User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 223505 |
| Application ID | Fch24ySRHnPWzBOQw9urdQ== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 87.05kB (1088114 bits) |
| Date Submitted | 2002-01-30 00:00:00 |
| Date Available | 2002-01-30 00:00:00 |
| Creation Date | 2002-01-24 09:19:09 |
| Producing Software | Acrobat PDFWriter 4.0 for Power Macintosh |
| Document Lastmod | 2002-01-24 14:03:39 |
| Document Title | User manual |
| Document Creator | æ¯QuarkXPress3.3k |
| Document Author: | æ¯11 |
N E OVIEW AL181 USER MANUAL 18.1 TFT LCD MONITOR ANALOG / DIGITAL [ FOR EXPORT ] LCD PC No.1 Company #1451-78, Seocho-Dong, Seocho-Gu,Seoul, 137-867, Korea TEL : 82-2-2190-5000 FAX : 82-2-2190-5009 http:// www.atech.co.kr Rev 2.0 Foundation User Manual VGA Signal Cable ▼ ▼ DC Power Supply Unit ▼ Monitor Driver Audio Cable Power Cord ▼ ▼ ▼ Option D V I(Digital Video Interface) ▼ DVI to VGA ADAPTOR ▼ DVI TV REMOTE CONTROL (Batteries Included) Audio Cable(RCA Type) ▼ Cable VIDEO RCA ▼ VIDEO USB 4PORT ▼ Cable USB ▼ USB If you select DVI for your choice, we do not provide VGA Signal Cable but only DVI Cable. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide resonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If turning the equipment off and on, the user id encouraged to try to correct the interference by one more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment an receiver. - Connect the equipment into an outlet in a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio / TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. CE Conformity Notice The Product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the "CE" mark accordingly. Confirms to the following harmonized European standards have been applied: EMC : EN 55022 Class B: 1998 EN 55024: 1998 (EN 61000-4-2: 1995, A1: 1998, EN 61000-4-3:1996, EN 61000-4-4: 1995, EN 61000-4-5: 1995, EN 61000-4-6: 1996, EN 61000-4-8: 1993 and EN 61000-4-11: 1994) EN 61000-3-2: 1995, A1: 98, A2: 98 EN 61000-3-3: 1995 Before Use Features Installing Monitor Driver Instructions for Safety How do I use the Monitor ? How do I Connect the Computer Cables ? 10 How do I Connect with the IBM computer ? Parts and Functions of ANALOG and MONITOR 12 Front view Back view The name and function of each individual part ANALOG OSD (On Screen Display) Display Selection and Control 14 DISPLAY ADJUST MISC ADJUST OSD ADJUST EXIT Parts and Functions of DIGITAL and MONITOR 17 DIGITAL OSD (On Screen Display) Display Selection and Control 18 OSD Display In case the connection is made by VGA Signal In case the connection is made by S-VIDEO In case the connection is made by COMPOSITE and S-VIDEO In case the connection is made by TV (Tuner) Information for Your Convenience Troubleshooting 25 Product Specification 28 Please keep the user manual in a place where product users can refer to it. Features 18.1 TFT LCD Panel Adopted •Adopted the 18.1 LCD (Liquid Crystal Display) Panel which allows you efficient use in a small space due to the slim design. DVI •As for most of LCD Monitors released, we support only ANALOG input, but DVI in accordance with the user's option as the video card for it has been widely used. You can get clearer pictures in DIGITAL input than in ANALOG input. AUDIO • It gives user an amplified stereo sound through internally installed speakers(2W). DESIGN •It is outstanding that Atec system has strategically planned and laid out a beautiful design that meets the taste of the new generation, super-slim model. •Swivelling at 120°to the right and the left, Tilting at 30°to the up and down. Handle for Conveyance •We do have made a handle for the easy transport carriage of monitor. Power Consumption Economy Function •The VESA DPMS (Display Power Management Signaling) function is available to reduce power consumption by automatically switching the computer into the power saving mode if the system doesn’t operate for a fixed period of time. OPTION •USB 4Port can be embedded to use the USB without an external Hub. •RCA and S-VHS terminal is supplied, connecting this apparatus to DVD, VCR or CAMCORDER. •You may view TV programs after connecting with an antenna or a cable TV. Installing Monitor Driver Manual installation method in Display Properties of Win 98 or Win 98SE 1. Insert a Diskette to A: Drive. 2. As clicking on My Computer in windows screen, follow the directions below. ① Click on ‘Control Panel’ ② Click on ‘Display’ ③ Click on ‘Settings’ ④ Click on ‘Advanced’ ⑤ Click on ‘Monitor’, then‘Change’ ⑥ Click on ‘Next’ ⑦ Click‘Display a list of all the drivers in a specific location, so you can select the driver you want ’ ⑧ Click on ‘Have Disk’ ▶ Reference If it doesn't show up the relevant model in device selection screen, click on "List all Device", then select one of them. Click on "OK" ⑨ Click on ‘OK’ ⑩ Select‘ATEC NEOVIEW AL181’, then click on ‘Next’ ⑪ Click on ‘Next’ ⑫ Click on ‘Finish’ 3. If the model name of monitor has been changed, click on‘Close’to restart Windows. Installing Monitor Driver Windows 2000 Monitor Driver Installation The followings are the way to install monitor driver in Windows 2000 Manual Installation in Display Properties. ❶ Press "Start", click "Settings" and "Control Panel". ❷ Click "Display" in "Control Panel". ❸ Click "Settings", then "Advanced". ❹ Select "Monitor", then "Properties". ❺ Choose "Driver", then "Update Driver...". ❻ Click "Next". ❼ Click "Display a list of all the drivers in a specific location, so you can select the driver you want". Then Click on "Next". ❽ Click on "Have Disk". ❾ Pointing to where the diskette or drive is located, then click on "OK". EX1] Insert a diskette to A drive bay, then press "Enter". EX2] Pointing to where the driver is located: hard disk or network. Then press "Enter". EX3] If you can't correctly designate the driver route, then click "Search" to find out the right one. ❿ Select the customer's model in "Model Selection" screen. Then press " Next". Click on "Next". Press "Yes". If "Driver installation has been successfully completed" is popped up, press "Finish". Click "Close", then press "OK" to close the display screen. Installing Monitor Driver Configuring Monitor in Linux It is the direction for installing monitor in Linux. ❶ You'd make xf86config file to run X-WINDOW. Your monitor is surely and easily configured with this file. This file will be made as running xf86config. ❷ Press Enter in the first and second screen after running xf86config file. ❸ In third screen, we come up with the mouse setting screen. ❹ Configure it as opt for user system. ❺ Next will be the screen for selecting KeyBoard. ❻ Configure it as opt for user system. ❼ First, configure a horizontal frequency. Please refer to the horizontal frequency in monitor manual. (User may directly input frequency.) ❽ Next, configure a vertical frequency. Please refer to the vertical frequency in monitor manual. (User may directly input frequency.) ❾ Then, configure a monitor. ❿ Type in the model name of monitor. The monitor's identification and description (typed in here) aren't directly related with the execution of X-WINDOW. After complete with other hardware settings, run X-WINDOW. As the configuration has been successfully finished, save a configuration file. Now run X-WINDOW. Theoretically, it is supposed to be executed. But in some cases, it won't even start. In this case, edit a xf86config file. Instructions for Safety ▶Matters that demand special attention are divided into ‘Warning’and‘Caution’, and are detailed a follows Warning In case of the possibility that a serious injury or death may occur during a violation of the instructions. Warning No one but trained repair engineers may disassemble the monitor. Please contact the appropriate sales agency or customer counsel window for check-ups, adjustment and repair. A fire or electric shock accident may be caused. as following. ※A sign signifies the need for particular attention in order to avert certain conditions. In case of the possibility that a slight injury or product damage may occur during a violation of the instructions. Don’t place or drop metals (such as coins, hair pins, or ironware) or flammable items (such as paper, or matches) onto the monitor. and userguide instructs potential danger under Caution A fire or electric shock accident may be caused. ※The sign on the product Please note not to allow liquids such as chemicals, water etc to contact the monitor. A fire or electric shock accident may be caused. Don’t place the monitor near to heat sources (such as a fireplace), and keep out of the sun. A fire or electric shock accident may be caused. Warning Please be careful to keep the panel from being scratched or damaged when you transport the monitor. plug completely so that the power supply unit can be connected tightly. The panel may be damaged, causing a failure. Unsafe power connections may cause a fire. Don’t set up the equipment in a humid environment (such as bathroom, rainy or windy area, etc). Please stop using in case of smoke or abnormal odors. Immediately switch off the power, and pull out the power cord from the wall. Contact the service center. Accidents of electric shock, fire or failure may occur. Please insert the two pins of the Continuity of use in such a state may cause a fire or electric shock. Don’t sprinkle water directly on any part of the monitor body. Please keep the power cord from proximity to a heating instrument. An electric shock or fire accident may occur. The covering material of the cord may melt, causing a fire or electric shock. Warning Never touch the power plug with wet hands. An electric shock accident may occur. Please set up the monitor at a proper distance (over 10 cm) away from the wall for sufficient ventilation. A fire may be caused due to an increase in internal temperature. Please note that air-flow holes must not be blocked by a table cloth or curtain. A fire may becaused due to an increase in internal temperature. Don’t use a power cord or plug that is damaged or has a loose connection. An electric shock or ignition may be caused. Please grasp the power plug at the base to remove it from the wall, and pull firmly but gently. If you yank at the cord the wire may be broken, causing ignition or heat generation. Don’t set up the equipment on an unsupported shelf or angled surface. nor on an area subject to serious vibration. Fall or displacement of the equipment may cause an injury. Warning You must switch the power off and pull the power cord out before moving the monitor. You should also check as to whether external connection cords - such as the connection cords between component parts - are all pulled out before the movement. A damaged cord may cause a fire or electric shock. Don’t set the monitor in a narrow place with poor ventilation such as a bookcase A fire may be caused due to an increase in internal temperature. Pull the power cord out when the monitor is not used for a long time, or while you are away. A dust covering may cause an electric shock, electric leakage, or fire by heat generation, ignition, and insulation degradation. When you clean the panel surface, pull the power cord out first, and wipe the surface with a clean, dry and soft cloth. Don’t use a damp cloth. Such action may be the main cause of an electric shock accident and failure. Caution Don’t put pressure upon the panel or score the surface with your hands or sharp items (nails, pencils, pens, etc). Damage or failure of the panel may be caused. When you move the monitor, take hold of it with both hands setting the panel forward. If you drop the monitor, contact the service center to check it for a susceptibility to fire or electric shock. How do I connect the computer cables? How do I connect with the IBM computer ? ▶ Reference ◈ In case of the monitor aiding ANALOG (VGA) No Input signal message 1. Ensure that the computer, monitor and peripheral equipment power is turned off. It is a message appeared in case signal input cable is 2. Connect signal cable to D-Sub signal input connector, and VGA signal cable to signal input connector of monitor. Connect one DC power jack of DC power supply unit to the 12V 3. terminal, and the other to the power cord. Next connect the power inexactly connected between monitor and computer. Please refer to the message “Please confirm before you report the trouble” for details. cord to the concent. 4. Turn the monitor power on after switching the computer power on. If the message “NO INPUT SIGNAL”shows up, check the connection 5. of VGA signal cable or connector. 6. Switch the monitor and computer power off at the end of use. Connect with the Macintosh computer Use the appropriate MAC to VGA adapter block at your system. VGA Signal Cable Audio Cable ▶AUDIO Cable is connected to LINE OUT Power Cord DC Power Supply Unit How do I connect the computer cables? How do I connect with the IBM computer ? ◈ In case of the monitor aiding DIGITAL (DVI) that the computer, monitor and peripheral equipment power is 1. Ensure turned off. Signal Cable. 2. Connect ① In case of using DIGITAL Cable. - Connect one DVI Signal Cable each to the mainframe and monitor. ② In case of using ANALOG Cable (Refer to the left side illustration). - Connect DVI to VGA adaptor positioned at the rear side of the monitor. Then connect it to the mainframe. ▶ Reference In case of using ANALOG in DVI model monitor, you must set up the adaptor as shown on the illustration. 3. Connect one DC power jack of DC power supply unit to the 12V terminal, and the other to the power cord. Next connect the power cord to the concent. 4. Turn the monitor power on after switching the computer power on. If "NO INPUT SIGNAL" appears, check the DVI Cable (or VGA Signal 5. Cable connection). 6. Switch the monitor and computer power off at the end of use. DVI Signal Cable Audio Cable ▶AUDIO Cable is connected to LINE OUT Power Cord DC Power Supply Unit Parts and Functions of ANALOG and MONITOR Front View Power Pilot Lamp POWER Button MENU Button SELECT Button DOWN Button Back View AUTO Button UP Button 1. DC 12V INPUT (connected to adaptor) 2. VGA(Analog) or DVI(Digital) INPUT [DVI is OPTION] 3. S-VHS INPUT (video image input 2) 4. RCA INPUT (video image input 1) 5. AUDIO IN (connected to LINE OUT of PC's mainframe) 6. AUDIO OUT (linked to external speaker or headset) 7. USB UP (connected to PC's mainframe) 8. USB 4DOWN(connected to USB KeyBoard, Mouse, and Camera) 9. TV ANTENNA (connected to antenna cable for televiewers) * 2 DVI , 3 , 4, 7, 8, 9 are OPTION. ❷ Parts and Functions of ANALOG and MONITOR The Name and Function of Each Individual Part in the Screen Adjusting Block Power Pilot Lamp Lights up during the operation but goes out if you turn the power off. Front Monitor ❶ ❷ ❸ ❹ ❺ ❻ ❶ MENU Button It makes OSD menu picture appear or disappear. It is also used when you enter into or get out of submenu. ❷ SELECT Button Used to select an icon to be adjusted from the OSD screen. ❸ DOWN Button ❹ UP Button It is for shifting OSD screen to up and down or increase and decrease the value of icon selected. (And it also volume up and down without pressing MENU.) ❺ AUTO Button The screen is automatically adjusted to the optimal display state applicable to the current mode, while the following message appears. ❻ POWER Button Once pressed, it powers up the system. Once more, it shuts down the system. - Green ON : system activated - Amber Blinking : 1. System Standby 2. Monitor Power Saving Mode 3. VGA signal cable Unhooked ANALOG OSD (On Screen Display) Display Selection and Control Use the OSD adjustable buttons on the side of the monitor to set/adjust to the best screen and operating environment. If you have to adjust the screen, please adhere to the following procedure. ❶ Press MENU Button to show you OSD menu screen. ❷ Press DOWN Button to select the preferred main menu, then press MENU Button once more to get in subordinate menu screen. ❸ As pressing UP / DOWN Button, you can go to the menu that you prefer. Press SELECT Button. ❹ Set the preferred value as using UP / DOWN Button. ❺ Press MENU Button once more, then it reverts to the main menu screen. ❻ As using DOWN Button, go back to EXIT OSD. AUTO Function If you select the AUTO button before using the OSD menu, the screen is automatically adjusted to the optimal display state applicable to the current mode, while the following message appears. If you don’t like the auto adjustment, you have to manually adjust the H/V Position, Clock, and Phase of the OSD menus. AUTO is most appropriate when it is operated on background display color closest to white. (For more information, p lease refer to pages 15 - 21) ANALOG OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions DISPLAY ADJUST •BRIGHTNESS - It is used to adjust brightness of the screen. •CONTRAST - It is used to adjust distinction. •PHASE - It is used to adjust the phase of the screen. Please use it in case there is noises or lines are overlapped. •CLOCK - Controlling the horizontal size in screen. •H- POSITION - It is used to move screen right-wards or left-wards. •V- POSITION - It is used to move screen up-wards or down-wards. •FACTORY DEFAULT (Manufactured Initial Value) - It goes back to the initial value that has been set as forwarding. •AUTO (Auto Set) - It is configured as the most appropriate, optimized screen. MISC ADJUST •DOS MODE - It is to optimize TEXT and GRAPHIC. •R GAIN - Modify the value of red. •G GAIN - Modify the value of green. •B GAIN - Modify the value of blue. •COLOR TEMPERATURE - configured to one of 9500, 8000, 6500(Default), and 5000. - 9500 : selected to blue color hued screen. - 5000 : selected to red color hued screen. •WHITE BALANCE - It automatically sets Color Balance. (It will be adjusted to optimization after making background screen a white color.) ANALOG OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions OSD ADJUST •H-POS (OSD horizontal position) - Horizontal position in OSD menu is adjusted as controlling the numerical value of it. •V-POS (OSD vertical position) - Vertical position in OSD menu is adjusted as controlling the numerical value of it. •OFF TIME (Setting OSD disappearance time)- OSD menu configures a disappearance time. The maximum time of 100 sec may be set, so that it will automatically vanish unless any input value is noticed within 100 sec. (Default:15 Sec) •TRANSPARENCY (OSD Transparency) - It configures the basic color of OSD menu from opacity to transparency. •LANGUAGE - One of English, Japanese, Korean, German, French and Spanish may be selected. EXIT •EXIT OSD - It goes out of OSD menu. ▶ Reference Ver 1.0 1280X1024 / 60Hz DIGITAL OSD (On Screen Display) Display Selection and Control The Name and Function of Each Individual Part in the Screen Adjusting Block Power Pilot Lamp Lights up during the operation but goes out if you turn the power off. Front Monitor ❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽ ❶ MENU Button It makes OSD menu picture appear or disappear. It is also used when you enter into or get out of submenu. ❷ SELECT Button Use SELECT button if you wish to change OSD value. SOURCE will change when you press SELECT button. (If you press once, the present SOURCE will appear. Press once more, the SOURCE will convert.) ❸ DOWN Button ❹ UP Button Use these buttons when moving up and down in OSD (It is TV channel increase (UP) and decrease (DOWN) function when this button is pressed without pressing MENU button.) ❺ LEFT Button ❻ RIGHT Button It is used to increase and decrease the SELECTION ICON value in OSD display. (It is the VOLUME increase and decrease function when this button is pressed without pressing MENU button.) ❼ AUTO Button When you press this button, it is automatically adjusted to the most appropriate condition to present mode. This does not function when DIGITAL VIDEO CARD (DVI Card) is used. (It is adjusted automatically.) ❽ POWER Button Once pressed, it powers up the system. Once more, it shuts down the system. - Green ON : system activated - Amber ON : 1. System Standby 2. Monitor Power Saving Mode 3. VGA signal cable Unhooked DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions OSD Display ▶ Function Description ▶ Mode Information ❶ When you press the MENU button without OSD display, the display shown above will appear. ❷ You can indicate and enter in by UP/DOWN buttons . ❸ At this point, you can enter in when you press the menu you have selected and can be controlled by UP/DOWN buttons. At this point, converted contents can be checked by graphs and numbers Indicated numbers, in domain value, can be controlled and they are not the absolute value. ▶ Reference ◈ No need to press AUTO CONFIGURATION button when Digital Video Card is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when PROCESSING Message SXGA 1280X1024 is used ▶ A message indicating PROCESSING Status! ▶ A message during AUTO CONFIGURATION operation. •'PROCESSING AUTO CONFIGURATION' is a message demanding your patience while monitor is searching for the most appropriate background display. ▶ A message while Power Saver Mode •'POWER SAVER MODE' is a message indicating is on the process (converts into Power Saver Mode after 5 seconds). the monitor is on the process of entering the Power Saver Mode. ▶ A message indicating failure of entered signal •'OUT OF FREQUENCE' is a message indicating an input signal is out of boundary, which monitor can handle. This is case which video card output has problems of either not aiding "plug-and-play" or not clearly recognizing the monitor's information, so please check with the Aid Resolution (Page 26). in Digital Monitors (does not aid to 75Hz). DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions In case the connection is made by VGA Signal ▶ Control the Screen Brightness ▶ Control the Screen's Shade of Color ▶ PRESET1 : Light Blue Display PRESET2 : General Display ▶ Reference ◈ No need to press AUTO ▶ RED, GREEN, BLUE: Color Chosen by User CONFIGURATION button when Digital Video Card is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when SXGA 1280X1024 is used in Digital Monitors (does not aid to 75Hz). ▶ HORIZONTAL : Display Horizontal Movement VERTICAL : Display Vertical Movement CLOCK : Control of the Display Quality by Increasing Display's Size PHASE : Detailed Control of the Display Quality. DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions In case the connection is made by VGA Signal ▶ Reference ◈ No need to press AUTO CONFIGURATION button ▶ OSD POSITION : Rotates in this order: top left side, top right side, middle, bottom right side, bottom left side. OSD TIME : Waiting period for OSD indication when no control is made during OSD screen display. SOURCE : Converts any input signal into ANALOG,DIGITAL,COMPOSITE, S-VIDEO and TUNER. when Digital Video Card is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when SXGA 1280X1024 is used In case the connection is made by COMPOSITE and S-VIDEO in Digital Monitors (does not aid to 75Hz). ▶ Control Darkness Level of Signal ▶ Control the Screen's Shade of Color DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions In case the connection is made by COMPOSITE and S-VIDEO ▶ SHARPNESS : Control Screen Distinction COLOR : Control Screen's Depth of Color T I N T : Control Screen's Tint of Color ▶ Reference ◈ No need to press AUTO CONFIGURATION button when Digital Video Card is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when SXGA 1280X1024 is used in Digital Monitors (does not aid to 75Hz). ▶OSD POSITION : Rotates in this order : top left side, top right side, middle, bottom right side, bottom left side. OSD TIME : Waiting period for OSD indication when no control is made during OSD screen display. SOURCE : Converts any input signal into ANALOG, DIGITAL, COMPOSITE, S-VIDEO and TUNER. DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions In Case when a Connection is made with TV (Tuner) Signal ▶ Reference ◈ No need to press AUTO CONFIGURATION button when Digital Video Card is used (it is controlled automatically). ▶ Control the Screen Brightness ◈ Vertical Frequency can be aided up to 60Hz when ▶ Control the Screen's Shade of Color SXGA 1280X1024 is used in Digital Monitors (does not aid to 75Hz). ▶ PRESET1 : Light Blue Display PRESET2 : General Display ▶ RED, GREEN, BLUE :Color Chosen by User DIGITAL OSD (On Screen Display) Display Selection and Control Descriptions of OSD Adjustment and Functions In Case when a Connection is made with TV (Tuner) Signal ▶ Reference ◈ No need to press AUTO CONFIGURATION button when Digital Video Card ▶ AIR / CATV : Air Wave, Cable TV Selection ▶ AUTO CHANNEL : Automatically Selects Clear Channels ▶ MANUAL CHANNEL : Selects to Insert or Delete on Each Channel ▶ FINE : Any Noise Occurred on Display is Handled by a Microscopic Control ◈ When you have to move MONITOR, use AUTO CHANNEL to select clear channels. is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when SXGA 1280X1024 is used in Digital Monitors (does not aid to 75Hz). ▶OSD POSITION : Rotates in this order : top left side, top right side, middle, bottom right side, bottom left side. OSD TIME : Waiting period for OSD indication when no control is made during OSD screen display. SOURCE : Converts any input signal into ANALOG, DIGITAL, COMPOSITE, S-VIDEO and TUNER. DIGITAL OSD (On Screen Display) Display Selection and Control INFORMATION (Comparison between ANALOG and ADAPTOR) Pin Arrangement Description - Input Signal : ANALOG Formula - Connector : 15 Pin VGA Signal Cable - 15 Pin D-Sub Connector - The Purchased Monitor's Signal Cable is positioned on the rear side of Stand Pin Number 10 11 12 13 14 15 Signal Description Red Green Blue GND Self-Check Red GND Green GND Blue GND Exit GND GND Data Line (SDA) Horizontal Synchronizer Vertical Synchronizer Data Click (SCL) • 15 Pin D-Sub Connector Pin Description D-Sub DVI-D - Input Signal : Digital Formula - Connector : DVI-D model Cable - DVI-D Connector ▶ Reference Pin Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Shell Signal Description TMDS DATA2TMDS DATA2+ TMDS DATA2+/Shield NC NC DDC SCL DDC SDA NC TMDS DATA1TMDS DATA1+ TMDS DATA1/Shield NC NC +5V Power GND(for+5V) Hot Plug Detection TMDS DATA0TMDS DATA0+ TMDS DATA0/Shield NC NC TMDS Clock/Shield TMDS Clock TMDS Clock GND • DVI-D Connector Pin Description ◈ No need to press AUTO CONFIGURATION button when Digital Video Card is used (it is controlled automatically). ◈ Vertical Frequency can be aided up to 60Hz when SXGA 1280X1024 is used in Digital Monitors (does not aid to 75Hz). Tr o u b l e s h o o t i n g Please check the below particulars before you contact the service center to notify an abnormality of the monitor. Check these points This symptom can be discovered Take these respective actions Is the monitor power cord inserted ? Please connect the power cord correctly to the concent. Is the power turned off ? Please press the power button. Is the power turned on and the power pilot lamp Blinking Amber? The monitor is in the power saving mode. Please therefore move the mouse, press any key on the keyboard, or recheck VGA Cable connection. Is the message“Out Of Range”shown ? If a power indicating lamp of amber color blinks, press any key to go back to previous mode. As it passes over the frequency limit of horizon (31.5-80 kHz) and verticality (60-75 Hz) in PC (video card), you'd reconfigure it as referring to the specification of this manual. (If you install the monitor driver that we have provided, it won't come up with the message“OUT OF RANGE”.) Is the message“No Input Signal”shown? It shows up as PC changes to power-saving mode or the signal cable between PC and monitor isn't rightly connected. Move your mouse or press keyboard button. But it won't still show you a right screen, then recheck a signal cable connection. The screen doesn’ show anything. Tr o u b l e s h o o t i n g Please check the below particulars before you contact the service center to notify an abnormality of the monitor. Check these points Take these actions This symptom can be discovered Has a discoloration (into 16 colors) of the screen occurred? Do you see a spot on the screen? Set the number of colors to more than 256 colors. On the Windows 95/98, perform the following process [Control Panel] -> [Display] -> [Setting] -> [Color Table] -> [256 Colors] -> [OK] You may see a few spots (in red, green, white and black) on the screen during the operation. Occurrence of such a phenomenon is not a failure but a characteristic of the LCD panel, and therefore has no relation to the performance of the monitor. The color of the screen is not normal Troubleshooting Please check the below particulars before you contact the service center to notify an abnormality of the monitor. Check these points Take these actions Is the positional adjustment made correctly? Push the 'AUTO' Button, then the screen will beadjusted automatically in to the optimal state applicable to the current mode. If you are not satisfied with the auto adjustment, you can directly adjust the H Position (Horizontal Position), V Position (Vertical Position), and Clock (Horizontal Size) of the OSD menus. Is the phase adjustment made properly? Push the 'AUTO' Button, then the screen will beadjusted automatically in to the optimal state applicable to the current mode. If you are not satisfied with the auto adjustment, you maymanually adjust the Phase (Focus) of the OSD menus. Is the screen set in the best state? While you are using this product in the mode of 1280X1024 and 60Hz, the best condition of the screen is available. In the mode of VGA(640x480),SVGA (800x600) or XGA (1024x768), the outline of a letter may be seen dimly or unevenly. This symptom can be discovered The screen is under a bias toward one side, or is not centrally positioned. A faint letter is shown, or the phase is out of focus. Noise is also generated horizontally. Product Specification The details of product specification can be changed without notice to improve the product. panel type screen size pixel size contrast color brightness a-Si active matrix TFT-LCD 18.1 (459.14mm) diagonal 0.2805mm x 0.2805mm 250:1(Typical) 8-bit(16,777,216 Colors) 200cd/m2 Picture Signal resolution horizontal frequency vertical frequency view angle input picture signal SXGA 1280 x 1024@ 60Hz 31.5 - 80kHz 60 - 75Hz U/D:±70°, R/L: ±70° Analog RGB,OPTION(DVI, RCA, S-VHS) AUDIO output Stereo 2Watt x 2 Input Connector input terminal user’s control 15Pin D-Sub(Analog RGB), OPTION(DVI) Auto Configuration, Brightness, Contrast, H-Position, V-Position, Color RGB, Phase, Frequency, Volume, Language,etc. Dimension and Weight body size(WxDxH) weight 448x 241.3x 441mm 7.5kg(Unit), 10kg(Packed) power managing system power consumption input power VESA DPMS standard ≤48 Watt AC 110~220V, DC12V LCD Panel Power Product Specification Factory-specified Mode Factory-specified Mode 10 11 12 13 VGA VGA VGA VGA VGA SVGA SVGA SVGA XGA XGA XGA SXGA SXGA 640 ×350 640 ×480 640 ×480 640 ×480 720 ×400 800 ×600 800 ×600 800 ×600 1024×768 1024×768 1024×768 1280 ×1024 1280 ×1024 Vertical Horizontal Frequency(kHz) Frequency(Hz) 31.47 31.47 37.86 37.50 31.47 37.88 48.68 46.88 48.36 56.48 60.02 64.0 79.98 70 60 72 75 70 60 72 75 60 70 75 60 75 ※ Remarks 1. The indication in above diagram and actual value shall not be always coincident. This product automatically adjusts for optimum condition by itself. 2. In case of any trouble in user's set-up, it automatically returns to the initial set-up mode.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Creator : .歯.QuarkXPress3.3k Create Date : 2002:01:24 09:19:09 Author : .歯.11 Producer : Acrobat PDFWriter 4.0 for Power Macintosh Modify Date : 2002:01:24 14:03:39+09:00 Page Count : 34EXIF Metadata provided by EXIF.tools