ATBS Technology SC-T7004 Tire Pressure Monitoring System User Manual Exhibit E User Manual rev

ATBS Technology Co. Tire Pressure Monitoring System Exhibit E User Manual rev

User manual

SC-T7004 Series TPMSFast Installation GuideBluewave Technology Co., LTD.Tel: 886-2-23451989 Fax: 886-2-234501772F.-1, No.5, Lane 178, Jhuangjing Rd.,Sinyi District, Taipei City 110, Taiwan, R.O.C.http://www.7brains.com/Email: support@7brains.com2007/4/18
ѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧʳ SC-T8000 Fast Installation GuideInstallation1. Check ComponentsReceiver(Passenger)ʳ Receiver(Truck)ʳʳ T-Type SensorReceiver SensorSC-T8000 1 4SC-T8060 1 6SC-T8080 1 8SC-T8100 1 10SC-T8120 1 12One Power CordOne Sucker & Fixture* attention: Four-wheeled passenger and truck’ s receivers are different. Please check the left-circle of receiver.2. Check Sensor Identification Number (Sensor ID) and Set2.1 Each sensor should be assigned a unique identificationnumber (ID) which was marked on the top of sensor.2.2 The last two number of sensor ID has given the locating tire position, the order is as following:* SC-T7004 ID locating position01:left-front tire 02:rght-front tire04:left-rear tire 03: right-rear tireSC-T8060 ID locating position01:left-front tire 02:rightΩfront tire05:left-rear tire right 03:righr -rear tire right06:left-rrear tire left 04:righr-rear tire left3. Install the Sensor into Wheel3.1 Screw down the original valve cap.3.2 Follow the ID’ s last two number to install the right tire (please refer to the 2.2 illustration)Note: Since sensors being electric isolation processed before shipping, it is recommended, for the first installation, to rotate sensor forward and backward several times to remove isolation coating and ensure the conductivity between sensor and valve stem. 3.3 Screw fixture: Prevent sensor from easy removing also in favor of sensor Welcome to Bluewave Super Cat T-Type 8000 Series Tire Pressure Monitoring System (SC-T7004TPMS).This Fast installation Guide is intended to give you a fast overview of the key steps required toinstall your SC-T7004 Series TPMS. For more detailed information, please refer to the SC-T7004 SeriesTPMS User’s Manual.(http://www.7brains.com)
ѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧʳ SC-T8000 Fast Installation Guidestationary.Note:(1) User may ignore this fixture, when causing inflation hassle concerns.(2) To ensure LED template display correctly coincide with actual sensor position, Please follow step 4-Sensor alignment in order to get right pressure and temperature from right sensor.4. Sensor alignmentPlug the attached power cord into cigarettelighter directly, then activate the receiver.4.1 Operation mode illustrationSC-T7004 series provides various operating mode to set differentparameter, under normal condition,please follow the above illustrationϘKey4ΰExitαfor 0.5 second into different operating modes in order to make use of different functions and parameter sets.4.2 Preset IDUnder normal conditionΔpress Δcheck the first installed tire ID is righr or not, and then press Enter , check tire ID 2, 3, and 4.If the sensors ID are all correctly located, then you can ignore the next steps.(Section 4.3).4.3 ID search and setunder normal conditionΔdo as the followings:ÆPressʳʳ(for 0.5 second) Æ Press twice Æ Press into ID searchMake sure the sensor is consistent with the main engine geared position then press Key1 (Enter),
ѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧѧʳ SC-T8000 Fast Installation Guidefollow step 3 to install the next sensor installation, after finishing press Key4 (Exit).*attention: Finished installing, LED shows “red “, If you set different sensor ID in the same place, the LED will disappear, at this moment you must reset the sensor.Signal1. Normal:When tires operate in normal condition, LED shows “green” light. Every 8 sec., the “orange” light takes turn to show each tire’ s condition.2. Abnormal:When tire is in over-heated, over-pressured, or under-pressured condition, LED shows “red”light, locks on the position of over-heated tire with “beep” sound.NOTEΚTwo tires are abnormal at the same time, it will be fixed on the abnormal status.3. Receiver did not receive Data:If receiver can not receive updated tire messages over 10 mins., LED shows abnormal indication.Example:Left-front tire didn’t receive data, shows “ t l ----”.Right-front tire didn’t receive data, shows “ t2 ----”.Left-rear tire didn’t receive data, shows “ t3 ----”.Right-rear tire didn’t receive data, shows “ t4 ----”.*attention: The abnormal signal will be disappear after once messages received. If long time no new information, please check your sensor.FCC NoticeThe changes or modifications not expressly approved by the party responsible for compliance could void the userϗs authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user sauthority to operate the equipment.
910805 2FCC Notice:Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’ s authority to operate the device.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu