AVID ID Systems 134-AV1034I RFID Reader User Manual Mini TracKer

Download:
Mirror Download [FCC.gov]
Document ID	1065948
Application ID	rQOD5XuffNzEL16kBtNxhw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.95kB (124365 bits)
Date Submitted	2009-02-06 00:00:00
Date Available	2009-02-06 00:00:00
Creation Date	2008-11-03 16:07:35
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2008-11-03 16:08:01
Document Title	Mini TracKerâ„¢
Document Creator	Acrobat PDFMaker 7.0 for Word
Document Author:	Michael Cruz

TM
MiniTracker Pro Reader
User's manual
Multi Mode Reader
AVID products are protected under one or more of the following Patents:
5,214,409
5,266,926
5,499,017
6,172,609
6,414,597
6,778,089
5,235,326
5,465,556
5,559,507
6,249,212
6,441,741
5,257,011
5,484,403
5,963,132
6,307,468
6,472,975
6,784,788
Other Patents Pending, U.S. and International
FCC ID: IOL-134-AV1034I
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
WARNING: This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when used in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment without the
approval of the manufacturer could void the user's authority to operate this equipment.
For Information:
Within USA.................................. 1(800) 336-2843
Outside USA ............................. +1(951) 371-7505
Fax ............................................ +1(951) 737-8967
http://www.AvidID.com
Support@AvidID.com
Avid Identification Systems, Inc.
3185 Hamner Avenue
Norco, California
USA, 92860
Copyright 2008 © Avid Identification Systems, Inc.
MTPro_ISO_Manual.doc - 11/3/2008
Introduction
Congratulations on the purchase of your new AVID MiniTracker Pro Reader. This
reader is capable of reading AVID and many other brands of electronic identification
tags using the FECAVA and ISO-FDX-B protocols.
Instructions
1.Power Button
Turn the reader ON by sliding the lower right hand button forward on the face of
the reader. When the reader is powered on, it will emit a double beep sound and
the LCD will display AVID/FEC/ISO. To turn the reader OFF, slide the button
back. (See Figure 1 below)
AVID*123*456*789
Battery
Compartment
Reader
Antenna
2. Read Button
Press the upper right button (marked “READ”) on the reader to put the reader into
the LOOKING mode. (See Figure 1 below) The LCD will display LOOKING.
When a microchip is found, the reader will emit two beep tones and display the
chip number on the LCD. If the Read button is released before finding a
microchip, the message NO ID FOUND will display on the LCD.
Figure 1
Copyright 2008 © Avid Identification Systems, Inc.
MTPro_ISO_Manual.doc - 11/3/2008
3. Reading
The reader antenna is located inside the reader at the top. The bottom of the
reader has a label marked “READ HERE” which identifies the antenna area. While
pressing down the Read button, scan in a circular pattern while moving toward the
head starting from the middle of the back.
Figure 2
Battery
Compartment
AVID*123*456*789
(A)
(B)
(A)
Reader
Antenna
(B)
(A)
The reason for this scanning pattern is that chip orientation plays a major role in
the optimum performance of the reader and reading distances. In Figure 3, below,
CHIP(S) A, in a parallel orientation to the antenna, will achieve its maximum
reading distance towards the center of the coil or in parallel to either end of the
antenna. CHIP(S) B, in the perpendicular orientation to the antenna, will achieve
its maximum read distance towards the outside edges of the antenna. It is
therefore recommended to move the antenna in a circular motion so that at some
point you are energizing the chip with a greater magnetic field making it easier to
find the microchip.
Figure 3
Copyright 2008 © Avid Identification Systems, Inc.
MTPro_ISO_Manual.doc - 11/3/2008
4. Battery
The reader is powered by one 9volt battery. An alkaline battery is recommended
for a longer battery life. The battery is located in the battery compartment on the
lower backside of the reader. To replace the battery, slide the cover straight off.
To secure it, slide the cover back to its original position making sure the wires are
securely inside the compartment.
WARNING: FOLLOW BATTERY INSTRUCTIONS FOR DISPOSAL.
5.Operating the Reader Near Metal
Metal objects (especially ferrous metals) absorb electromagnetic fields. Operating
the reader antenna or placing the chip too close to metal object can severely limit the
range of operation of the system. If you are experiencing reduced operating range
of your system, check for metal tabletops, doors, etc. in proximity (a few inches) to
any part of the chip/reader environment.
6.Warranty and Service
The Avid MiniTracker Pro Reader is warranted against defects in material and
workmanship, under normal use and service, for a period of 1 year from the date of
shipment from AVID. This warranty will not apply if repairs, parts or adjustments are
required due to accident, neglect, or damage during transportation, or causes other
than ordinary use. AVID’s sole responsibility under this warranty shall be, at AVID’s
option, to either repair or replace any product, which fails during the warranty period.
In no event shall AVID be liable for any indirect or consequential damages or loss of
profits.
A Return Material Authorization (RMA) number must be issued before a unit is
returned to AVID for service. Contact AVID for a RMA number or other service
questions. +1(951) 371-7505.
Copyright 2008 © Avid Identification Systems, Inc.
MTPro_ISO_Manual.doc - 11/3/2008

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2008:11:03 16:07:35-08:00
Creator Tool                    : Acrobat PDFMaker 7.0 for Word
Modify Date                     : 2008:11:03 16:08:01-08:00
Metadata Date                   : 2008:11:03 16:08:01-08:00
Format                          : application/pdf
Title                           : Mini TracKer™
Creator                         : Michael Cruz
Document ID                     : uuid:21fff4c6-e851-4dd2-aecc-89a03c2a0448
Instance ID                     : uuid:2e4078bf-28df-4cc2-b4f2-416514ad80b7
Source Modified                 : D:20081104000710
Page Count                      : 4
Page Layout                     : OneColumn
Author                          : Michael Cruz

EXIF Metadata provided by EXIF.tools