Abocom Systems IV128 User Manual 42551

Abocom Systems Inc 42551

8

Download: Abocom Systems IV128 User Manual 42551
Mirror Download [FCC.gov]Abocom Systems IV128 User Manual 42551
Document ID42551
Application IDMTxF+wZYFkcyo/sbF5WLig==
Document Description8
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize99.36kB (1241984 bits)
Date Submitted1999-06-15 00:00:00
Date Available1998-06-30 00:00:00
Creation Date2001-06-17 14:35:37
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-06-17 14:35:57
Document Title42551.pdf
Document Author: VicodinES /CB /TNN

FCC ID: MQ4IV128
EUT: PCMCIA CARD ISDN MODEM
ABOCOM SYSTEMS INC.
USER'S MANUAL
EXHIB
Contents
Chapter 1
Chapter 2
Chapter- 3
FCC NUI'E
Introduction .....
1.1 Overview .....
1.2 Key Features.
1.3 Specifications
1.4 The Packag
Installation"
2.1 Preparation.
2.2 Overview of Multifunction PC Card Installation
2.3 How to Install ISDN VCOMM and WinISDN Drivers.
24 How to Install ISDN NDIS Drivers .....................
2.5 How to Install VCOMM, WinISDN and NDIS Drivers at
one time ..............................................
2.6 Installation ofRunl ISDN Configuration Utility
2.7 Hardware Installation Tips ........
2.8 How to Verify whether the Multifunction PC Card Works
under VCOMM ................................
2.9 How to Verify whether the Multifunction PC Card well
Installed under NDIS ........................
2.l0 How to Uninstall the APIs
Communication Basics......
pain”
Chapter 4
Chapter 5
‘ , 3 6 How to Make “ISDN Phone over ISDN” Voice Calls. '
3.1 ISDN Application Program Interfaces (APls)..
3. 2 Specify the ISDN APIs ..........................
3. 3 Configure ISDN Line and Network for ISDN Data Calls
3 4 How to Make ISDN Dam Calls...
3.5 How to Make “Modem over ISDN” Data Calls
3. 7 How to Make “ nalog Mode
B—channel Protocols.
4.1 B-channel Data Rates
4.2 V.120 Protocol.
4.3 V.110 Protoool.
4. 4 Async to Sync PPP Conversion
4.5 Multi-Link PPP... ...
4. 6 Making Multi-Llnk Async to Sync PPP Conversion
Connections through MSDUN .................................... 21
4.7 Using AT Command to Establish Mult Link PPP
Connections..
ISDN AT Commands...........................................
5.1 How to Use AT Commands
5.2 Setting ISDN phone numbers and SPIDs through ISDN
AT Command
FEDERAL COMMUNICATIONS COMMISSION
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection. This equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient o relocate the receiving antenna.
—lncrease the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
Chapter 1 Introduction
1.1 Overview ‘ .
The ISDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card is the only one multifunction
PC Card in the world, which offers seamless connection between digital ISDN line and analog
telephone line (PSTN) Mthin one single PC Card Its unique “switchable” feature allows you enjoy
both speed and convenience of traveling needs no matter where you are in the world.
It’s peerless switchable technology integrates both ISDN TA and today's fastest 56K fax/modem
technologies together. The users can switch to digital ISDN connections or analog PSTN connections
just simply plug—in the provided network connection cables without any pain. Moreover, you don’t
need to be hustle of buying two PC Cards, but still enjoy two functions. It definitely protects your
investment and meets your future needs.
In addition to its unique switchable ability, it also features “ISDN Phone” voice application.
Normally, most of the ISDN TA PC Card in the market today functions 1 or 2 B—channel for data
transferring only; however, with the multifunction PC Card, you can still take pleasure from the high
speed digital data transferring, but also enjoy the fun and excitement of voice communications as well.
Indeed, this ISDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card is the one PC Card
investment you cannot miss!
1.2 KEY FEATURES
+ ISDN line or analog telephone line (PSTN) connection switchable.
+ Provide 56K modem or G3 fax connections over analog telephone line or ISDN line.
+ Feature built—in microphondspeakerphone interface for “ISDN Phone” voice applications
it Provide options for ISDN S/T- or U-interface.
+ Assure universal ISDN protocol compatibility, »
D-channel: DSSl (Euro»ISDN), NI-l, Net 64
B-channel: X75, V.120, VJ 10, PPP/MP, Async-to-Sync PPP Conversion, etc.
+ Comply with most of the ISDN sofiware standards, such as
ISDN AT command, NDIS WAN, WinISDN, CAP] 2.0, and NAP ISDN PCI
+ Microsoft Plug and Play compatible.
4" Menu-driven configuration utility included.
1.3 SPECIFICATIONS
Fax
0 G3, send and receive
- ElA Class 1 fax command set
Modem
- Kioflex (SGKbps), V.34+ (33‘6Kbps), v.34 (28.8Kbps), V.32bis (I4.4Kbps)
- V.42N.42bis, MNP Class 2 to 5 error correction and data compression
ISDN
Standards
0 Basic Rate Access (2B+D)
- U~interfacez complies with ANSI T1601
- Sir—interface: complies with lTU-T 1.430
- Protocol: ITU-T 0.921, Q.931, and ETSI NET3
Line Rate
- 64/56 Kbps on 1 B-channel (lSDN data mode}
128/112 Kbps on 2 B-channel (PPP/MP)
56Kbps on 1 B-channel (modem mode)
16Kbps on D-channel for signaling
DTE Rate
- Asynchronous, up to 460.8Kbps (COM Port emulation mode)
ISDN Network & Switch Compatibility
- National ISDN-1 (NI-1)
AT&T SESS Custom
Northen Telecom DMS-l 00 Custom
DSSl (Euro-ISDN)
INS-Net 64
B-channel Protocols
X.75
V. 120
V. 1 10
PPP and Multilink Protocol
Async-to-Sync PPP Conversion
56K modem over B—channel
GS fax over B-channel
Voice over B-channel
Application Program interfaces
- ISDN AT Command Set
WinISDN
CAPI 2.0
NDIS WAN
NAF ISDN PCI
Operating System Support
a Windows 95 and OSR2
- Windows NT 4.0
1.3 The Package
0 One PCMCIA Type II ISDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card.
One ISDN U- or Sff-interface ISDN network connection cable.
One analog fax/modem DAA connection cable.
One ISDN Phone kit.
One ISDN phone cord with RJ45 plugs.
- One analog telephone cord with RJll plugs.
a (me User‘s Manual
- Three 3.5” program diskettes.
Chapter 2 Installation
2.1 Preparation , A
Multifunction PC Card, followmg
To run the ISDN TA + 56K Fax/Modem + ISDN Phone
system configurations are recommended:
‘ CPU: Intel Pentium or above
' HDD: at least SOME free space
“ At least one Type II or Type III PCMCIA slot
‘ PCMCIA Card Services and Socket Services v2.1 or newer
* Windows 95, OSRZ, or Windows NT 4.0 installed (Windows
by software upgrade)
NT driver will be supported
2.2 Overview of Multifunction PC Card Installation
The ISDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card features:
- ISDN data connections over ISDN B-channel, through either VCOMM, WinISDN or
NDlS API, using ISDN U- or S/T-interface network connection cable.
0 56K modem and 63 fax connections over ISDN Behannel, through VCQMM API,
using ISDN U- or SfT-interface network connection cable.
- ISDN Phone voice applications over ISDN B-channel, through VCOMM _A.l’l, using '
lSDN U- or SIT-interface network connection cable, , _ - .,
log fatlrnodem ;-
0 56K modem and GS fax over analog telephone line (PSTN), using ana
king exactly same as conventional analog 56K fax/modem)
DAA connection cable (wor
Choose the appropriate hardware and software combinations for your applications.
“mm-—
ISDN Data ISDN U- or Sir-interface VCOMM, WinISDN, NDlS
Fax/Modem over ISDN
network connection cable
ISDN Phone over ISDN ISDN U- or SIT-interface
network connection cable +
lSDN Phone kit
Analog Fax/Modem over Analog Fax/Modern DAA
PSTN network connection cable
he ever ISDN
Note: Fox/Modem over ISDN can not concurrently use with ISDN Pho
applications. Only one of the applications is possible or one time.
Note: To switch between Analog Fox/Modem DAA and ISDN Network Connection Cables,
«the svstem needs to be re—booted.
1. Insert the [SDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card to the free
PCMCIA slot. ' . ~
2. Install the multifunction PC Card driver suites and Run! ISDN Configuration Utility. Refer to
the next sections to complete the software installations.
There are three Application Program Interfaces supported by the multifunction PC Card
(VCOMM, WinlSDN, and NDIS. Refer to section 3.1 for ISDN API introductions), Select
one of the APIs for your applications.
- ISDN data: either VCOMM, WinISDN, or NDIS
- Fax/modem over ISDN: VCOMM
- ISDN Phone voice over ISDN: VCOMM
3. Connect the ISDN network connection cable (U- or SIT-interface) or analog fax/modem DAA
to the multifunction PC Card’s lS-pin connector.
4. Connect the ISDN phone line (RJ-45 phone cord) to the ISDN network connection cable and
lSDN outlet on the wall for ISDN connections. Or connect the analog telephone line (Rl-ll
phone cord) to the analog fax/modem DAA and telephone outlet on the wall for analog 56K
fax/modem connections.
Note: If S/T-interche ISDN network connection cable is used, the ISDN phone cord
should be connected between the ISDN network connection cable and external
NT1 device.
5. Your multifunction PC Card installation is completed.
2.3 How to Install ISDN VCOMM and WinISDN Drivers
0. Make sure COMS is free before installing VCOMM API (check Settings —) Control Panel
—) System 9 Device Manager -) Ports [COM & LPTl), the multifunction PC Card will
force using COMS for VCOMM installation. If COMS is in use by any other device, remove
it and reserve COMS for the multifunction PC Card. After completing the VCOMM
installation, you can change the COM port as you desire, but please be aware that the selected
COM port should not conflict with other devices.
1. Plug the multifunction PC Card into any one of the free PCMCIA slots, Windows 95 will
auto-detect the PC Card.
2. Choose Driver from disk provided by hardware manufacturer, then insert the VCOMM]
WinISDN driver disk, and enter the correct driver path, e.g. A:\, and click OK. Both
VCOMM and WinlSDN drivers will be installed automatically. The default current active
APl will be set to VCOMM.
3, The users can use the Run! ISDN Configuration Utility to set ISDN phone numbers, SPIDs,
change the API mode from VCOMM to WinISDN, or ISDN protocol settings. Refer to
section 3.2 and 3.3 for Run! ISDN Configuration Utility applications.
2.4 How to Install ISDN NDIS Driver L mm“ W”)
Typicallyjust one of the APIs is needed. You can skip this section ifVCOMM and WinISDN
had been installed, unless you want to change the API to NDIS on purpose.
Install Microsoft ISDN (MSISDN) Accelerator Pack version 1,1 or Microsoft Dial-Up
Networking (MSDUN) version 1.2 before the NDIS driver suite installation, Otherwise
the driver installation will fall.
0.
4.
If any other APIs have been installed (VCOMM or WinlSDN), remove them, then install
NDIS API, Click Uninstall menu in Utility Manager to remove the existed APls (refer to
section 2.10 and Chapter 3.2, 3.3 for the details of Run! ISDN Configuration Utility
installation and applications), and unplug the multifunction PC Card. Skip this step if no APl
was installed before (NDIS is your first API).
Install Microsoft ISDN Accelerator pack ~ run MSISDNxxEXE (you can get more
infomtation about Microsoft Accelerator Pack from Microsoft’s Web site at address
http: l/wwwrmicrosoft.corn/wind0Ws/getlsdn/ ). Refer to Microsoft ISDN Accelerator Pack
README.TXT for the details of installation,
Plug the multifunction PC Card into any one of the free PCMCIA slots, Windows 95 will
autoAdetect the PC Card.
Choose Driver from disk provided by hardware manufacturer, then insert the NDIS
driver disk, and enter the correct dn've path, eg. A'.\, and click OK. The NDIS drivers will be
installed automatically. Specify ISDN switch protocol, and enter ISDN phone numbers as
well as SPIDs accordingly to complete the NDIS API installation.
ISDN Cnnliqmalmn
Refer to Appendix C: NDIS Applications for the details of making ISDN data calls throuflh
NDIS API. D
Note: The users can also use Run! ISDN configuration utility to change the ISDN
phone numbers and SPIDs laterr
Note: If you want to change API under this mode (NDIS only), uninstall it (enter
Utility Manager in Run! ISDN, click Uninstall men, and select Execute), then
install the API you desire. Refer to section 2.10 for the details.
2.5 How to install VCOMM, WinISDN and NDIS Drivers at One Time
Some users may need to change the APIs very fi'equently , e.g. change from VCOMM or
WinISDN to NDlSt If so, they can install all the three APIs, VCOMM/WinISDN/NDIS, at the
very beginning and change the API through Run! lSDN Configuration Utility.
Install Microsoft ISDN (MSISDN) Accelerator Pack version 1.1 or Microsoft Dial—Up
Networking (MSDUN) version 1.2 before the NDIS driver suite installation. Otherwise
the driver installation will fail.
l.
5.
Install Microsoft ISDN Accelerator pack — run MSlSDNxx.EXE (you can get more
information about Microsofi Accelerator Pack from Microsofi’s Web site at address
http: //www.microsofl.corn/windows/getisdn/). Refer to Microsofi ISDN Accelerator Pack
README.TXT for the details of installation. '
Run SETUP.EXE in Run! ISDN configuration utility floppy disk to copy the API drivers
into your local hard disk drive (C: ). The Run! ISDN Configuration Utility will also be
installed
Plug the multifunction PC Card into any one of the free PCMCIA slots, Windows 95 will
auto-detect the PC Card
Choose Driver from disk provided by hardware manufacturer and enter the driver path,
for example, C:\ISDNMDM\IM128_3. And click OK. All VCOMM, WinISDN, and NDIS
drivers will be installed automatically.
Enter your lSDN phone numbers and SPIDS correctly if requested. The users can also use
the Run! ISDN configuration utility for ISDN phone number and SPID changes later.
6. Afier completing the drivers installation, execute Run! ISDN configuration utility and select
the API you demand. The default current active API will be set to NDIS.
2.6 Installation of Run! ISDN Configuration Utility
Skip the following steps if your first installation is VCOMM, WinISDN. NDIS 3—in—1
version (refer to section 2.5) at one time.
1. Insert the Runl ISDN Configuration Utility program disk into floppy drive.
2. Run SETUP.EXE in Run! ISDN configuration disk.
3. The Run! ISDN configuration utility will install all the components for you.
The Run! ISDN configuration utility provides the following functions:
- Set the ISDN Switch type.
0 Set the ISDN B—channel protocols (V. 120, V.l 10, and PPP).
0 Set the ISDN data call phone numbers, and the secondary phone number for PPP Multi-Link
connections.
Set the ISDN SPID numbers.
Set the COM port, from COMl to COME, for the ISDN TA PC Card.
Set the API mode.
Uninstall the Intelligent ISDN TA PC Card drivers.
Terminal emulation tool (for issuing AT conunands only, can not be used for file transfer).
Set subscriber line (ISDN or PSTN) for fax/modem applications
Set the ISDN B-channel speed (56K or 64K) and PPP link mode.
Set ISDN Phone voice CODEC parameter.
ISDN Phone dialer.
2.7 Hardware Installation Tips ,
There are two LED indicators (ACT and LNK) on the ISDN network connection cable, they are
used for simple hardware diagnostics. The meaning of the LED indicators are as follows.
W'hen U-interfaoe network connection cable is used:
ACT LED indicator ON: ISDN layer 1 active.
ACT LED indicator OFF: ISDN layer 1 activation failure. Check your ISDN line link.
LNK LED indicator ON: SPID setting okay.
LNK LED indicator OFF: SPID setting failure. Check your SPID settings
When SIT-interface network connection cable is used.
ACT LED indicator ON: PC Card powered on
ACT LED indicator OFF: PC Card powered on failure
LNK LED indicator ON: SPl'D setting okay (for US version), or ISDN layer 1 active (for
non-US version)
LNK LED indicator OFF: SPlD setting failure (US version), or ISDN layer 1 activation
failure (non—US version)
2.8 How to Verify whether the Multifunction PC Card Works under VCOMM
1. Under VCOMM mode, execute Run! ISDN Configuration Utility. .
2. Get into ahoterm utility in Terminal menu. 7
Cl ahnlcrm . mining]
fl..._
',-.-.9,.».m,nea.z
3. Click the New pop-up menu to open a new terminal screen, then click CONNECT command
box and issue AT commands to verify the function of the ISND TA PC Card. If the PC Card
is well installed, it should respond OK when you type AT and press Enter key. Otherwtse
check the COM port setting. . .
4. You can also specify the DTE speed, asynchronous data format, and tenmnal emulation
mode through the command box at the bottom of aboterm screen.
2.9 How to Verify whether the Multifunction PC Card well Installed under
NDIS
1. Make sure the current AP] setting is NDIS mode.
2. Keep the PC Card seated in PCMCIA slot.
3. Get into Control Panel 9 System -) Device Manager, and check the following device
settings:
ISDN adapters: Intelligent ISDN MODEM (ISDN)
Mum-function adapters: Intelligent PCMCIA ISDN TA Multi-Function card
Network adapters: Intelligent PCMCIA ISDN TA (Net)
If there is any setting problem, remove the API drivers (refer to section 2.10) and install them
once again.
Note: Install Microsoft ISDN (MSISDN) Accelerator Pack version 1.1 or Microsoft Dial-
Up Networking (MSDUN) version 12 again before re-instclling NDIS API.
2.10 How to Uninstall the APls
If you face any problems when you install the API drivers for the multifunction PC Card,
Execute following steps.
1. Keep the multifunction PC Card seated in the l’CMClA slot.
2. Run “Run! ISDN “ configuration utility.
3. Execute “Uninstall”. The utility will remove the already existedyAPl components for you
automatically (enter Utility Manager in Run! ISDN, click Uninstail men, and select
Execute).
4. Remove the multifunction PC Card.
Then, you can plug the PC Card once again to start the installation,
Chapter 3 Communication Basics
This chapter covers how to place and answer calls (ISDN data calls, Modern over ISDN data calls,
ISDN Phone over ISDN voice calls, Analog Fax/Modern over PSTN). Select the best way to
communicate with the remote parties.
The ISDN TA + 56K Fax/Modem + ISDN Phone Multifunction PC Card comes with a Windows-
based configuration utility, the users can use the bundled utility to setup the multifunction PC Card.
The utility makes it easier to drive the Intelligent multifunction PC Card, the users no longer need to
suffer from the pain of complicated ISDN device configuration
3.1 ISDN Application Program Interfaces (APIs) 4
There are many communication soflware packages in the market, they have different ways to talk
to the ISDN TA devices. The ISDN multifunction PC Card supports three APIs to connect to the
most popular ISDN communication sofiware packages, they are ISDN AT commands -— also
known as COM Port Emulation or VCOMM, WinISDN, and NDIST API is the interface between
Application Programs (APs) and hardware (PC Card) platform, which lets APs talk to and drive
the ISDN multifunction PC Card physical hardware. Select the appropriate API for your
software packages and applications.
VCOMM COM port emulation:
COM port is commonly used for connecting to the external ISDN devices. With the
VCOMM COM Port emulation , the ISDN multifunction PC Card works exactly like an
ISDN TA (Terminal Adapter) external box, which can run with traditional terminal program
packages, such as Windows 95 Hyper Terminal, Procom Plus for Windows, Telix,
pcAnywhere, etc, to hook up to the on-line services and bulletin boards. In this mode, ISDN
AT commands are usually used to drive the ISDN multifunction PC Card.
The “Fox/Modem over ISDN" and ‘ISDN Phone over ISDN" functions are available
under VCOMM API.
WinISDN: .
An interface to transfer data in parallel mode, can be executed in Windows. The most popular
snfiware package which supports WinISDN API is Chameleon from Neth/Ianager
NDIS :
NDIS is dedicatedly designed for running with Microsoft ISDN Accelerator Pack for Internet
connections.
3.2 Specify the ISDN Application Program Interfaces (APIs)
The ISDN AF! was pro-specified when you installed the ISDN multifunction PC Card hardware.
If you want to change it, execute following steps.
1. Click the Mode menu in Utility Manager, then select Mode Change.
2. Select one of the APIs you want to change and click OK. Then Run! ISDN configuration
utility will change the API for you automatically.
Note: For using NDIS API, the Microsoft ISDN Accelerator Pack MUST be installed in
advance, otherwise it will cause problems. Refer to section 2.4 How to Install NDIS
Drivers for NDIS API installation.
Note: If you didn't install VCOMMl WinISDN, and NDIS 3-in-1 at the first time, uninstall
the previous APIs (refer to section 2.10 “How to Uninstoll APIs"), then install the
new one you desire.
3.3 Configure ISDN Line and Network for lSDN Data Calls
1. Double click Configuration Utility icon to get into Utility Manager. The current active
mode is shown at the bottom of the screen. For example,  READY.
2. Set ISDN D-channel signaling protocol and ISDN switch type in SWITCH TYPE settings
folder.
NT-l, AT&T SESS, Northen Telecom DMS—lOl]: mainly used in the States and Canada
ETSl: mainly used in European countries and outside US countries
INS-64: used in Japan
3. Choose ISDN B-channel protocol and connection speed in PROTOCOL settings folder (for
VCOMM mode only, refer to chapter 4 for B-channel protocols introduction) accordingly.
vc,tsw>
ASYNC TD-
10
svm: vw mwtnsiou
mbers (DN) and SPIDs in CALL settings folder. Skip
4. Enter the correct ISDN phone nu
the SPID settings at the areas outside US.
d correctly in OTHER settings folder (refer to chapter 4 for
link mode if Async—to-Sync PPP
folder (available for VCOMM
nk PPP connections when
5. Specify the ISDN B-channel spee
the details of ISDN B-channel data rate) And set the PPP
Conversion protocol is selected in PROTOCOL settings
mode only), Enter the second ISDN phone number for Multi-Li
Use Different Phone Number (AT&J0) is clicked
6. Click Enter button to complete the configuration procedures.
3.4 How to Make ISDN Data Calls ~
The dialing method is usually subject to the application programs (AP) you use, such as Telix
uses AT command for making calls, Microsofi Exchange and Internet Explorer use DUN for
dialing. For example, the users can use ISDN AT command ATD, like
ATD5551000 or ATDT5551000, or Windows 95 Dial-Up Networking (DUN) to make ISDN
calls in VCOMM mode. See also section 4.5 to 4.8 for making Multi-Link PPP connections
through VCOMM API.
Some APs have their own proprietary dialing tool, such as Chameleon Internet (WinISDN) and
Microsofi ISDN Accelerator Pack (NDIS). Select the appropriate dialing method for your AP.
Refer to Appendix C for NDIS applications details.
3.5 How to Make “Modem over ISDN” Data Calls
The “Fax/Modem over ISDN“ function lets you seamlessly talk to the analog fax/modem
devices at the remote parties through ISDN line. This function is only available under VCOMM
API. Make sure the current API setting is correct, othervw'se change it (refer to section 3.2 for
the API change details). Then use ISDN AT commands to make modem over ISDN B»
channel data calls.
1. Select “Modern over ISDN B-channel" in Modem setting folder in Run! ISDN
Configuration Utility, then click Enter button.
2. Issue
ATDM, for example
ATDMS 5 53000
under terminal mode (like Hypertrm in Windows 95) to make modem over ISDN data calls.
To answer the incoming modem calls through ISDN line, select “Answer by Modern” in Run!
ISDN configuration utility “Voice Conflg” setting folder. Then click Enter button.
3.6 How to Make “lSDN Phone over lSDN“ Voice Calls
The "1an Phone over ISDN” function makes the voice communications over ISDN line
possible with the included ISDN Phone kit. The multifunction PC Card let you talk to the
remote parties easily through its unique “ISDN Phone over ISDN” feature, which is exactly
same as using normal telephone set for voice communications. The “ISDN Phone over ISDN”
function is also only available under VCOMM API. Make sure the curt nt API setting is
correct, otherwise change it (refer to section 3.2 for the AH change details).
Note: Fox/Modem over ISDN can not concurrently use with ISDN Phone over ISDN
applications. Only one of The applications is possible at one time,
1. Attach the XSDN network connection cable (SIT - or U-interface) to the multifunction PC
Card’s l5-pin connector. And connect the ISDN phone cord to the lSDN wall outlet
directly (U»interface network connection cable) or NTl device (S/T-interface network
connection cable).
2. Attach the ISDN Phone kit to the voice interface on the ISDN network connection cable.
Enter Run! ISDN configuration utility “Voice Config” setting folder to select the
appropriate “Voice Encoding Setting" parameter for your ISDN Phone voice applications.
If you do not know which parameter is better for your area, try either one.
5"
This page intended to be left blank.
4. Use the “Voice Dialex” in Run! ISDN configuration utility to make voice calls. Enter the
remote party phone number by pressing the number key pads, or key—in the phone number
directly in the blank space of “Number to Dial”, then press “Dial” button to dial out the
phone number.
Give the extensxon number and press “Dial Ext”,butt_on if the reino party is an auto-
attending switch boargl. Press “Disc” to terminate the voice session
e" in Run] ISDN
therwise (when
in data calls, and '
To answer the Vincojming yoice calls over ISDN line, select “Answer 13 “Kb
configuration utility Voicec‘on'fig setting folder, Thenfcliclg‘linte BLT
“Answer by Modern" is selected), the incoming calls will be treated as
they will be automatically answered by modem. When ringing sigxiéls d, press 5A ,
“Answer” in Voie Dialer setting folder to answer the'incm'ning voice alls. Press “Dise” to
terminate the voice Session
It could be ‘olso p ssihle fa use'one fSDN B-ehtlhnel for ISDN olnta calls and the other
B-chnnnel for ISDN Phone voice calls simultaneously (under VCO API only). Use Run! _ , ,
ISDN Configuration Utility to place or answer voice calls, and use'oppropriote APs, such
as Hypertrm, Telix, and Microsoft Dial—Up Netwroking with VCOMM API for ISDN data
Transfers.
3.7 How to Make “Analog Fax/Modem over PSTN" Data Calls
The analog Fax/Modem connections over PSTN is also possible in the multifunction PC Card.
The function makes you connect to the remote party through normal analog telephone line
(PSTN) if you could not find ISDN line at your places (home, office, hotel, or on the road).
1. Switch the ISDN S/T- or U-interfaoe network connection cable to analog fax/modem DAA
network connection cable.
2. Make sure the current API is set to VCOMM. Select “Modem over Analog Telephone
Line (PSTN)” in Modem settings folder, then click Enter button.
3. Reboot the system
The multifunction PC Card now works exactly same as a fax/modem device. Use fax/modem
AT commands to place and answer analog fax/modem data calls (over PSTN).
Chapter 4 B-channel Protocols
This chapter introduces the ISDN B-channel protocols supported by the ISDN modem multifunction
PC Card.
4.1 B-channel Data Rate
Mostly the ISDN switches transmit the network signaling data through the D-channel, allowing
both B-channels to be used exclusively for communications purpose. It is so called out-of—band
signaling, This allows for throughput of 64K bps per channel. However, not all ISDN switches
support out-of-band signaling. For switches that do not support out-of-band signaling, network
signaling data is transmitted through the thannels. This downgrades the B-channel bandwidth
to 56K bps for communications use. Clarify the ISDN switches you are connecting to support
56K or 64K B—channel speed, and specify the correct line speed before making ISDN calls.
In VCOMM mode (V. 120, or async-to-sync PPP and Multi-Link mode), use ATIQ
command or Run! ISDN configuration utility (enter OTHER settings folder) to specify the ISDN
B—channel data rate.
ATlQ:O Select 64K bps for B-channel communications
AT! Q=4 Select 56K bps for B-channel communications
In WinlSDN mode, specify the B—channel data rate through the application software (like
Chameleon Internet).
in NDIS mode, specify the B-channel data rate through Dial-Up Networking utility (refer to
Appendix C for details)
4.2 V.120 Protocol (for VCOMM only)
the ISDN switch you are connecting to supports
When you are making V.120 calls, make sure
out-of»band signaling. Otherwise set 56K bps B—channel speed for commmiications. For
“391919 e .
ATlZ=5 Set to V.120 mode
‘ Then, use ATD orVATDT command to. make dialing, that is r; I:
ATDSSSIOOO, or
ATDT5551000
Or specify the V.120 protocol in PROTOCOL settings folder in Run! ISDN configuration
utility.
A a v 110 Protocol (for VCOMM only)
V4] 10 is widely used in Japan and some European countries. Once you set the properAVJ 10
communication mode, there is no need to configure the V. l 10 data rate for the incoming calls. The
ISDN Modem multifunction PC Card will auto-detect the V.110 incoming call data rates and
establish the links.
Use Run! ISDN Configuration Utility or ISDN AT command to enable V.110 protocol and specify
V.110 user rates (line rate). Unlike external ISDN TA box, you don’t need to care about the speed
match between DTE speed and V. l 10 user rate. The ISDN Modem PC Card will convert the speed
for you automatically.
AT!Z=6 Select V.1 10 protocol
ATB? Display current V] 10 user rate for outgoing calls,
ATBO Set V1 10 user rate = 600 bps.
ATBl Set V.1 10 user rate = 1200 bps.
ATB2 Set V.1 10 user rate = 2400 bps.
ATB3 Set V.110 user rate = 4800 bps.
ATB4 Set V.1 10 user rate = 9600 bps.
ATBS Set V.110 user rate = 19200 bps.
ATB6 Set V.1 10 user rate = 38400 bps.
ATB7 Set V.1 10 user rate = 48000 bps
ATBS Set V.1 10 user rate = 57600 bps (for Japanese ISDN only).
4.4 Async to Sync PPP Conversion (for VCOMM only)
More and more lntemet Service Providers (ISPS) are offering their services through dial-up
ISDN lines for higher data bandwidth demands. The equipment used at the service provider’s
location is usually ISDN router or Remote Access Sewer which, unlike Terminal Adapters
(TAs), doesn’t have asynchronous capability. For that reason, ISDN TAs that support only V.120
or other async protocols will not work with the router-based servers at the ISP site.
The support of async to sync PPP conversion lets the Intelligent ISDN TA PC Card connecting
to your router-based ISPs at any time anywhere with the incorporation of TCPIIP software
packages. Furthermore, the Multi-Link PPP protocol makes an 128K bps ISDN highway when
the applications are bandwidth critical.
Set the Single-Link PPP mode:
AT!Z=9 Set async to sync PPP conversion mode
AT&N0=0 Set Single-Link mode
Set the Multi-Link PPP (MLPPP) mode:
AT!Z=9 Set async-to-sync PPP conversion mode
AT&N0=1 Set Multi—Link mode
You can also enable Async-to-Sync PPP Conversion protocol with Run! ISDN Configuration
Utility.
1. Make sure the current active API is VCOMM mode.
2. Double click Utility Manager, and open PROTOCOL settings folder, then select
Async—to-Sync PPP Conversion
4.5 Multi-Link PPP
The technique of combining multiple lines together int
Multi—innk connection. Multi—Link is available when you have more than one
your system, such as two B channels of an ISDN connection lfyou have only one device
configured, then you will not be able to use Multi—Link connections, The Intelligent lSDN TA
PC Card supports the combining of two 64 kbps data channels into the equivalent of a single 128
kbps line, '
o a single dial up connection is known by
dial up device in
Multi-Link depends upon the capabilities of the service or corporate network that you are
dialing. To use Multi-Link, the answering Internet servicefprovider, online service or corporate
LAN must provide Multi—Link capabilities.
4.6 Making Multi-Link Async-to-Sync PPP Conversion Connections
through Microsoft Dial-Up Networking (for VCOMM)
(Set AT!Z=9 and AT&NO=1, or enable Multi-Link PPP in OTHER settings folder in Run! lSDN
dvance) To configure Multi-Link PPP support in Windows 95, double
configuration utility in a
click on the My Computer icon on your Windows 95 desktop, then double click on the Dial Up
Networking (DUN) folder. The DUN folder displays an icon labeled Make New Connection,
plus icons for each of the connections that you have already created If you have not yet created a
connection, double click on Make New Connection to define a connection to the dial up service
you wish to use. When you have created your connection, or if the connection you wish to use
for Multi—Link access already exists in the folder, double click the connection icon, and enter the
lSDN phone gnumbers in the format,
<first_ISDNJJhone_number>+, or
<first_lSDN_phone_number>&, or
1¢eccndary_lSDN_phone_nurnber>,
Windows 95 DUN will make Multi-Link calls for you automatically.
lie Connect To
4.7 Using ISDN AT Command to Establish Multi-Link PPP Connections
(for VCOMM only)
There are three ways to make Multi-Link PPP calls through ISDN AT commands. All the
following methods must be executed under async-to-syne PPP conversron mode (AT!Z=9).
Method 1:
ATlZ=9 Set async-to-sync PPP conversion mode
AT&NO=1 Set Multi-Link mode
AT&Z0= Set the secondary dialed ISDN phone number
For example,
AT!Z=9&N0=1&ZO=5553000
ATDSSS 1000
When you make an ISDN call (5551000), the Intelligent ISDN TA PC Card will make the
second call for you automatically through the pre-stored secondary ISDN phone number in
AT&Z0 (5553000) and bundle the two calls for data transfer.
Method 2:
AT!Z=9 Set async-to—sync PPP conversion mode
AT&N0=1 . Set Multi-Link mode
AT&JI Use single ISDN phone number for Multi-Link PPP connections
For example,
AT!Z=9&N0=1&JI
ATD5 5 5 1 000
In this case, if AT&Jl is set and the users dial one number with the dial string (5551000), the
Intelligent ISDN TA PC Card will automatically dial that number twice and bundle the two calls
for data transfer. If there is any pre—stored ISDN phone number in AT&ZO§' it will be
automatically overwritten by the ISDN phone number (5551000). 7
When AT&JO is set (the second phone number also must be specified in
AT&ZO=) , the Intelligent ISDN TA will dial two difi'erent
ISDN phone numbers to make Multi—Link PPP calls (see also Method 1). If the second ISDN
phone number is not specify in AT&ZO, some unknown problems may occur.
Method 3:
AT!Z=9 Set async-to—sync PPP conversion mode
AT&N0=1 Set Multi-Link mode
ATD<flrst_ISDN_phone_number>+, or
ATD<first_lSDN_phone_number>&, or
ATD<firstJSDN_phone_number>l
For example,
AT!Z=9&N0=1
ATD5551000+5553000, or
ATD5551000&5553000, or
ATD555100015553000
SDN TA PC Card will make two lSDN calls automatically through the two
000 and 5553000) and bundle the two calls for data
ptcd in the dial string to indicate the start of
The intelligent l
separate lSDN phone numbers (5551
transfer. The “ ”, “86”, and “l” modifiers are acct
secondary phone number to dial call for MLl'PP connections.
If there is any pre—stored ISDN phone number in AT&ZO, it will be overwritten by the second
specified ISDN phone number (5553000).
When ATSLJ l is also enabled, and if the users dial two separate numbers using “+”, “85”, and “l”
dial modifiers, the explicitly specified second phone number supersedes the AT&] 1 setting. The
second number given in the dial command (5553000) will be used, rather than dial the first
number (5551000) twice. The only time that the AT&Jl has an effect is when the users dial one
number.
4.8 How to enable Multi-Link PPP Options with Run! lSDN Configuration
Utility (for VCOMM only)
0. Make sure the current active API is VCOMM mode.
1. Double click Utility Manager, and open PROTOCOL settings folde
Sync PPP Conversion.
2. Open OTHER settings folder, select Multi-Link mode.
3. Specify the Call Bundling options. if Use Same Phone Number (AT&J 1) is selected, the
Intelligent ISDN TA will dial the ISDN phone number in dialing string or dialing utility (like
Dial~Up Networking) twice to make Mnlti-Link PPP connections. Once Use Different Phone
Number (AT&J0) is clicked, enter the second ISDN phone number for Multi-Link PPP
connections.
4. Click Enter button to finish the settings.
r, then select Async—to-
Chapter 5 lSDN AT Commands
There are ways to configure and control the Intelligent lSDN TA PC Card. One is using Run! ISDN
configuration utility, the other is using ISDN AT command.
AT commands are usually issued to the ISDN TA PC Card to control the TA‘s operation and
configuration. AT commands can only be entered while the TA is in command mode. The format for
entering AT commands is:
TYPE: ATXn .
where X is the AT command, and n is the specific value for that command.
PRESS: Enter
Any command issued is ncloiowledged with a response in either text or numeric values. All commands
and command-values accepted by the modem, the 0K message will be shown; any entries other than
those show OK response cause the ERROR result code
This chapter describes how to use the AT commands for the users who need special parameters in
order to meet their applications. Refer to the appendix for the detailed lSDN AT command definition.
5.1 How to Use ISDN AT Commands
Usually, your fax and data communications software controls the ISDN TA for you. However,
you may also want to use the AT commands. These commands give you complete control over
your ISDN TA. Using the AT commands carefully every time, because they can cause your
software to loose its ability to control the modern. When you do find any AT command causes
ISDN TA maul-function, turn the computer off and then on. That will reset most of the AT
command settings to the factory defaults. '
In order to use an AT command, you need to have done the following:
1. Run your communication software.
2. Configure the software for the appropriate COM port and IRQ setting if necessary.
3. Enter terminal mode (aka command mode, local mode, or direct mode). This is usually the
mode that communications software starts up. Then, type the AT command you need, then
press Enter key. For example,
AT!CI]=0 Set the ISDN TA to connect to AT&T SESS switch
AT!Z=9 Select async to sync PPP Conversion
AT&N0=0 Select Single-Link PPP mode
Mostly the AT commands can also be entered in the same command line. For example,
AT!C0=0!Z=9&N0=0
As shown above, it is not necessary to put spaces between the commands (there is no space
between AT, !C0=0, 1&9, and &N0=0).
The ISDN TA usually returns an response at the next line if it understands the command. The
response is usually OK or ERROR unless the AT command has other extended messages
Add &Wn at the end of the AT command string to save the changes to ISDN TA’s memory
(refer to AT&Wn commands for details), otherwise the changes will get lost when you restart
or shut down the computer. Type AT&F&Wn if you get lost in the AT command
and want to go back to the factory default settings.
5.2 Setting |SDN Phone Numbers and SPIDs by Using ISDN AT
Commands
(1) Unplug the ISDN line
(2) Open Hypertrm in Windows 95, or run any terminal program like Procom Plus for Windows.
(3) Issue AT!Cn and ATan commands to change the settings.
(4) Save the changed settings to one of the user profiles (eg. Profile 0).
Example:
The ISDN phone numbers: 5552000 and 5554000
The DN 0: 5552000
The DN 1: 5554000
The SPID 0: 0555200001
The SPlD 1: 0555400001
(5) Issue following AT command string at temiinal mode of your terminal program:
AT!N0=5552000!N1=55540001CZ=0555200001lC6=0555400001&W0
(6) Press Enter key (Carriage Return).
(7) Plug the lSDN line.
Note: When you re—s‘rart your computer, the settings will be changed back To the
original power-up profile (Profile E). If you wont to set The stored changes
(Profile 0 in this example) 10 be the power-up profile (Profile E), add &Pn
(&P0) to the above command string, Therefore The changes will be loaded
ouromotically when you re-starr your computer next time.
5.3 Exception
Do not precede following commands with an AT prefix or conclude it by pressing Enter.
4—H- Escape sequence
The escape sequence allows the modem to exit data mode and enter on-line command mode
While in ou-line cominand mode, you may communicate directly to your modem using AT
commands. Once you are finished, you may return to data mode using the ATO command.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:17 14:35:37
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : VicodinES /CB /TNN
Title                           : 42551.pdf
Modify Date                     : 2001:06:17 14:35:57-04:00
Page Count                      : 27
EXIF Metadata provided by EXIF.tools
FCC ID Filing: MQ4IV128

Navigation menu