AVID ID Systems 125-AV1040 Wand Reader User Manual
AVID ID Systems, Inc. Wand Reader Users Manual
Users Manual
Warranty and Service
The Avid Mini-TracKer Wand Reader is warranted against defects in material and
workmanship, under normal use and service, for a period of 1 year from the date of
shipment from AVID. This warranty will not apply if repairs, parts or adjustments are
required due to accident, neglect, damage during transportation, or causes other than
ordinary use. AVID’s sole responsibility under this warranty shall be, at AVID’s option,
to either repair or replace any product, which fails during the warranty period. In no
event shall AVID be liable for any indirect or consequential damages or loss of profits.
A Return Material Authorization (RMA) number must be issued before a unit is
returned to AVID for service. Contact AVID for a RMA number or other service
questions. (951) 371-7505.
Copyright 2004 © Avid Identification Systems, Inc. 3
WandRdr1040.sxw 05/17/04
Mini-TracKer Wand ReaderTM
User's manual
Multi Mode Reader
Manufactured under one or more of the following Patents:
Other Patents Pending, U.S. and International
FCC ID: IOL-125-AV1040
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
WARNING: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment without approval of the
manufacturer could void the user's authority to operate this equipment.
For Information:
Within USA.....................................(800) 336-2843
Outside USA..............................(+1 951) 371-7505
Fax..................................................(951) 737-8967
http://www.AvidID.com
Support@AvidID.com
Avid Identification Systems, Inc.
3185 Hamner Avenue
Norco, California
USA, 92860
Copyright 2004 © Avid Identification Systems, Inc.
WandRdr1040.sxw 05/17/04
Introduction
Congratulations on the purchase of your new AVID Mini-Tracker Wand Reader. This
reader is capable of reading AVID and some other brands of electronic identification
tags using the FECAVA protocol.
Instructions
1. Power Button
Turn the reader ON by sliding the lower right hand button on the face of the reader,
forward. When the reader is powered on, it will emit a double beep sound and the
LCD will display AVID ID READY. To turn the reader OFF, slide the button back.
2. Read Button
Press the upper right button on the reader or the red button on the wand handle to
put the reader into the LOOKING mode. The LCD will display LOOKING. When a
microchip is found, the reader will emit two beep tones and display the number on
the LCD. If the read button is released before finding a microchip, the message NO
ID FOUND will display on the LCD.
3. Reading
The reader antenna is located in the round loop on the end of the wand handle.
This provides communications between the microchip and the reader. While
pressing down the Read button, rotate the antenna in a circular pattern while
moving down the animal’s back, starting from the back of the head.
Chip orientation plays a major role in optimum performance of the reader and
reading distances. In the figure below, CHIP A, in a parallel orientation to the
Copyright 2004 © Avid Identification Systems, Inc. 1
WandRdr1040.sxw 05/17/04
antenna, will achieve its maximum reading distance towards the center of the coil.
CHIP B, in the perpendicular orientation to the antenna, will achieve its maximum
read distance towards the outside edges of the antenna. It is therefore
recommended to move the antenna in a circular motion so that at some point you
are energizing the chip with a greater magnetic field making it easier to find the
microchip
The Wand Reader antenna, handle and switch are waterproof and can be
completely immersed underwater as long as the reader itself is kept out of the
water.
4. Battery
The reader is powered by one 9 volt battery. An alkaline battery is recommended
for a longer battery life. The battery is located in the battery compartment on the
lower backside of the reader. To replace the battery, slide the cover straight off. To
secure it, slide the cover back to it’s original position making sure the wires are
securely inside the compartment.
WARNING: FOLLOW BATTERY INSTRUCTIONS FOR DISPOSAL.
Operating the Reader Near Metal
Metal objects (especially ferrous metals) absorb electromagnetic fields. Operating the
reader antenna or placing the chip too close to metal object can severely limit the
range of operation of the system. If you are experiencing reduced operating range of
your system, check for metal tabletops, doors, etc. in proximity (a few inches) to any
part of the chip/reader environment.
Copyright 2004 © Avid Identification Systems, Inc. 2
WandRdr1040.sxw 05/17/04
Drawing 2 Best Read Orientation