ATTOWAVE RLS2 RADAR DETECTOR User Manual Manual RLS2 K40 20141106

Download:
Mirror Download [FCC.gov]
Document ID	2439341
Application ID	MXvWxyPSdCCglFRgefsKfA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.98kB (124692 bits)
Date Submitted	2014-11-07 00:00:00
Date Available	2014-11-07 00:00:00
Creation Date	2009-11-06 17:47:31
Producing Software	Hancom PDF 1.3.0.428
Document Lastmod	2009-11-06 18:13:05
Document Title	Microsoft Word - Manual_RLS2_K40_20141106.doc
Document Creator	Hancom PDF 1.3.0.428
Document Author:	twkim

INTRODUCTION
K40 ELECTRONICS
RADAR-LASER DETECTOR
Thank you for purchasing K40’s newest radar laser detector “RLS2”
The RLS2 model incorporates the advanced new radar antenna technology and
extremely low power-consuming circuitry to ensure top class performance. It is a
complete integrated laser and radar detector, which responds not only to X, K
and Ka band radar guns in use today, but also the laser guns.
The RLS2 provides distinct visual and audio alerts to warn you of the presence
of X, K, Ka band and laser signals for 360° round.
You can drive with confidence when you bring along the RLS2 radar laser
detector.
Operating Instructions
PACKAGE CONTENTS
RLS2 package includes the following components.
MODEL : RLS2
·
·
·
·
·
RLS2 radar and laser detector
12-volt DC power cord and fuse (2types – Coiled and Straight)
Windshield mounting bracket with suction cups
Dashboard mounting hook and loop fasteners
Operation manual
-1-
Windshield Mounting
The supplied windshield bracket and suction cups let you quickly mount the
detector on your vehicle’s windshield.
INSTALLING THE UNIT
Mounting Guidelines
For the best performance, select the proper location for the detector where it has
a direct view of the road. Remember the radar antenna and laser sensor are
located behind the rear panel of the unit.
The antenna and sensors should not be obstructed by metal or metallic surfaces
and should be pointed at the horizon for accurate long-range detection.
- Choose a location that does not block the driver's vision.
- Mount the detector in a level position.
- Do not mount the detector behind the metal surfaces and ornaments mirrored
sunscreen.
Tinted windows reduce the received laser signal strength.
Do not mount the detector behind tinted glass. Do not mount the detector where
the driver or passenger might hit in a sudden stop or accident.
Follow these steps to use mounting bracket kit.
1.
2.
3.
4.
5.
6.
Install the suction cups onto the bracket by fitting them into their holes.
Attach the bracket to windshield.
Attach the detector to the bracket.
Bend bracket for correct detection angle.
Plug power cord DC12V into detector.
Plug power cord into cigarette lighter.
Cautions: Some new models of cars have a plastic safety coating which is
applied to the windshield. The suction cups may leave permanent marks on the
wind shield once they are removed. Check vehicle owner’s manual to see if your
car has the plastic safety coating.
Connecting the Power
Mounting Type
The RLS2 detector is designed to operate on most DC 12V negative ground
vehicle electrical systems. The power cord provided with the detector has a
cigarette lighter socket plug at one end and a small connector at the other.
There are two ways of installation.
Hook and Loop Mounting
The hook and loop tape included with your detector might be the best mounting
method for some dashboards.
Follow these instructions to use the hook and loop tape to mount the unit on the
dashboard.
1. Use a damp cloth to thoroughly clean the dashboard.
2. Peel off the paper backing of the tape and apply the tape to the bottom of the
detector.
3. Remove the paper backing from the other side of the tape and press the
detector onto the dashboard.
-2-
1. Insert the small connector into the jack on the side of the detector.
2. Insert the other end into the cigarette lighter socket of your vehicle.
If the detector does not operate when you turn it on, remove the adapter from the
cigarette lighter socket and carefully check the socket for debris. Also, check the
fuse in the adapter and your vehicle's fuse box.
Replacing the Fuse
If the detector stops operating, the fuse in the cigarette lighter plug might be
blown. If it has blown, follow these steps to replace it:
1. To replace the fuse, unscrew the top of the plug.
2. Remove the fuse and check the fuse to see if it has blown. If it has, replace it.
-3-
b. Press and hold Dim/Menu button for 3sec.
c. Do nothing for 10sec.
OPERATION
1) Power On & Volume Control
Rotate the Power and Volume control wheel clockwise to turn the Power on/off.
This wheel can adjust volume up/down also by moving back and forth.
2) Dim & Menu Button
DIM MODE
Dim mode reduces the illumination of the display.
Press and release Dim/Menu button to change display brightness from Day Dusk – Night-Auto and to off.
On Auto mode, display keeps “Dusk” on standby and when alarm starts, it
changes the brightness level in order of Day-Dusk-Night until the alarm stops.
3) Quiet Ride Button
Press and release Quiet Ride button to enter Quite Ride Mode.
Quiet Ride Mode allows you to set a minimum MPH or KPH detection speed
that eliminates all audible alerts until the vehicle exceeds your selected speed.
Use up(∧) and down(∨) button to select your choice of speed in range of
5~65MPH(by 5MPH) or 10~100KPH(by 10KPH).
To save the selection and exit the menu, do nothing for 3sec.
Display shows selected speed for Quiet Ride Mode along with voice
announcement “Quiet Ride Set”.
4) MUTE Button
MENU MODE
Press and hold Dim/Menu button for 3sec. to enter Menu Mode.
On Menu Mode, press Dim/Menu button to scroll down on menu.
Press City /Hwy button to scroll up on menu.
Press Up(∧)/Down(∨) button to select from menu.
a.MUTE MODE
Press and release MUTE button to turn on/off Mute Mode.
Mute Mode silences all beeping alerts for radar/laser alarms for 15sec. or the
duration of the alert. Voice alerts stay active.
b.EXTENDED MUTE MODE
Press and hold Mute button for 3sec. to turn on/off Extended Mute Mode.
Extended Mute Mode silences all beeping alerts for radar/laser alarms for
2minutes or the duration of the alert. Voice alerts stay active.
Menu Options
FEMALE
MALE
VOICE ON
VOICE OFF
WAKEUP_LONG
WAKEUP_SHORT
SPEED ON
SPEED OFF
COMPASS ON
COMPASS OFF
POP_ON
POP OFF
MPH
KMPH
X BAND ON
X BAND OFF
K BAND ON
K BAND OFF
KA BAND ON
KA BAND OFF
LASER ON
LASER OFF
5) CITY/HWY Button
Press and release CITY/HWY button to toggle between Highway - City -Filter.
a.HIGH WAY MODE – Detects all types of FCC approved police radar or laser
signals at full sensitivity.
b.CITY MODE : The X-band sensitivity is reduced.
This is because it is the most common source of police radar signals.
K,KA and Laser remain at full sensitivity.
FACTORY RESET
EXIT
To exit the menu,
a. Press “UP” or “DOWN” button while “exit” is being displayed.
-4-
c.FILTER MODE : Eliminates X-band completely. Reduces K and KA band
sensitivity. Laser detection remains at full sensitivity.
-5-
SPECIFICATIONS
d.SPEED MONITOR MODE : Speed Monitor function alerts the driver when a
preselected speed is exceeded. The speed Monitor can be set to any speed
between 40~100MPH (in 5mph increments) or 60~160KPH (in 10kph
increments)
The RLS2 emits a beeping alert tone accompanied by the visual display blinking
“Slow Down” repeatedly.
The alerts will continue until the vehicle’s speed is reduced to below the Speed
Monitor setting. The factory default setting for Speed Monitor is “Off”
To access and turn on this function:
-Press and hold CITY/HWY button for 3sec.
-Press and release Up(∧) and Down (∧) button to select the desired maximum
speed for alerts.
5seconds after your speed is selected, your setting will be saved, the voice will
announce “Speed Monitor Set” accompanied by the visual display blinking the
selected speed twice and your display will return to the main screen.
6) MARK Button
The Mark” function allows you to receive both audio and visual alerts for
specific locations you’ve stored.
Press and release Mark button when you are at the location.
Display shows “ Alrt Loc” and voice announces “Marked to Alert”.
After marking the location, when you arrive within a radius of 1500feet of the
marked location, the voice will announce “approaching marked location”
accompanied by visual display “Alrt Loc”
When you are at a marked location, you will hear a single “Bing” tone.
To remove a previously marked location, press and release Mark button while in
that location.
To remove all currently stored locations, select “All Alertlocs Clr” from Menu.
Radar Frequencies :
10.475 - 10.575 GHz (X Band)
24.050 - 24.250 GHz (K Band)
33.400 - 36.000 GHz (Ka Superwideband)
Laser Wavelength : 905nm +/-50nm
Operating Temperature Range :
-10C to +70C (+14F to +158F)
Power Requirements:
Operational 12 to 15volts DC,250mA nominal(2amp fuse) Vehicle Battery
Saver, 30mA nominal
FCC INFORMATION (FCC ID : W75-RLS2)
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
In addition, any changes or modifications to this product, which are not
expressly approved by K40 Electronics in writing, could void the user's authority
to operate this product.
LIMITED WARRANTY
The manufacturer warrants this product against all defects in materials and
workmanship for a period of one (1) year from the date of the original purchase,
subject to the following terms and conditions: The sole responsibility of the
manufacturer under this Warranty is limited to either repair or, at the option of
the manufacturer, replacement of the unit. There are no expressed or implied
warranties, including those of fitness for a particular purpose of merchantability,
which extend beyond the face hereof.
-6-
-7-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : Yes
Language                        : ko-KR
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
PDF Version                     : 1.4
Producer                        : Hancom PDF 1.3.0.428
Creator Tool                    : Hancom PDF 1.3.0.428
Create Date                     : 2009:11:06 17:47:31+09:00
Modify Date                     : 2009:11:06 18:13:05+09:00
Metadata Date                   : 2009:11:06 18:13:05+09:00
Format                          : application/pdf
Creator                         : twkim
Title (x-repair)                : Microsoft Word - Manual_RLS2_K40_20141106.doc
Date                            : 2009:11:06 17:47:31+09:00
Document ID                     : 0954EA4C-2B13-4B41-85FB-8E3B8670FBB4
Instance ID                     : uuid:2804d41f-9ef6-4430-a762-ed8fb7b57148
Part                            : 1
Conformance                     : B
Page Layout                     : SinglePage
Page Count                      : 4
Author                          : twkim
Title                           : Microsoft Word - Manual_RLS2_K40_20141106.doc

EXIF Metadata provided by EXIF.tools