ATID AT312 3G Smart phone User Manual 9 19

ATID Co., Ltd 3G Smart phone 9 19

User manual

Download: ATID AT312 3G Smart phone User Manual              9 19
Mirror Download [FCC.gov]ATID AT312 3G Smart phone User Manual              9 19
Document ID3071444
Application ID4idX1D25N+c7ZpfJw5lXWQ==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize67.82kB (847714 bits)
Date Submitted2016-07-21 00:00:00
Date Available2016-07-21 00:00:00
Creation Date2016-07-21 14:58:31
Producing SoftwareCorel PDF Engine Version 14.0.0.701
Document Lastmod2016-07-21 14:58:31
Document Title封面-9.19
Document CreatorCorelDRAW
Document Author: Administrator

CE Warning:
1. Use careful with the earphone maybe possible excessive sound pressure from
earphones and headphones can cause hearing loss.
2. Caution : Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
3. The product shall only be connected to a USB interface of version USB2.0
4. Adapter shall be installed near the equipment and shall be easily accessible.
5. Extreme operating tempature: -20~+40 degree centigrade
6. The plug considered as disconnect device of adapter
7. The device complies with RF specifications when the device used at 0mm form your
body
8. Hereby, Shenzhen BoRui Technology Co.,Ltd declares that this 3G Smart phone is in
compliance with essential requirements and other relevant provisions of Directive
1999/5/EC.
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Specific Absorption Rate (SAR) information:
This 3G Smart phone meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific studies.
The standards include a substantial safety margin designed to assure the safety of all
persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: 3G Smart phone (FCC ID:
VUJ-AT312) has also been tested against this SAR limit. This device was tested for
typical body-worn operations with the back of the Tablet PC kept 10mm from the
body. To maintain compliance with FCC RF exposure requirements, use accessories
that maintain a 10mm separation distance between the user's body and the back of the
3G Mobile Phone. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that do not satisfy
these requirements may not comply with FCC RF exposure requirements, and should
be avoided.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Modify Date                     : 2016:07:21 14:58:31+08:00
Create Date                     : 2016:07:21 14:58:31+08:00
Metadata Date                   : 2016:07:21 14:58:31+08:00
Creator Tool                    : CorelDRAW
Format                          : application/pdf
Title                           : 封面-9.19
Creator                         : Administrator
Document ID                     : uuid:c4c75d03-4837-459c-b198-d45f852db2f1
Instance ID                     : uuid:2b3e29ca-274f-4cfc-b96d-20111d9a9378
Producer                        : Corel PDF Engine Version 14.0.0.701
Has XFA                         : No
Page Count                      : 38
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VUJ-AT312

Navigation menu