Abocom Systems WUG2650-4 802.11b/g USB WLAN Adapter User Manual WUG2650 2654MNL

Download:
Mirror Download [FCC.gov]
Document ID	455174
Application ID	T80JbPNDhyC4C3ktbQHHXQ==
Document Description	Manual revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.9kB (636286 bits)
Date Submitted	2004-07-30 00:00:00
Date Available	2004-07-30 00:00:00
Creation Date	2004-07-28 15:06:59
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	2004-07-30 15:39:18
Document Title	WUG2650+2654MNL.doc
Document Creator	WUG2650+2654MNL - Microsoft Word
Document Author:	claire

802.11g Wireless LAN
USB Adapter
User Manual
REGULATORY STATEMENTS
FCC Certification
The United States Federal Communication Commission (FCC) and the
Canadian Department of Communications have established certain rules
governing the use of electronic equipment.
Part15, Class B
This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interface, and
2) This device must accept any interface received, including interface that may
cause undesired operation. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
w Reorient or relocate the receiving antenna.
w Increase the distance between the equipment and receiver.
w Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
CAUTION:
Please note that as this device can be used within 2.5cm of the body.
Channel
The Wireless Channel sets the radio frequency used for communication.
•Access Points use a fixed Channel. You can select the Channel used.
This allows you tochoose a Channel which provides the least interference
and best performance. In the USA and Canada, 11 channel are available.
If using multiple Access Points, it is better if adjacent Access Points use
different Channels to reduce interference.
• In "Infrastructure" mode, Wireless Stations normally scan all Channels,
looking for an Access Point. If more than one Access Point can be used,
the one with the strongest signal is used. (This can only happen within an
ESS.)
• If using "Ad-hoc" mode (no Access Point), all Wireless stations should
be set to use the same Channel. However, most Wireless stations will
still scan all Channels to see if there is an existing "Ad-hoc" group they
can join.
Please be careful to use this product to avoid being affected by the
electromagnetic wave.
SAR standard value: 1.6 W/ Kg
EUT testing value: 0.575 W/ Kg
Table of Contents
INTRODUCTION ....................................................................................................1
FEATURES..............................................................................................................1
LED INDICATORS...................................................................................................
WIRELESS BASICS ..................................................................................................
W IRELESS NETWORK OPTIONS............................................................................
INSTALLATION......................................................................................................2
INSTALL THE DRIVER & UTILITY ......................................................................2
INSTALL THE DEVICE...........................................................................................4
NETWORK CONNECTION ..................................................................................9
IN W INDOWS 98SE/ME ......................................................................................9
IN W INDOWS 2000/XP ......................................................................................13
IP A DDRESS ........................................................................................................16
USE CONFIGURATION UTILITY.........................................................................
A CCESS THE CONFIGURATION UTILITY..............................................................
General.......................................................................................................
Profiles .......................................................................................................
Current Statistics......................................................................................
About..........................................................................................................
BASIC OPERATION.................................................................................................
SETTING UP A WIRELESS INFRASTRUCTURE NETWORK
SETTING UP A WIRELESS A D-HOC (PEER-T O-PEER) NETWORK .....................
UNINSTALLATION..................................................................................................
UNINSTALL THE UTILITY......................................................................................
UNINSTALL THE DRIVER.......................................................................................
INTRODUCTION
The 802.11g Wireless LAN USB Adapter is designed for a USB type A
port of a laptop or desktop computer for creating a wireless workstation.
This 802.11g Wireless LAN USB Adapter is USB 2.0 compliant which
connects to any available USB port on a notebook or desktop computer.
The 802.11g Wireless LAN USB Adapter complies with IEEE 802.11g
standard that offers a data rate up to 54Mbps in a wireless LAN
environment. It is a high-speed wireless network card that plugs into your
notebook or desktop PC and accesses to the LAN or peer-to-peer
networking easily without wires or cables. Whether you’re at your desk or
in the boardroom, it allows you to share printers, files, and other network
resources.
Features
Ø Complies with IEEE 802.11g standard for 2.4GHz Wireless LAN
Ø USB 2.0 compliant
Ø USB Plug & Play
Ø Interoperable with existing network infrastructure
Ø Secure information transmission
Ø Freedom to roam while staying connected
Ø Compatible with specialty wireless products and services
Ø Up to 54 Mbps data rate
Ø Antenna is built in the card with LEDs indication
Ø Low power consumption
Ø Easy to install and configure
Ø Auto-installation and configuration (optional)
-1 -
INSTALLATION
Note: For users who purchased the auto-install model, it is not necessary
to manually install the driver & utility as described below. Just plug the
device to your computer and the program will proceed automatically.
Install the Driver & Utility
1.
Exit all Windows programs. Insert the included CD-ROM into your
computer.
If the CD-ROM fails to run automatically, go to your CD-ROM
drive (e.g. drive D) and double-click on autorun.exe.
2.
When the main screen of the CD-ROM opens, click Install Driver &
Utility to start the installation.
3.
When the Welcome screen appears, click Next to continue.
4.
In License Agreement, click Yes to accept the terms . Then, the
installation will finish automatically.
-2 -
Note for Windows 98SE/ME users
When Windows finish the installation, select “Yes, I want to restart
my computer now.” and then click Finish to reboot your computer.
-3 -
Install the Device
Note: For the auto-install model users, before you plug the Wireless
USB Adapter into your PC’s USB port, please make sure to turn the
switch right to have the program automatically proceed.
Switch right to turn on the auto-installation.
1.
2.
Once the device has been inserted to your computer, Windows will
detect the new hardware.
Refer to the following section according to your operating system for
important notice.
Note for Windows 98SE users:
1.
Before installing the device, make sure you have your original
Windows 98 CD-ROM at hand.
2.
Once the “Please insert the disk labeled ‘Windows 98 Second
Edition CD-ROM, and then click OK” window appears, click
OK.
-4 -
Note for Windows ME users:
After installing the device, the system will finish the process of the
installation automatically.
-5 -
Note for Windows 2000 users:
When the “Digital Signature Not Found” screen appears, click “Yes”
to continue.
Note for Windows XP users:
1. Select Install the software automatically (Recommended) and click
Next.
-6 -
2. Click Continue Anyway.
3. Click Finish to complete the installation.
-7 -
Verify
To verify if the device exists in your computer and is enabled, go to Start
à Settings à Control Panel à Syste m (à Hardware) à Device
Manager. Expand the Network Adapters category. If the USB 2.0
Wireless Network Adapter is listed here, it means that your device is
properly installed and enabled.
-8 -
NETWORK CONNECTION
Once the device driver is well installed, a network setting described in the
following should be also established.
In Windows 98SE/ME
1.
2.
Go to Start à Settings à Control Panel à Network.
Make sure that the following components are installed.
§ USB 2.0 Wireless Network Adapter
§ IPX/SPX-compatible Protocol
§ NetBEUI
§ TCP/IP
-9 -
If any components are missing, click on the Add button to add them in.
All the protocols and clients required and listed above are provided by
Microsoft.
3. After clicking Add, highlight the component you need, click Add.
4.
Highlight Microsoft, and then double click on the item you want to
add. Click OK.
5.
For making your computer visible on the network, enable the File
and Print Sharing.
- 10 -
6.
Click the Identification tab. Make up a name that is unique from the
other computers' names on the network. Type the name of your
workgroup, which should be the same used by all of the other PCs on
the network.
7.
Click the Access Control tab. Make sure that “Share-level access
control” is selected. If connecting to a Netware server, share level
can be set to “User-level access control.”
- 11 -
8.
When finished, restart your computer to activate the new device.
9.
Once the computer has restarted and Windows has booted up, a
Logon window will appear and require you to enter a username and
password. Make up a username and password and click OK. Do not
click the Cancel button, or you won’t be able to log onto the network.
10. Double-click the Network Neighborhood icon on the windows
desktop, and you should see the names of the other PCs on the
network.
- 12 -
In Windows 2000/XP
1.
(In Windows 2000)
Go to Startà Settings à Control Panel à Network and Dial-up
Connections à Local Area Connection à Properties.
(In Windows XP)
Go to Start à Control Panel à Network Connections à Wireless
Network Connection Enabled USB Wireless Network Adapter à
Properties.
- 13 -
2. Make sure that you have all the following components installed.
§ Client for Microsoft Networks
§ File and Printer Sharing for Microsoft Networks
§ Internet Protocol (TCP/IP)
3.
If any components are missing, click on the Install… button to select
the Client/Service/Protocol required. After selecting the component
you need, click Add… to add it in.
- 14 -
4.
5.
For making your computer visible on the network, make sure you
have installed File and Printer Sharing for Microsoft Networks.
When finished, restart your computer to complete the installation.
- 15 -
IP Address
Note: When assigning IP Addresses to the computers on the network,
remember to have the IP address for each computer set on the same
subnet mask. If your Broadband Router use DHCP technology, however, it
won’t be necessary for you to assign Static IP Address for your computer.
To configure a dynamic IP address (i.e.
if your broadband Router has the
DHCP technology), check the Obtain
an IP Address Automatically option.
To configure a fixed IP address (if you
broadband Router is not DHCP supported,
or when you need to assign a static IP
address), check the Use the following IP
address option. Then, enter an IP address
into the empty field, for example, enter
192.168.1.1 in the IP address field, and
255.255.255.0 for the Subnet Mask.
- 16 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:07:28 15:06:59Z
Modify Date                     : 2004:07:30 15:39:18+08:00
Page Count                      : 21
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©
Creation Date                   : 2004:07:28 15:06:59Z
Mod Date                        : 2004:07:30 15:39:18+08:00
Author                          : claire
Creator Tool                    : WUG2650+2654MNL - Microsoft Word
Metadata Date                   : 2004:07:30 15:39:18+08:00
Title                           : WUG2650+2654MNL.doc
Creator                         : claire

EXIF Metadata provided by EXIF.tools