447Address: No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWANAuthorised representative in Europe:ASUS Computer GmbHAddress: HARKORT STR. 21-23, 40880 RATINGEN, GERMANYAuthorised distributors in Turkey:BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.Tel: +90 212 3311000Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10 AYAZAGA/ISTANBULINDEX BILGISAYAR SISTEMLERI MUHENDISLIK SAN. VE TIC. A.S.Tel: +90 212 3312121Address: AYAZAGA MAH. CENDERE YOLU NO.9 AYAZAGA/ISTANBULEEE Yönetmeliğine Uygundur.

Navigation menu