ATEK TSM7 TankSan TS Series Monitor User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	1319221
Application ID	yx128vkmhthYuQfY3bTksg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.56kB (94470 bits)
Date Submitted	2010-07-29 00:00:00
Date Available	2010-07-29 00:00:00
Creation Date	2010-07-19 08:15:41
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2010-07-19 08:15:41
Document Title	Microsoft Word - TankScan TS Series Hardware Installation and User Manual 7-15-10.doc
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	mburman

Revision 6/22/10
TankScan TS Series Hardware Installation and User Manual
TankScan TS Series Hardware Installation
Install the TS Series Controller
Determine the best Controller location
Ensure shortest possible distance between all the Monitor locations and the
Controller with no obstructions in the path (line of sight).
Location should be within a building and near a connection for the mode of
communication desired (analog dial up, USB, Ethernet, etc.).
Mount the Controller at the desired location
Attach the antenna to the back of the Controller. (Note: the antenna
connection is a left-hand thread)
Connect power using the wall plug transformer supplied. The LCD panel on the
front of the unit should be on after power is applied.
Connect the Controller to the desired mode of communication.
Install the TS Series Monitor(s)
Determine the desired length of the Monitor probe, cut it to length and attach the
supplied weight.
Mount the Monitor onto the tank by threading it onto the 1-1/2” or 2” threaded hole.
Remove the battery compartment door using the supplied screwdriver, insert the
battery into the compartment and plug it in. The Monitor will take a measurement and
send the information to the Controller within about 10 seconds.
Swiping the magnet end of the supplied screwdriver over the “Swipe Magnet
Here” label on the Monitor will put the Monitor into “Test” mode.
•
In “Test” mode the Monitor will continue to take and send
measurements approximately every 30 seconds for ten minutes.
Determine and add the “Offset”. The Offset is a function of how and where the monitor
is mounted relative to the full level of the tank
Manually measure the level in the tank.
Calculate the Offset as: Offset = Manual Reading - Monitor Reading
Add the calibration Offset to the monitoring software.
Repeat for each Monitor being installed.
Refer to the TankScan 2 User Interface Map for viewing data on the LCD panel.
Confidential – ATEK Products, LLC
Revision 6/22/10
FCC Notes
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
“This device has been designed to operate with the antenna supplied, and having a maximum gain of 3
dB. Antennas not included or having a gain greater than 3 dB are strictly prohibited for use with this
device. The required antenna impedance is 50 ohms.”
“To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.”
“To comply with FCC and Industry Canada RF radiation exposure limits for general population, the
antennas used for these transmitters must be installed to provide a separation distance of at least 20cm
from all persons and they must not be collocated or operated in conjunction with any other antennas or
transmitters.”
“Changes or modifications not expressly approved by ATEK Products, LLC could void the user’s authority
to operate the equipment.”
Confidential – ATEK Products, LLC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Producer                        : Nitro PDF PrimoPDF
Create Date                     : 2010:07:19 08:15:41+04:00
Modify Date                     : 2010:07:19 08:15:41+04:00
Title                           : Microsoft Word - TankScan TS Series Hardware Installation and User Manual 7-15-10.doc
Creator                         : PrimoPDF http://www.primopdf.com
Author                          : mburman

EXIF Metadata provided by EXIF.tools