Abocom Systems WR5201 802.11 b/g/n Wireless Broadband Router User Manual WR5201 Eng Manual ok

Abocom Systems Inc 802.11 b/g/n Wireless Broadband Router WR5201 Eng Manual ok

User Manual

1 802.11n/b/g Wireless Broadband Router User’s Guide
Table of Content CHAPTER 1: INTRODUCTION............................................................................................4 Features..............................................................................................................................4 CHAPTER 2: ABOUT THE OPERATION MODES............................................................5 Access Point Mode.............................................................................................................5 Gateway Mode...................................................................................................................5 CHAPTER 3: CONFIGURATION .........................................................................................6 Login...................................................................................................................................6 Common Connection Types ......................................................................................... 7 Setup Wizard .....................................................................................................................9 Configuration via Web......................................................................................................9 Operation Mode............................................................................................................ 9 Internet Settings ..............................................................................................................10 WAN (Wide Area Network) Settings......................................................................... 10 LAN (Local Area Network) Settings.......................................................................... 15 DHCP Clients ............................................................................................................. 16 Wireless Settings..............................................................................................................16 Basic ...........................................................................................................................17 Advanced.................................................................................................................... 19 Security....................................................................................................................... 20 WPS............................................................................................................................ 22 Station List.................................................................................................................. 23 Firewall.............................................................................................................................23 MAC Filtering ............................................................................................................ 23 Access Control............................................................................................................ 24 URL Filtering ............................................................................................................. 25 Port Trigger................................................................................................................. 26 Virtual Servers............................................................................................................ 27 DMZ ........................................................................................................................... 28 Denial of Service ........................................................................................................ 28 Administration.................................................................................................................29 User/ Password ........................................................................................................... 29 Time Zone Setting ...................................................................................................... 30 System Log................................................................................................................. 31 DDNS ......................................................................................................................... 31 Upload Firmware........................................................................................................ 32 Settings Management.................................................................................................. 33 Statistics......................................................................................................................34 CHAPTER 4: PC CONFIGURATION.................................................................................35 Overview ..........................................................................................................................35 Windows Clients..............................................................................................................35 TCP/IP Settings - Overview ....................................................................................... 35 Checking TCP/IP Settings - Windows 2000............................................................... 36 Checking TCP/IP Settings - Windows XP.................................................................. 37 Internet Access ........................................................................................................... 38 Macintosh Clients............................................................................................................40 Linux Clients....................................................................................................................40 Other Unix Systems.........................................................................................................40 Wireless Station Configuration......................................................................................41 APPENDIX A: TROUBLESHOOTING..............................................................................42 Overview ..........................................................................................................................42
3General Problems............................................................................................................42 Internet Access.................................................................................................................42 Wireless Access................................................................................................................ 43 APPENDIX B: ABOUT WIRELESS LANS........................................................................44 BSS....................................................................................................................................44 Channels...........................................................................................................................44 Security.............................................................................................................................44 Wireless LAN Configuration..........................................................................................45 Regulatory Approvals.....................................................................................................46
4Chapter 1: Introduction The 802.11n/b/g Wireless Broadband Router is a draft 802.11n/b/g compliant Wireless Broadband Router with 4-port Fast Ethernet Switch. With the advanced MIMO technology, it can support the data transmission rate 6 times more (up to 300Mbps) and the coverage 3 times more than IEEE 802.11b/g devices. Router enables your whole network sharing a high-speed cable or DSL Internet connection. The incredible speed of 802.11n/b/g Wireless Broadband Router makes it ideal for media-centric applications like streaming video, gaming, and Voice over IP technology, ensure optimum performance and maximum coverage with three external antennas. With 802.11n/b/g Wireless Broadband Router, you can share a high-speed Internet connection, files, printers, and multi-player games at incredible speeds, without the hassle of stringing wires. 802.11n/b/g Wireless Broadband Router offers easy configuration for your wireless network in the home and presents wireless network to you home of high functionality, security, and flexibility. Features 1. Support the IEEE 802.11n/b/g standard, high speed date rate up to 300Mbps. 2. Support WPS (Wi-Fi Protected Setup) with reset button. 3. High security with build-in Security: WEP 64/128, WPA, WPA2, 802.1x and 802.11i. 4. Support Gateway and AP mode. 5. Advanced Quality of Service (QoS) - 802.11e, WMM. 6. Easy configuration for home user setup. 7. MAC and Port filtering.
5Chapter 2: About the Operation Modes This device provides operational applications with AP and Gateway modes, which are mutually exclusive. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can use the web-based utility provided by the manufacturer as described in the following sections. Access Point Mode When acting as an access point, this device connects all the stations (PC/notebook with wireless network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. Gateway Mode When GW mode is selected, the Router will enter the gateway mode. And the wireless connection will be set up from a point-to-point local LAN into a point-to-multipoint WAN.
6 Chapter 3: Configuration Login 1. Start your computer. Connect an Ethernet cable between your computer and the Wireless Router. 2. Make sure your wired station is set to the same subnet as the Wireless Router, i.e. 10.10.10.254 3. Start your WEB browser. In the Address box, enter the following: http://10.10.10.254 4. Please enter the username “admin” and the password for login. The configuration menu is divided into four folders: Internet Settings, Wireless Settings, Firewall, and Administration. Click on the desired setup item to expand the folder in the main navigation page. The setup pages covered in this utility are described below.
7 Common Connection Types Cable Modems Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. Usually, none. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. Some ISP's may also require you to use a particular Hostname, Domain name, or MAC (physical) address. DSL Modems Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. None. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. PPPoE You connect to the ISP only when required. The IP address is usually allocated automatically. User name and password.
8PPTP Mainly used in Europe. You connect to the ISP only when required. The IP address is usually allocated automatically, but may be Static (Fixed). • PPTP Server IP Address. • User name and password. • IP Address allocated to you, if Static (Fixed). Other Modems (e.g. Broadband Wireless) Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. None. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you.
9Setup Wizard The Setup Wizard provides brief and basic configuration of this device, you may enter each screen to change the default settings. For more detailed settings, you may refer to the “Configuration via Web” section. 1. View the listed configuration items and click Next to continue. Configuration via Web Operation Mode Select an operation mode and then click Apply to enable the mode you preferred. Operation Mode Access Point When acting as an access point, this device connects all the stations (PC/notebook with wireless
10network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. Gateway Select GW will enter the gateway mode. This means that the wireless connection will be set up from a point-to-point wireless LAN into a point-to-multipoint WAN. Internet Settings WAN (Wide Area Network) Settings WAN Connection Type Select the WAN access type (Static Mode (fixed IP), DHCP (Auto Config), PPPoE (ADSL), L2TP and PPTP) from the pull-down menu. Default setting is DHCP (Auto Config) Type.
11Static Mode IP Address Enter the WAN IP address provided by your ISP in this column. Subnet Mask Enter the Subnet Mask in this column. Default Gateway Enter the default gateway IP provided by your ISP in this column. Primary and Secondary DNS Server The DNS should be set to the address provided by your ISP. Clone PC’s MAC Address Check to enable this function. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Clone IP Address Shows the IP address of the device from the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. DHCP Mode Primary and Secondary DNS The DNS should be set to the address provided by your ISP.
12Server Clone PC’s MAC Address Check to enable this function. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Clone IP Address Shows the IP address of the device from the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. PPPoE Mode User Name Maximum input is 20 alphanumeric characters (case sensitive). Password Maximum input is 20 alphanumeric characters (case sensitive). MTU (Maximum Transmission Unit) Click the pull-down menu to select the most appropriate MTU (Maximum Transmission Unit, namely the maximum packet size, the default value is 1492) for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is entered, you may not be able to open certain web sites. Authentication Type Select PAP, CHAP, MSCHAP-v1, MSCHAP-v2 or Auto form the pull-down menu. MPPE Encryption Level When the authentication type has been set to be MSCHAP-v1, MSCHAP-v2 or Auto, here can select None, 40 bits, 56bits, 128bits or Auto form the pull-down menu. PPPoE IP Address Mode Select Dynamic or Static for the pull-down menu. Physical IP Address Mode Select Dynamic or Static for the pull-down menu. DNS mode Select from the pull-down meun for Static or Dynamic DNS mode.
13Clone PC’s MAC Address Check to enable this function. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Clone IP Address Shows the IP address of the device from the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. L2TP Mode Server Information Select IP address or URL address form the pull-down menu. L2TP Server IP Address Enter the L2TP Server IP Address in this column. L2TP Server URL Address Enter the L2TP Server URL Address in this column. User Name Maximum input is 20 alphanumeric characters (case sensitive). Password Maximum input is 20 alphanumeric characters (case sensitive). MTU (Maximum Transmission Unit) Click the pull-down menu to select the most appropriate MTU (Maximum Transmission Unit, namely the maximum packet size, the default value is 1400) for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is entered, you may not be able to open certain web sites. Authentication Type Select PAP, CHAP, MSCHAP-v1, MSCHAP-v2 or Auto form the pull-down menu.
14MPPE Encryption Level When the authentication type has been set to be MSCHAP-v1, MSCHAP-v2 or Auto, here can select None, 40 bits, 56bits, 128bits or Auto form the pull-down menu. L2TP IP Address Mode Select Dynamic or Static for the pull-down menu. Physical IP Address Mode Select Dynamic or Static for the pull-down menu. DNS mode Select from the pull-down meun for Static or Dynamic DNS mode. Clone PC’s MAC Address Check to enable this function. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Clone IP Address Shows the IP address of the device from the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. PPTP Mode Server Information Select IP address or URL address form the pull-down menu. PPTP Server IP Address Enter the PPTP Server IP Address in this column. PPTP Server URL Address Enter the PPTP Server URL Address in this column. User Name Maximum input is 20 alphanumeric characters (case sensitive). Password Maximum input is 20 alphanumeric characters (case sensitive).
15MTU (Maximum Transmission Unit) Click the pull-down menu to select the most appropriate MTU (Maximum Transmission Unit, namely the maximum packet size, the default value is 1400) for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is entered, you may not be able to open certain web sites. Authentication Type Select PAP, CHAP, MSCHAP-v1, MSCHAP-v2 or Auto form the pull-down menu. MPPE Encryption Level When the authentication type has been set to be MSCHAP-v1, MSCHAP-v2 or Auto, here can select None, 40 bits, 56bits, 128bits or Auto form the pull-down menu. PPTP IP Address Mode Select Dynamic or Static for the pull-down menu. Physical IP Address Mode Select Dynamic or Static for the pull-down menu. DNS mode Select from the pull-down meun for Static or Dynamic DNS mode. Clone PC’s MAC Address Check to enable this function. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Clone IP Address Shows the IP address of the device from the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. LAN (Local Area Network) Settings
16LAN Interface Setup IP Address Shows the IP address of the router. Subnet Mask The subnet mask of the router. DHCP Type Disable: Select to disable this Router to distribute IP addresses. Server: Select to enable this Router to distribute IP Addresses (DHCP Server). And the following field will be activated for you to enter the starting IP Address. DHCP Start IP The starting address of this local IP network address pool. DHCP End IP The ending address of this local IP network address pool. DHCP Subnet Mask Shows the DHCP subnet mask. DHCP Lease Time Default settings are 86400 seconds. IGMP Proxy Select Disable or Enable from the pull-down menu. Apply Click to save and apply the current settings. Refresh Click to get the latest information. DHCP Clients DHCP Clients MAC Address Shows the client MAC address information. IP Address Shows the client IP address information. Expires in Shows the expired time of the client. Wireless Settings
17Basic Wireless Network Radio On/Off Click Radio OFF button to turn off the radio. Network Mode Select 11 b/g mixed mode, 11b only, 11g only or 11 b/g/n mixed mode from the pull-down menu. Default is 11 b/g/n mixed mode. Network Name(SSID) A SSID is referred to a network name because essentially it is a name that identifies a wireless network.
18Multiple SSID 1~6 A multiple SSID is referred to a network name because essentially it is a name that identifies a wireless network. Broadcast Network Name(SSID) Enable: This wireless AP will broadcast its SSID to stations. Disable: This wireless AP will not broadcast its SSID to stations. If stations want to connect to this wireless AP, this AP’s SSID should be known in advance to make a connection. BSSID Shows the MAC address of the router. Frequency (Channel) Select 1~11 or Auto Select from the pull-down menu. Wireless Distribution System(WDS) WDS Mode Select the mode from the pull-down menu, Disable, Lazy Mode, Bridge Mode or Repeater Mode. HT Physical Mode Operating Mode Select Mixed Mode or Green Field. Default setting is Mixed Mode. Channel Band Width Select 20 or 20/40, default setting is 20/40. Guard Interval Select Long or Auto, default setting is Auto. MCS Default setting is Auto. Or select form the pull-down menu 0~15, 32 or Auto. Reverse Direction Grant(RDG) Select Disable or Enable this function, default setting is Enable. Extension Channel You can select 2457MHz (Channel 10) or 2417MHz (Channel 2) form the pull-down menu. Aggregation MSDU (A-MSDU) Select Disable or Enable, default setting is Disable. Auto Block ACK Select Disable or Enable, default setting is Enable. Decline BA Request Select Disable or Enable, default setting is Disable. Other HT TxStream Select 1 or 2 form the pull-down menu. HT RxStream Select 1 or 2 form the pull-down menu. Apply Click to save and apply the current settings. Cancel Click to discard the current settings.
19Advanced Advanced Wireless BG Protection Mode Select Auto, On or Off from the pull-down menu. Basic Data Rates By default, the unit adaptively selects the highest possible rate for transmission. Select the basic rates to be used among the following options: 1-2Mbps, Default (1-2-5.5-11Mbps), or All(1-2-5,5-6-11-12-24Mbps) Beacon Interval Beacon Interval is the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon. Range 20-999, default 100. Data Beacon Rate (DTIM) (range 1 - 255, default 1) Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node”problem is an issue, please
20specify the packet size. The RTS mechanism will be activated if the data size exceeds the value you set.. The default value is 2347. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Short Preamble Select Disable or Enable this function, default setting is Disable. A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. Short Slot Select Disable or Enable this function, default setting is Enable. Tx Burst Select Disable or Enable this function, default setting is Enable. Pkt_Aggregate Select Disable or Enable this function, default setting is Enable. Wi-Fi Multi Media WMM Capable Select Disable or Enable this function, default setting is Enable. APSD Capable Select Disable or Enable this function, default setting is Disable. WMM Parameters Click the WMM Configuration button to go further settings. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. Security Select SSID SSID choice Select the SSID form the pull-down menu for security settings. Security Mode There are eleven type of authentication modes including Disable, Open, Shared, WEP Auto, WPA, WPA-PSK, WPA2, WPA2-PSK, WPA-PSK/WPA2-PSK, WPA1/WPA2 and 802.1X. • Open: If your wireless router is using "Open” authentication, then the
21wireless adapter will need to be set to the same authentication type. • Shared: Shared key is when both the sender and the recipient share a secret key. • WPA, WPA-PSK, WPA2, WPA2-PSK, WPA-PSK/WPA2-PSK, and WPA1/WPA2: WPA-PSK offers two encryption methods, TKIP and AES. Select the type of algorithm, TKIP or AES and then enter a WPA Shared Key of 8~64 characters in the WPA Pre-shared Key field. Encryption Type: For Open and Shared authentication mode, the selection of encryption type are None and WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK authentication mode, the encryption type supports both TKIP and AES. WPA Pre-shared Key: This is the shared secret between AP and STA. For WPA-PSK and WPA2-PSK authentication mode, this field must be filled with character longer than 8 and less than 64 lengths. WEP Key: Only valid when using WEP encryption algorithm. The key must match with the AP’s key. There are several formats to enter the keys. • Hexadecimal (128bits): 26 Hex characters (0~9, a~f). • ASCII (128bits): 13 ASCII characters. WPA Algorithms Select TKIP, AES or TKIP/AES for the WPA Algorithms. Enable Pre-Authentication The two most important features beyond WPA to become standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency. RADIUS Server RADIUS is an authentication, authorization and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The server is a server that has access to a user database with authentication information. IP Address Enter the RADIUS Server’s IP Address provided by your ISP. Port Enter the RADIUS Server’s port number provided by your ISP. The default is 1812. Shared Secret Enter the password that the router shares with the RADIUS Server. Session Timeout Enter the number of seconds that will elapse before the group key change automatically. Idle Timeout It represents that the router will idle after few seconds. The time must be set between 60~3600 seconds. Apply Click to save and apply the current settings. Cancel Click to discard the current settings.
22WPS WPS Configuration WPS Select Enable or Disable from the pull-down menu. Apply Click to save and apply the current settings. WPS Summary Here shows the WPS function status. Reset OOB Click the button to reset the settings. WPS Process WPS mode Select PCB or PIN WPS mode. PIN Enter the PIN code form the registrar or enrollee. Apply Click to save and apply the current settings. WPS Status Here shows the current status of the WPS function.
23 Station List Here shows the information of stations that connected with the AP. Firewall MAC Filtering MAC Filtering Settings MAC Filtering Select Disable, enable –Rules for DROP, or enable –Rules for ACCEPT form the pull-down menu. MAC Address Enter the client MAC address. Comment You may key in a description for the MAC address. Apply Click to save and apply the current settings. Reset Press to discard the current settings. Current MAC filtering rules Here shows the information of the MAC filtering clients. Delete Selected Select the unwanted MAC addresses and then click the Delete Selected button to eliminate them.
24Delete All Click to delete all the MAC addresses in the table. Reset Click to clear the current settings. Access Control Basic Settings Access Control Select Disable or Enable from the pull-down menu. Default Policy -- The packet that don't match with any rules would be: Select Accepted or Dropped from the pull-down menu. Apply Click to save and apply the current settings. Reset Press to discard the current settings. Access Control Settings
25Source IP Address Enter the client IP address. Dest IP Address Enter the destined IP address. Protocol Select the protocol (TCP, UDP or TCP&UDP) used to the remote system or service. Action Select Drop or Accept from the pull-down menu. Comment You may key in a description for the local IP address Apply Click to save and apply the current settings. Reset Press to discard the current settings. Current Access Control rules Here shows the information of the Access Control clients. Delete Selected Select the unwanted IP addresses and then click the Delete Selected button to eliminate them. Delete All Click to delete all the IP addresses in the table. Reset Click to clear the current settings. URL Filtering URL Filter Settings URL Filtering Select Disable or Enable from the pull-down menu. URL String You can block websites with specific URL addresses. Comment You may key in a description for the URL address. Apply Click to save and apply the current settings. Reset Press to discard the current settings. Current URL filtering rules Shows the current URL address status.
26Delete Selected Select the unwanted URL addresses and then click the Delete Selected button to eliminate them. Delete All Click to delete all the URL addresses in the table. Reset Click to clear the current settings. Port Trigger Port Trigger Settings Port Trigger Settings Select Disable or Enable from the pull-down menu. Incoming Protocol Select the protocol (TCP, UDP or TCP&UDP) used to the remote system or service. Incoming Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Trigger Protocol Select the protocol (TCP, UDP or TCP&UDP) used to the remote system or service. Trigger Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Comment You may key in a description for the port trigger. Current Port Shows the current Port Trigger status.
27Trigger list Delete Selected Select the unwanted URL addresses and then click the Delete Selected button to eliminate them. Delete All Click to delete all the URL addresses in the table. Reset Click to clear the current settings. Virtual Servers Virtual Server Settings Virtual Server Settings Select Enable or Disable from the pull-down menu. IP Address Enter the local server’s IP address. Port Range For TCP and UDP services enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Protocol Select the protocol (TCP, UDP or TCP&UDP) used to the remote system or service. Comment You may key in a description for the IP address. Apply Click to save and apply the current settings. Reset Press to discard the current settings. Delete Selected Select the unwanted IP addresses and then click the Delete Selected button to eliminate them. Delete All Click to delete all the IP addresses in the table. Reset Click to clear the current settings.
28DMZ DMZ Settings DMZ Settings If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet / online game can have two-way connections. Select Enable or Disable from the pull-down menu. DMZ IP Address Enter the IP address of a particular host in your LAN that will receive all the packets originally going to the WAN port/Public IP address above. Note: You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly. Apply Click to save and apply the current settings. Reset Press to discard the current settings. Denial of Service
29Denial of Service Settings Enable DoS Prevention DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests, using so much bandwidth and so many resources that Internet access becomes unavailable. The Wireless Router incorporates protection against DoS attacks. This screen allows you to configure DoS protection. Check the box to enable the DoS settings. Select All Click to select all DoS preventions. Clear All Click to uncheck all DoS preventions. Apply Click to enable selected DoS preventions. Administration User/ Password Administrator Settings Account Enter the user name for managing this device. Maximum Input is 16 alphanumeric characters. Password Enter the password for managing this device.. Apply Click to save and apply the current settings. Cancel Click to discard the current settings.
30Time Zone Setting Time Zone Management Current Time Here shows the current time information. Enable NTP Client Check the box to enable below time zone settings. Time Zone Select Select the preferred time zone from the pull-down menu. NTP Servers Auto Selection: Select Auto Selection to select the server automatically. Manual IP: Enter an IP address of a specific server. Daylight Saving Check the box to enable this function, select start and end date from the pull-down menu. Save Click to save the current settings. Refresh Click to renew the current settings. Cancel Click to discard the current settings.
31System Log System Log Management Enable Check the box to enable this function. Apply Changes Click this button to save the settings. Refresh Click to renew the current log message. Clear Click to remove current log message. DDNS DDNS Settings Dynamic DNS Provider • Select the desired DDNS Service Provider None, Dyndns.org, freedns.afraid.org, www.zoneedit.com, and www.no-ip.com from the pull-down list.
32• Details of your DDNS account (Name, password, Domain name) must then be entered and saved on this screen. • This device will then automatically ensure that your current IP Address is recorded by the DDNS Service Provider. • From the Internet, users will now be able to connect to your Virtual Servers (or DMZ PC) using your Domain name. Account Enter the user name for managing this device. Maximum Input is 16 alphanumeric characters. Password Enter the password for managing this device.. DDNS Apply for a Domain Name, and ensure it is allocated to you. Result The result of the update DNS result will show here. Apply Click to save and apply the current settings. Cancel Click to discard the current settings. Refresh Click to refresh the settings. Upload Firmware Update Firmware Location Click the Browse button, find and open the firmware file (the browser will display to correct file path). Apply Click the Apply button to perform. Reset Click Reset to restore to default values.
33Settings Management Export Settings Export Button Click the Export button to export the device settings. Import Settings Settings file location Click the Browse button, find and open the file that has been saved before. (The browser will display to correct file path). Import Click the Import button to import the device settings. Cancel Click to discard the current settings. Load Factory Defaults Load Default Button Click to this button to set the device back to factory default settings.
34 Statistics This screen displays the transmission and reception statistics on your current networks.
35 Chapter 4: PC Configuration Overview For each PC, the following may need to be configured: • TCP/IP network settings • Internet Access configuration • Wireless configuration Windows Clients • This section describes how to configure Windows clients for Internet access via the Wireless Router. • The first step is to check the PC's TCP/IP settings. • The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that the TCP/IP protocol be installed and configured on each PC. TCP/IP Settings - Overview If using default Wireless Router settings, and default Windows TCP/IP settings, no changes need to be made. • By default, the Wireless Router will act as a DHCP Server, automatically providing a suitable IP Address (and related information) to each PC when the PC boots. • For all non-Server versions of Windows, the default TCP/IP setting is to act as a DHCP client. If using a Fixed (specified) IP address, the following changes are required: • The Gateway must be set to the IP address of the Wireless Router. • The DNS should be set to the address provided by your ISP.
36Checking TCP/IP Settings - Windows 2000 1. Select Control Panel - Network and Dial-up Connection. 2. Right - click the Local Area Connection icon and select Properties. You should see a screen like the following: 3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct, as described below.
37Using DHCP • To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP Address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • Enter the Wireless Router's IP address in the Default gateway field and click OK. (Your LAN administrator can advise you of the IP Address they assigned to the Wireless Router.) • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK. Checking TCP/IP Settings - Windows XP 1. Select Control Panel - Network Connection. 2. Right click the Local Area Connection and choose Properties. You should see a screen like the following: 3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following.
38 5. Ensure your TCP/IP settings are correct. Using DHCP • To use DHCP, select Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP Address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • In the Default gateway field, enter the Wireless Router's IP address and click OK. Your LAN administrator can advise you of the IP Address they assigned to the Wireless Router. • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK. Internet Access To configure your PCs to use the Wireless Router for Internet access: • Ensure that the DSL modem, Cable modem, or other permanent connection is functional. • Use the following procedure to configure your Browser to access the Internet via the LAN, rather than by a Dial-up connection.
39For Windows 2000 1. Select Start Menu - Settings - Control Panel - Internet Options. 2. Select the Connection tab, and click the Setup button. 3. Select "I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)" and click Next. 4. Select "I connect through a local area network (LAN)" and click Next. 5. Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked. 6. Check the "No" option when prompted "Do you want to set up an Internet mail account now?" 7. Click Finish to close the Internet Connection Wizard. Setup is now completed. For Windows XP 1. Select Start Menu - Control Panel - Network and Internet Connections. 2. Select Set up or change your Internet Connection. 3. Select the Connection tab, and click the Setup button. 4. Cancel the pop-up "Location Information" screen. 5. Click Next on the "New Connection Wizard" screen. 6. Select "Connect to the Internet" and click Next. 7. Select "Set up my connection manually" and click Next. 8. Check "Connect using a broadband connection that is always on" and click Next. 9. Click Finish to close the New Connection Wizard. Setup is now completed. Accessing AOL To access AOL (America On Line) through the Wireless Router, the AOL for Windows software must be configured to use TCP/IP network access, rather than a dial-up connection. The configuration process is as follows: 1. Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or later. This procedure will not work with earlier versions. 2. Click the Setup button. 3. Select Create Location, and change the location name from "New Locality" to "Wireless Router." 4. Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number blank.) 5. Click Save, then OK. Configuration is now complete. 6. Before clicking "Sign On", always ensure that you are using the "Wireless Router" location.
40Macintosh Clients From your Macintosh, you can access the Internet via the Wireless Router. The procedure is as follows. 1. Open the TCP/IP Control Panel. 2. Select Ethernet from the Connect via pop-up menu. 3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank. 4. Close the TCP/IP panel, saving your settings. Note: If using manually assigned IP addresses instead of DHCP, the required changes are: • Set the Router Address field to the Wireless Router's IP Address. • Ensure your DNS settings are correct. Linux Clients To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router as the "Gateway". Ensure you are logged in as "root" before attempting any changes. Fixed IP Address By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the following changes to your configuration. • Set your "Default Gateway" to the IP Address of the Wireless Router. • Ensure your DNS (Name server) settings are correct. To act as a DHCP Client (Recommended) The procedure below may vary according to your version of Linux and X -windows shell. 1. Start your X Windows client. 2. Select Control Panel - Network 3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0". 4. Click the Edit button, set the "protocol" to "DHCP", and save this data. 5. To apply your changes: • Use the "Deactivate" and "Activate" buttons, if available. • OR, restart your system. Other Unix Systems To access the Internet via the Wireless Router: • Ensure the "Gateway" field for your network card is set to the IP Address of the Wireless Router. • Ensure your DNS (Name Server) settings are correct.
41Wireless Station Configuration • This section applies to all Wireless stations wishing to use the Wireless Router's Access Point, regardless of the operating system that is used on the client. • To use the Wireless Station with Wireless Router, each Wireless Station must have compatible settings, as follows: Mode The mode must be set to Infrastructure. SSID (ESSID) This must match the value used on the Wireless Router. The default value is Untitled. Note! The SSID is case sensitive. WEP By default, the security setting on the Wireless Router is Disabled. • If security setting remains disabled on the Wireless Router, all stations must have it disabled. • If security setting is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. WPA WPA2 (AES) WPA2 Mixed WPA (TKIP/AES)/ WPA2 (AES)/ WPA2 Mixed: If one of these securities is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well. Note: By default, the Wireless Router will allow both 802.11b and 802.11g connections.
Appendix A: Troubleshooting Overview This chapter covers some common problems that may be encountered while using the Wireless Router and some possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the Wireless Router to configure it. Solution 1: Check the following: • The Wireless Router is properly installed, LAN connections are OK, and it is powered ON. • Ensure that your PC and the Wireless Router are on the same network segment. (If you don't have a router, this must be the case.) • If your PC is set to "Obtain an IP Address automatically" (DHCP client), restart it. • If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address within the range 10.10.10.1 to 10.10.10.253 and thus compatible with the Wireless Router's default IP Address of 10.10.10.254. Also, the Network Mask should be set to 255.255.255.0 to match the Wireless Router. In Windows, you can check these settings by using Control Panel-Network to check the Properties for the TCP/IP protocol. Internet Access Problem 1: When I enter a URL or IP address I get a time out error. Solution 1: A number of things could be causing this. Try the following troubleshooting steps. • Check if other PCs work. If they do, ensure that your PCs IP settings are correct. If using a Fixed (Static) IP Address, check the Network Mask, Default gateway and DNS as well as the IP Address. • If the PCs are configured correctly, but still not working, check the Wireless Router. Ensure that it is connected and ON. Connect to it and check its settings. (If you can't connect to it, check the LAN and power connections.) • If the Wireless Router is configured correctly, check your Internet connection (DSL/Cable modem etc) to see that it is working correctly. Problem 2: Some applications do not run properly when using the Wireless Router. Solution 2: The Wireless Router processes the data passing through it, so it is not transparent. Use the Special Applications feature to allow the use of Internet applications, which do not function correctly. If this does solve the problem you can use the DMZ function. This should work with almost every application, but: • It is a security risk, since the firewall is disabled. A
43• Only one (1) PC can use this feature. Wireless Access Problem 1: My PC can't locate the Wireless Router. Solution 1: Check the following: • Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode.) • The SSID on your PC and the Wireless Router are the same. Remember that the SSID is case-sensitive. So, for example "Workgroup" does NOT match "workgroup". • Both your PC and the Wireless Router must have the same setting for security. The default setting for the Wireless Router is disabled, so your wireless station should also have security setting disabled. • If security setting is enabled on the Wireless Router, your PC must have it enabled, and the password or key must match. • If the Wireless Router's Wireless screen is set to Allow LAN access to selected Wireless Stations only, then each of your Wireless stations must have been selected, or access will be blocked. • To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Router. Remember that the connection range can be as little as 100 feet in poor environments. Problem 2: Wireless connection speed is very slow. Solution 2: The wireless system will connect at the highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with the following: • Wireless Router location. Try adjusting the location and orientation of the Wireless Router. • Wireless Channel. If interference is the problem, changing to another channel may show a marked improvement. • Radio Interference. Other devices may be causing interference. You can experiment by switching other devices Off, and see if this helps. Any "noisy" devices should be shielded or relocated. • RF Shielding. Your environment may tend to block transmission between the wireless stations. This will mean high access speed is only possible when close to the Wireless Router.
Appendix B: About Wireless LANs BSS BSS A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a Basic Service Set (BSS). Using the same SSID is essential. Devices with different SSIDs are unable to communicate with each other. Channels The Wireless Channel sets the radio frequency used for communication. • Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. In the USA and Canada, 11 channel are available. If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference. • In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an Access Point. If more than one Access Point can be used, the one with the strongest signal is used. (This can only happen within an ESS.) Security Authentication methods include Disable, Open, Shared, WEP Auto, WPA, WPA-PSK, WPA2, WPA2-PSK, WPA-PSK/WPA2-PSK, WPA1/WPA2 and 802.1X. Once you choose your authentication, you then need to select the Data Encryption methods which may includes WEP Key, Pass Phrase and Radius Server settings. Encryption Enabling WEP can protect your data from eavesdroppers. There are two levels of WEP Encryption: 64 bits and 128 bits. 64 bits WEP encryption requires enter 10 Hex characters as a “secret key”, whereas 128 bits WEP requires users to enter 26 Hex characters as “secret key”. PASS PHRASE is applicable only when you select to use WPA-PSK authentication. You will need to enter an 8~63 characters password to kick off the encryption process, which will generate four WEP keys automatically. RADIUS setup is used to set up additional parameters for authorizing wireless clients through RADIUS server. The RADIUS setup is required when you select to use Open System with 802.1x or WPA/WPA2 authentication. Open, Shared, WEP auto With Shared Key or Open System, the Wireless Router can automatically change its authentication method to Shared Key or Open System depending on its client’s setting. WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is impossible to prevent snoopers from receiving any data that is transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless unless the receiver can decrypt it. If WEP is used, the Wireless Stations and the Access Point must have the same settings for each of the following: B
45 WEP Off, 64 Bit, 128 Bit. Key For 64 Bit encryption, the Key value must match. For 128 Bit encryption, the Key value must match. WEP Authentication Open System or Shared Key. WPA/WPA2 WPA/WPA2 (Wi-Fi Protected Access) is more secure than WEP. It uses a “Shared Key” which allows the encryption keys to be regenerated at a specified interval. There are four encryption options: TKIP, AES, TKIP-AES and additional setup for RADIUS is required in this method. WPA-PSK/WPA2-PSK WPA/WPA2 (Wi-Fi Protected Access using Pre-Shared Key) is recommended for users who are not using a RADIUS server in a home environment and all their clients support WPA/WPA2. This method provides a better security. Encryption WEP Key 1~4 Passphrase TKIP AES NOT REQUIRED 8-63 characters 802.1x With 802.1x authentication, a wireless PC can join any network and receive any messages that are not encrypted, however, additional setup for RADIUS to issue the WEP key dynamically will be required. Wireless LAN Configuration To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access Point must use the same settings, as follows: Mode On client Wireless Stations, the mode must be set to "Infrastructure." (The Access Point is always in "Infrastructure" mode.) SSID (ESSID) Wireless Stations should use the same SSID (ESSID) as the Access Point they wish to connect to, but the SSID can not set to be null (blank). WEP The Wireless Stations and the Access Point must use the same settings for WEP (Off, 64 Bit, 128 Bit). WEP Key: If WEP is enabled, the Key must be the same on the Wireless Stations and the Access Point. WEP Authentication: If WEP is enabled, all Wireless Stations must use the same setting as the Access Point (either "Open System" or "Shared Key"). WPA WPA2 (AES) WPA2 Mixed WPA (TKIP/AES)/ WPA2 (AES)/ WPA2 Mixed: If one of these securities is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well.
46Regulatory Approvals FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CE Statement: Hereby, AboCom, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Driective 1999/5/EC. CE Standards This product complies with the 99/5/EEC directives, including the following safety and EMC standards:
47• EN300328-2 • EN301489-1/-17 • EN60950 CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Navigation menu