Abocom Wu5205 Users Manual WU5205_MNL_English Plus Vista

WU5205 to the manual 52825e7d-80bc-4f41-8481-8d3c944bffb5

2015-02-05

: Abocom Abocom-Wu5205-Users-Manual-503725 abocom-wu5205-users-manual-503725 abocom pdf

Open the PDF directly: View PDF .
Page Count: 85

Download
Open PDF In Browser	View PDF

802.11 b/g/n
Micro Mini Wireless LAN
USB2.0 Adapter

User’s Manual

Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
z

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.

Country Code Statement
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
To maintain compliance with FCC RF exposure requirements, use only
belt-clips, holsters or similar accessories that do not contain metallic
components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements, and should
be avoided.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

Federal Communication Commission (FCC) Radiation
Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled
exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance
with the measurement methods and procedures specified in OET Bulletin 65
Supplement C. This equipment should be installed and operated with minimum
distance 2.5cm between the radiator & your body.

CE Statement:
Hereby, AboCom, declares that this device is in compliance with the
essential requirement and other relevant provisions of the R&TTE
Driective 1999/5/EC.

Trade Mark: AboCom

Table of Contents
INTRODUCTION ...................................................................................................1
FEATURES ..............................................................................................................1
Windows 2000/XP Installation ...............................................................................2
INSTALL THE SOFTWARE .........................................................................................2
INSTALL THE HARDWARE .......................................................................................5
Windows Vista Installation.....................................................................................6
INSTALL THE SOFTWARE .........................................................................................6
INSTALL THE HARDWARE .......................................................................................8
VERIFICATION ........................................................................................................8
NETWORK CONNECTION .................................................................................9
IP ADDRESS ...........................................................................................................9
UTILITY CONFIGURATION FOR WINDOWS 2000/XP...............................10
STATION MODE ....................................................................................................11
Profile ......................................................................................................11
Network ...................................................................................................20
Link Status...............................................................................................23
Advanced.................................................................................................25
Statistics...................................................................................................27
WMM / QoS ............................................................................................28

WPS.........................................................................................................30
Radio On/Off ...........................................................................................33
About .......................................................................................................34
UTILITY MENU LIST .............................................................................................35
SOFT AP MODE .....................................................................................................36
Config......................................................................................................36
Access Control.........................................................................................39
MAC Table..............................................................................................40
Event Log ................................................................................................41
Statistics...................................................................................................42
About .......................................................................................................43
UTILITY CONFIGURATION FOR WINDOWS VISTA.................................44
STATION MODE ....................................................................................................45
Profile ......................................................................................................45
Network ...................................................................................................53
Link Status...............................................................................................57
Advanced.................................................................................................59
Statistics...................................................................................................60
WMM / QoS ............................................................................................62
WPS.........................................................................................................63
Radio On/Off ...........................................................................................66
About .......................................................................................................67
UTILITY MENU LIST .............................................................................................67

SOFT AP MODE .....................................................................................................68
Config......................................................................................................68
Access Control.........................................................................................71
MAC Table..............................................................................................72
Event Log ................................................................................................73
Statistics...................................................................................................74
About .......................................................................................................75
UNINSTALLATION FOR WINDOWS 2000/XP...............................................76
UNINSTALLATION FOR WINDOWS VISTA .................................................78

INTRODUCTION
The WU5205 is an IEEE802.11b/g/n USB adapter that connects your
notebook to a wireless local area. The WU5205 fully complies with IEEE
802.11n draft 3.0 and IEEE 802.11 b/g standards, delivers reliable,
cost-effective, feature rich wireless connectivity at high throughput from
an extended distance.
The WU5205 is a very small adapter that can connects notebook,
handheld or desktop computer equipped with USB interface for wireless
network applications. It allows you to take full advantage of your
notebook’s mobility with access to real-time information and online
services anytime and anywhere.

Features
¾
¾
¾
¾
¾
¾
¾
¾

1T1R Mode with 150Mbps PHY Rate for both.
Complies with IEEE 802.11n draft 3.0 and IEEE 802.11 b/g standards.
Supports WEP 64/128, WPA, WPA2.
Supports WMM and WMM-PS.
Supports WPS configuration.
Supports USB 2.0/1.1 interface.
Portable and mini-size design.
Compatible with Microsoft Windows Vista, XP, 2000.

-1-

Windows 2000/XP Installation
Install the Software
Caution!
Do not insert the wireless card into your computer until the InstallShield
Wizard finish installing.

1. Exit all Windows programs. Insert the included CD-ROM into your
computer. The CD-ROM will run automatically.
2. When the License Agreement screen appears, please read the
contents and select “I accept the terms of the license agreement
“ then click Next to continue.

-2-

3. Select the check box to choose a Configuration Tool from the listed
two choices.
z

Configuration Tool: Choose to use our configuration utility.

Microsoft Zero Configuration Tool: Choose to use Windows XP’s
built-in Zero Configuration Utility (ZCU).

Click Next to continue.

5. When you are prompted the following message, please click Install
to begin the installation.

-3-

6. When the following screen appears, click Finish to complete the
software installation.

-4-

Install the Hardware
Note: Insert the Wireless USB card when you finished your software
installation.
Insert the USB Adapter into the USB Port of your computer. The system
will automatically detect the new hardware.

-5-

Windows Vista Installation
Install the Software
Do not insert the wireless LAN adapter into your computer until the
procedures in “Driver& Utility Installation” have been performed.

Insert the included CD-ROM into the CD-ROM drive of your
computer.

When the Main Menu screen appears, click “Driver & Utility
Installation” to start the software installation.

When the License Agreement screen appears, please read the
contents and select “I accept the terms of the license agreement
“ then click Next to continue.

-6-

When you are prompted the following message, please click Install
to begin the installation.

When the following screen appears, click Finish to complete the
software installation.

-7-

Verification
To verify if the device exists in your computer and is enabled, go to Start >
Control Panel > System > Hardware > Device Manager. Expand the Network
Adapters category. If the 802.11 USB Wireless LAN Card is listed here, it
means that your device is properly installed and enabled.

-8-

NETWORK CONNECTION
IP Address
Note: When assigning IP Addresses to the computers on the network, remember
to have the IP address for each computer set on the same subnet mask. If your
Broadband Router use DHCP technology, however, it won’t be necessary for you
to assign Static IP Address for your computer.
1. To configure a dynamic IP address (i.e. if your broadband Router has the DHCP
technology), check the Obtain an IP Address Automatically option.
2. To configure a fixed IP address (if you broadband Router is not DHCP
supported, or when you need to assign a static IP address), check the Use the
following IP address option. Then, enter an IP address into the empty field; for
example, enter 192.168.1.1 in the IP address field, and 255.255.255.0 for the
Subnet Mask.

-9-

UTILITY CONFIGURATION FOR
WINDOWS 2000/XP
After the Wireless adapter has been successfully installed, users can use the
included Configuration Utility to set their preference.
Go to StartJ (All) ProgramJ Intelligent WirelessJ Intelligent Wireless
Utility.

You can also open the Configuration Utility by double clicking the icon or right
clicking to select Launch Config Utility.

- 10 -

Station Mode
Notice: Under screen resolution 800 x 600 pixels, click the triangle button at
the right down corner of the utility to expand the information of the station,
the information will not be displayed completely.

Profile
Profile can book keeping your favorite wireless setting among your home, office,
and other public hot-spot. You may save multiple profiles, and activate the correct
one at your preference. The Profile manager enables you to Add, Edit, Delete and
Activate profiles.
Click this button to show the information of Status Section.
Click this button to hide the information of Status Section.

Profile Tab
Profile Name
SSID

You can see a distinctive name of profile in this column.
The default is PROF# (# 1, #2, #3....)
The SSID is the unique name shared among all points in
your wireless network.
- 11 -

Network Type

Shows the network type of the device, including
Infrastructure and Ad-Hoc.

Authentication

Shows the authentication mode.

Encryption

Shows the encryption type.

Use 802.1x

Whether or not use 802.1x feature.

Tx Power

Transmit power, the amount of power used by a radio
transceiver to send the signal out.

Channel

Shows the selected channel that is currently in use.

Power Save
Mode

Choose from CAM (Constantly Awake Mode) or PSM
(Power Saving Mode.)

RTS Threshold

Shows the RTS Threshold of the device.

Fragment
Threshold

Shows the Fragment Threshold of the device.

Add

Click to add a profile from the drop-down screen.
System Configuration tab:

Profile Name: User can enter profile name, or use default
name defined by system. The default is PROF# (# 1, #2,
#3....).
- 12 -

SSID: The SSID is the unique name shared among all
points in your wireless network. The name must be
identical for all devices and points attempting to connect
to the same network. User can use pull-down menu to
select from available APs.
Power Save Mode:
• CAM (Constantly Awake Mode): When this mode is
selected, the power supply will be normally provided
even when there is no throughput.
• PSM (Power Saving Mode): When this mode is
selected, this device will stay in power saving mode
even when there is high volume of throughput.
Network Type: There are two types, Infrastructure and
Ad-hoc modes. Under Ad-hoc mode user can also choose
the preamble type, the available preamble type includes
Auto and Long. In addition to that, the channel field will
be available for setup in Ad-hoc mode.
• The Infrastructure is intended for the connection
between wireless network cards and an Access Point.
With the wireless adapter, you can connect wireless
LAN to a wired global network via an Access Point.
• The Ad-hoc lets you set a small wireless workgroup
easily and quickly. Equipped with the wireless
adapter, you can share files and printers between each
PC and laptop.
Tx Power: Transmit power, the amount of power used by
a radio transceiver to send the signal out. Select the Tx
power percentage from the pull-down list including Auto,
100%, 75%, 50%, 25%, 10% and Lowest.
Preamble: This function will show up when Ad-hoc
network type be selected. A preamble is a signal used in
wireless environment to synchronize the transmitting
timing including Synchronization and Start frame
delimiter. Select from the pull-down menu to change the
- 13 -

Preamble type into Auto or Long.
RTS Threshold: User can adjust the RTS threshold
number by sliding the bar or key in the value directly. The
default value is 2347. RTS/CTS Threshold is a mechanism
implemented to prevent the “Hidden Node” problem. If
the “Hidden Node” problem is an issue, users have to
specify the packet size. The RTS/CTS mechanism will be
activated if the data size exceeds the value you set.
This value should remain at its default setting of 2347.
Should you encounter inconsistent data flow, only minor
modifications of this value are recommended.
Fragment Threshold: User can adjust the Fragment
threshold number by sliding the bar or key in the value
directly. The default value is 2346. The mechanism of
Fragmentation Threshold is used to improve the efficiency
when high traffic flows along in the wireless network. If
your Wireless LAN Adapter often transmits large files in
wireless network, you can enter new Fragment Threshold
value to split the packet. The value can be set from 256
to 2346.
Authentication and Security tab:

Authentication Type: There are several types of
authentication modes including Open, Shared, Leap,
WPA, WPA-PSK, WPA2 and WPA2-PSK.
• Open: If your access point/wireless router is using
"Open” authentication, then the wireless adapter will
- 14 -

need to be set to the same authentication type.
• Shared: Shared key is when both the sender and the
recipient share a secret key.
• LEAP: Light Extensible Authentication Protocol. It is
an EAP authentication type used primarily in Cisco
Aironet WLANs. It encrypts data transmissions using
dynamically generated WEP keys, and supports mutual
authentication (only with CCX mode enabled.)
• WPA/ WPA-PSK/ WPA2/ WPA2-PSK: WPA or
WPA-PSK authentications offer two encryption
methods, TKIP and AES. For WPA-PSK, select the
type of algorithm TKIP or AES and then enter a WPA
Shared Key of 8-64 characters in the WPA Pre-shared
Key field.
Encryption Type: For Open and Shared authentication
mode, the selection of encryption type are None and
WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication mode, the encryption type supports both
TKIP and AES.
WPA Pre-shared Key: This is the shared secret between
AP and STA. For WPA-PSK and WPA2-PSK
authentication mode, this field must be filled with
character longer than 8 and less than 64 lengths.
WEP Key: Only valid when using WEP encryption
algorithm. The key must match with the AP’s key. There
are several formats to enter the keys.
• Hexadecimal (128bits): 26 Hex characters (0~9, a~f).
• ASCII (128bits): 13 ASCII characters.
Show Password: Check this box to show the password
you en02tered.
- 15 -

802.1x Setting: When user use radius server to
authenticate client certificate for WPA authentication
mode (WPA authentication do not support EAP MethodMD5-Challenge).
802.1x tab:

EAP Method:
• PEAP: Protect Extensible Authentication Protocol.
PEAP transport securely authentication data by using
tunnelling between PEAP clients and an authentication
server. PEAP can authenticate wireless LAN clients
using only server-side certificates, thus simplifying the
implementation and administration of a secure
wireless LAN.
•

authentication and can be used to dynamically
generate user-based and session-based WEP keys to
secure subsequent communications between the
WLAN client and the access point.
•

TTLS: Tunnelled Transport Layer Security. This
security method provides for certificate-based, mutual
authentication of the client and network through an
encrypted channel. Unlike EAP-TLS, EAP-TTLS
requires only server-side certificates.

•

EAP-FAST: Flexible Authentication via Secure
Tunnelling. It was developed by Cisco. Instead of
using a certificate, mutual authentication is achieved
by means of a PAC (Protected Access Credential)
which can be managed dynamically by the
authentication server. The PAC can be provisioned
(distributed one time) to the client either manually or
automatically. Manual provisioning is delivery to the
client via disk or a secured network distribution
method. Automatic provisioning is an in-band, over
the air, distribution. For tunnel authentication, only
support "Generic Token Card" authentication now.

•

MD5-Challenge: Message Digest Challenge.
Challenge is an EAP authentication type that provides
base-level EAP support. It provides for only one-way
authentication - there is no mutual authentication of
wireless client and the network. (Only Open and
Shared authentication mode can use this function.)

Tunnel Authentication:
• Protocol: Tunnel protocol, List information including
EAP-MSCHAP v2, EAP-TLS/ Smart Card, and
Generic Token Card.
•

Tunnel Identity: Identity for tunnel.
- 17 -

•

Tunnel Password: Password for tunnel.

Session Resumption: Reconnect the signal while broken
up, to reduce the packet and improve the transmitting
speed. User can click the box to enable or disable this
function.
ID\PASSWORD tab:

ID/ PASSWORD: Identity and password for server.
• Authentication ID / Password: Identity, password
and domain name for server. Only "EAP-FAST" EAP
method and "LEAP" authentication can key in domain
name. Domain name can be keyed in blank space.
• Tunnel ID / Password: Identity and Password for
server.
Show Password: Check this box to show the password
you entered.
OK: Click to save settings and exit this page.
Cancel: Click to call off the settings and exit.
Client Certification tab:

Use Client certificate: Choose to enable server
- 18 -

authentication.
OK: Click to save settings and exit this page.
Cancel: Click to call off the settings and exit.
Server Certification tab:

Use certificate chain: Choose use server that issuer of
certificates.
Allow intimidate certificates: It must be in the server
certificate chain between the server certificate and the
server specified in the certificate issuer must be field.
Server name: Enter an authentication sever root.
Server name must match: Click to enable or disable this
function.
Domain name must end in specified name: Click to
enable or disable this function.
OK: Click to save settings and exit this page.
Cancel: Click call off the settings and exit.
Delete

Click to delete an existing profile.

Edit

Click to edit a profile.

Activate

Click to make a connection between devices.

- 19 -

Network
The Network page displays the information of surrounding APs from last scan
result. The tab lists the information including SSID, Network type, Channel,
Wireless mode, Security-Enabled and Signal.

Network Tab
Sorted by

Indicate that AP list are sorted by SSID, Channel or Signal.

Show dBm

Check the box to show the dBm of the AP list.

SSID

Shows the name of BSS network.

Network Type

Network type in use, Infrastructure for BSS, Ad-Hoc for
IBSS network.

Channel

Shows the currently used channel.

Wireless mode

AP support wireless mode. It may support 802.11b,
802.11g or 802.11n wireless mode.

Encryption

Shows the encryption type currently in use. Valid value
includes WEP, TKIP, AES, Not Use and WPS.

Signal

Shows the receiving signal strength of specified network.

Rescan

Click to refresh the AP list.

Add to Profile

Select an item on the list and then click to add it into the
profile list.
- 20 -

Connect

Select an item on the list and then click to make a
connection.

AP Information
When you double click on the intended AP, you can see AP's detail information
that divides into four parts. They are General, WPS, CCX and 802.11n
information. The introduction is as following:
General

General information contain AP's SSID, MAC address,
Authentication Type, Encryption Type, Channel, Network
Type, Beacon Interval, Signal Strength and Supported
Rates.
Close: Click this button to exit the information screen.
WPS

WPS information contains Authentication Type, Encryption
Type, Config Methods, Device Password ID, Selected
Registrar, State, Version, AP Setup Locked, UUID-E and
RF Bands.
- 21 -

Authentication Type: There are four types of
authentication modes supported by RaConfig. They are
Open, Shared, WPA-PSK and WPA system.
Encryption Type: For Open and Shared authentication
mode, the selection of encryption type are None and WEP.
For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication mode, the encryption type supports both
TKIP and AES.
Config Methods: Correspond to the methods the AP
supports as an Enrollee for adding external Registrars.
Device Password ID: Indicate the method or identifies the
specific password that the selected Registrar intends to use.
Selected Registrar: Indicate if the user has recently
activated a Registrar to add an Enrollee. The values are
"TRUE" and "FALSE".
State: The current configuration state on AP. The values
are "Unconfigured" and "Configured".
Version: WPS specified version.
AP Setup Locked: Indicate if AP has entered a setup
locked state.
UUID-E: The universally unique identifier (UUID) element
generated by the Enrollee. There is a value. It is 16 bytes.
RF Bands: Indicate all RF bands available on the AP. A
dual-band AP must provide it. The values are "2.4GHz".
Close: Click this button to exit the information screen.
CXX

- 22 -

CCX information contains CCKM, Cmic and Ckip
information.
Close: Click this button to exit the information screen.
802.11n

This tab will show up if you select the AP that support 11n
mode. Here shows the connected AP 802.11n related
information.

Link Status
Click the triangle button at the right down corner of the windows to expand the
link status. The link status page displays the detail information of current
connection.
Click this button to show the information of Status Section.
Click this button to hide the information of Status Section.

- 23 -

Link Status Tab
Status

Shows the current connected AP SSID and MAC
address. If there is no connection existing, it will show
Disconnected.

Extra Info

Shows the link status and Tx power percentage.

Channel

Shows the current channel in use.

Authentication

Authentication mode used within the network,
including Unknown, WPA-PSK, WPA2-PSK, WPA
and WPA2.

Encryption

Shows the encryption type currently in use. Valid
value includes WEP, TKIP, AES, and Not Use.
- 24 -

Network Type

Network type in use, Infrastructure for BSS, Ad-Hoc
for IBSS network.

IP Address

Shows the IP address information.

Sub Mask

Shows the Subnet Mask information.

Default Gateway

Shows the default gateway information.

Link Quality

Shows the connection quality based on signal strength
and TX/RX packet error rate.

Signal Strength 1

Shows the Receiving signal strength, you can choose
to display as percentage or dBm format.

Noise Strength

Shows the noise signal strength in the wireless
environment.

Transmit

Shows the current Link Speed and Throughput of the
transmit rate.

Receive

Shows the current Link Speed and Throughput of
receive rate.

Link Speed

Shows the current transmitting rate and receiving rate.

Throughput

Shows the transmitting and receiving speed of data.

Advanced
This Advanced page provides advanced and detailed settings for your wireless
network.

- 25 -

Advanced Tab
Wireless mode

Here supports 2.4G (included 802.11b/g/n) wireless mode.

Enable TX Burst

Check to enable this function. This function enables the
adapter to deliver better throughput during a period of
time, it only takes effect when connecting with the AP
that supports this function.

Enable TCP
Window Size

Check to increase the transmission quality. The large TCP
window size the better performance.

Fast Roaming at
dBm

Check to set the roaming interval, fast to roaming, setup
by transmits power. Default setting is -70dBm.

Show
Authentication
Status Dialog

When you connect AP with authentication, choose
whether show "Authentication Status Dialog" or not.
Authentication Status Dialog displays the process about
802.1x authentications.

Enable CCX
(Cisco Compatible
extensions)

Check to enable the CCX function.
• Turn on CCKM.
• Enable Radio Measurements: Check to enable the
Radio measurement function.
• Non-Serving Measurements limit: User can set channel
measurement every 0~2000 milliseconds. Default is set
to 250 milliseconds.
- 26 -

Apply

Click to apply above settings.

Statistics
The Statistics screen displays the statistics on your current network settings.

Transmit
Frames Transmitted Successfully Shows information of frames successfully
sent.
Frames Retransmitted
Successfully

Shows information of frames successfully
sent with one or more reties.

Frames Fail To Receive ACK
After All Retries

Shows information of frames failed
transmit after hitting retry limit.

RTS Frames Successfully Receive Shows information of successfully receive
CTS after sending RTS frame
CTS
RTS Frames Fail To Receive
CTS

Shows information of failed to receive CTS
after sending RTS.

Reset Counter

Click this button to reset counters to zero.

- 27 -

Receive Statistics
Frames Received Successfully

Shows information of frames Received
Successfully.

Frames Received With CRC
Error

Shows information of frames received with
CRC error.

Frames Dropped Due To
Out-of-Resource

Shows information of frames dropped due
to resource issue.

Duplicate Frames Received

Shows information of frames received
more than twice.

Reset Counter

Click this button to reset counters to zero.

WMM / QoS
The WMM page shows the Wi-Fi Multi-Media power save function and Direct
Link Setup that ensure your wireless network quality.

- 28 -

WMM Enable

Check the box to enable Wi-Fi Multi-Media
function that is meant to improve audio, video
and voice applications transmitted over Wi-Fi.

WMM- Power Save Enable

Select which ACs you want to enable the power
saving mode.
AC_BK (Access Category Background)
AC_BE (Access Category Best Effort)
AC_VI (Access Category Video)
AC_VO (Access Category Voice)

Direct Link Setup Enable

Check the box to enable Direct Link Setup.

MAC Address

The setting of DLS( Direct Link Setup) indicates
as follow :
Fill in the blanks of Direct Link with MAC
Address of STA, and the STA must conform to
two conditions:
• Connecting with the same AP that supports
DLS feature.
• DLS enabled.

Timeout Value

Timeout Value represents that it disconnect
automatically after few seconds. The value is
integer that must be between 0~65535. It
represents that it always connects if the value is
zero. Default value of Timeout Value is 60
seconds.
- 29 -

Apply

Click this button to apply the settings.

Tear Down

Select a direct link STA, then click "Tear Down"
button to disconnect the STA.

WPS
The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to
simplify the security setup and management of Wi-Fi networks. The STA as an
Enrollee or external Registrar supports the configuration setup using PIN
(Personal Identification Number) configuration method or PBC (Push Button
Configuration) method through an internal or external Registrar.

WPS AP List

Display the information of surrounding APs with WPS IE
from last scan result. List information included SSID,
BSSID, Channel, ID (Device Password ID),
Security-Enabled.

Rescan

Issue a rescan command to wireless NIC to update
information on surrounding wireless network.

Information

Display the information about WPS IE on the selected
- 30 -

network. List information included Authentication Type,
Encryption Type, Config Methods, Device Password ID,
Selected Registrar, State, Version, AP Setup Locked,
UUID-E and RF Bands.
PIN Code

8-digit numbers. It is required to enter PIN Code into
Registrar when using PIN method. When STA is
Enrollee, you can use "Renew" button to re-generate new
PIN Code.

Config Mode

Select from the pull-down menu to decide the station
role-playing as an Enrollee or an external Registrar.

Detail

Click the Detail button to show the information about
Security and Key in the credential.

If you select the AP that listed in the WPS Profile List
field, you can click the Detail button to see more AP
information.
SSID: Shows the connected AP network name.
- 31 -

BSSID: The MAC address of the connected AP. Fixed
and cannot be changed.
Authentication Type: The authentication type support
Open, WPA-PSK and WPA2-PSK.
Encryption Type: For Open authentication mode, the
selection of encryption type are NONE and WEP. For
WPA-PSK and WPA2-PSK authentication mode, the
encryption type supports both TKIP and AES.
Key Length: Only valid when using Open authentication
mode and WEP encryption. There are key lengths 5, 10,
13 and 26.
Key Index: Only valid when using Open authentication
mode and WEP encryption. There are 1~4 key index.
Key Material: The key material can be used to ensure the
security of your wireless network. Fill in the appropriate
value or phrase in Key Material field.
Show Password: Check this box to show the passwords
that have been entered.
OK: Click to save and apply the new settings.
Cancel: Click to leave and discard the settings.
Connect

Rotate
Disconnect

Export Profile

Command to connect to the selected network inside
credentials. The active selected credential is as like as the
active selected Profile.
Command to rotate to connect to the next network inside
credentials.
Stop WPS action and disconnect this active link. And
then select the last profile at the Profile Page. If there is
an empty profile page, the driver will select any
non-security AP.
Export all credentials to Profile.
- 32 -

Delete an existing credential. And then select the next
credential if exist. If there is an empty credential, the
driver will select any non-security AP.

Delete

Start to add to Registrar using PIN (Personal
Identification Number) configuration method. If STA
Registrar, remember that enter PIN Code read from your
Enrollee before starting PIN.

PBC

Start to add to AP using PBC (Push Button
Configuration) method.

WPS Associate IE

Send the association request with WPS IE during WPS
setup. It is optional for STA.

WPS Probe IE

Send the probe request with WPS IE during WPS setup. It
is optional for STA.

Auto

Check this box the device will connect the AP
automatically.

Progress Bar

Display rate of progress from Start to Connected status.

Status Bar

Display currently WPS Status.

Radio On/Off
Click this Radio On/Off button to turn ON or OFF radio function.

This icon shows radio on, click to turn it off.
This icon shows radio off, click to turn it on.
- 33 -

About
This page displays the information of the wireless card including, Config Version/
Date, Driver Version/ Date, EEPROM Version, Firmware Version and
Phy_Address.

- 34 -

Utility Menu List
To access the utility menu list, please right click the utility icon on the task bar.

Launch Config Utility: Select to open the utility screen.

Use Zero Configuration as Configuration Utility: Select to use the
Window XP built-in utility (Zero configuration utility).

Switch to AP Mode: Select to make your wireless USB adapter act as a
wireless AP.

Exit: Select to close the utility program.

- 35 -

Soft AP mode
Config

Config
SSID

AP name of user type. User also can click Use Mac
Address button to display it.

Channel

Manually force the AP using the channel. The
system default is CH 1.

Wireless mode

Here supports 2.4G (included 802.11b/g/n) wireless
mode.

Use Mac Address

Click this button to replace SSID by MAC address.

Security Setting

Authentication mode and encryption algorithm used
within the AP. The system default is no
authentication and encryption.
- 36 -

Authentication Type: There are several types of
authentication modes including Open, Shared,
WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK.
Encryption Type: For Open and Shared
authentication mode, the selections of encryption
type are Not Use and WEP. For WPA-PSK,
WPA2-PSK, and WPA-PSK/ WPA2-PSK
authentication mode, the encryption type supports
both TKIP and AES.
WPA Pre-shared Key: This is the shared secret
between AP and STA. For WPA-PSK and
WPA2-PSK and WPA-PSK/ WPA2-PSK
authentication mode, this field must be filled with
character longer than 8 and less than 64 lengths.
Group Re-key Interval: Only valid when using
WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK authentication mode to renew key. User
can set to change by seconds or packets. Default is
600 seconds.
- 37 -

WEP Key: Only valid when using WEP encryption
algorithm. The key must match with the AP’s key.
There are two formats to enter the keys.
• Hexadecimal (128bits): 26 Hex characters.
• ASCII (128bits): 13 ASCII characters.
Show Password: Check this box to show the
password you entered.
Beacon (ms)

TX Power

Idle time(60-3600)(s)

No forwarding
among wireless
clients
Hide SSID
Allow BW 40MHz
Tx BURST
Default
Apply

The time between two beacons. The system default
is 100 ms.
Manually force the AP transmits power from the
pull down list 100%, 75%, 50%, 25% and lowest.
The system default is 100%.
It represents that the AP will idle after few seconds.
The time must be set between 60~3600 seconds.
Default value of idle time is 300 seconds.
No beacon among wireless client, clients can share
information each other. The system default is no
forwarding.
Do not display AP name. System default no hide.
Click to disable this function. Default is enabled.
Check to enable this function.
Use the system default value.
Click to apply the above settings.

- 38 -

Access Control

Access Control
Access Policy

User chooses whether AP start the function or not.
System default is Disable.
z Disable: Do not use this access control function.
z Allow All: Only the MAC address listed in the
Access List can connect with this soft AP.
z Reject All: Only the MAC address listed in the
Access List can NOT connect with this soft AP.

Mac Address

Manually force the Mac address using the function. Click
Add and the MAC address will be listed in the Access
List pool.

Access List

Display all Mac Address that you have set.
- 39 -

Add

Add the MAC address that you would like to set.

Delete

Delete the Mac address that you have set.

Remove All

Remove all Mac address in the Access List.

Apply

Apply the above changes.

MAC Table

MAC Table
MAC Address

The station MAC address of current connection.

AID

Raise value by current connection.

Power Saving Mode

The station of current connect whether it have to
support.

Status

The status of current connection.
- 40 -

Event Log

Event Log
Event Time
(yy/mm/dd-hh:mm:ss)

Records the event time.

Message

Records all the event messages.

- 41 -

Statistics

Transmit Statistics
Frames Transmitted
Successfully

Frames successfully sent.

Frames Fail To Receive ACK
After All Retries

Frames failed transmit after hitting retry
limit.

RTS Frames Successfully
Receive CTS

Successfully receive CTS after sending RTS
frame

RTS Frames Fail To Receive
CTS

Failed to receive CTS after sending RTS.

Frames Transmitted
Successfully After Retry

Frames successfully sent with one or more
reties.

- 42 -

Receive Statistics
Frames Received Successfully

Frames Received Successfully

Frames Received With CRC
Error

Frames received with CRC error.

Frames Dropped Due To
Out-of-Resource

Frames dropped due to resource issue

Duplicate Frames Received

Duplicate received frames.

Reset Counter

Reset counters to zero.

About
This page displays the wireless card and driver version information.

- 43 -

UTILITY CONFIGURATION FOR
WINDOWS VISTA
After the Wireless adapter has been successfully installed, users can use the
included Configuration Utility to set their preference.
Go to StartJ (All) ProgramJ Intelligent WirelessJ Intelligent Wireless
Utility.

You can also open the Configuration Utility by double clicking the icon or right
clicking to select Launch Config Utility.

- 44 -

Station Mode
Profile
Profile can book keeping your favorite wireless setting among your home, office,
and other public hot-spot. You may save multiple profiles, and activate the correct
one at your preference. The Profile manager enables you to Add, Edit, Delete and
Activate profiles.
Click this button to show the information of Status Section.
Click this button to hide the information of Status Section.

Profile Tab
Profile Name

You may enter a distinctive name of profile in this
column. The default is PROF# (# 1, #2, #3....)

SSID

The SSID is the unique name shared among all points in
your wireless network.

Network Type

Shows the network type of the device, including
Infrastructure and Ad-Hoc.

- 45 -

Authentication

Shows the authentication mode.

Encryption

Shows the encryption type.

Use 802.1x

Whether use 802.1x feature or not.

Tx Power

Transmit power, the amount of power used by a radio
transceiver to send the signal out.

Channel

Shows the selected channel that is currently in use.

Power Save
Mode

Choose from CAM (Constantly Awake Mode) or PSM
(Power Saving Mode.)

RTS Threshold

Shows the RTS Threshold of the device.

Fragment
Threshold

Shows the Fragment Threshold of the device.

Add

Click to add a profile from the drop-down screen.
System Configuration tab:

- 46 -

Profile Name: User can enter profile name, or use default
name defined by system. The default is PROF# (# 1, #2,
#3....).
SSID: The SSID is the unique name shared among all
points in your wireless network. The name must be
identical for all devices and points attempting to connect
to the same network. User can use pull-down menu to
select from available APs.
Network Type: There are two types, Infrastructure and
Ad hoc modes.
• The Infrastructure is intended for the connection
between wireless network cards and an Access Point.
With the wireless adapter, you can connect wireless
LAN to a wired global network via an Access Point.
• The Ad hoc lets you set a small wireless workgroup
easily and quickly. Equipped with the wireless adapter,
you can share files and printers between each PC and
laptop.
- 47 -

Tx Power: Transmit power, the amount of power used by
a radio transceiver to send the signal out. Select the Tx
power percentage from the pull-down list including Auto,
100%, 75%, 50%, 25%, 10% and Lowest.
Preamble: This function will show up when Ad-hoc
network type be selected. A preamble is a signal used in
wireless environment to synchronize the transmitting
timing including Synchronization and Start frame
delimiter. Select from the pull-down menu to change the
Preamble type into Auto or Long.
RTS Threshold: User can adjust the RTS threshold
number by sliding the bar or key in the value directly. The
default value is 2347. RTS/CTS Threshold is a mechanism
implemented to prevent the “Hidden Node” problem. If
the “Hidden Node” problem is an issue, users have to
specify the packet size. The RTS/CTS mechanism will be
activated if the data size exceeds the value you set. This
value should remain at its default setting of 2347. Should
you encounter inconsistent data flow, only minor
modifications of this value are recommended.
Fragment Threshold: User can adjust the Fragment
threshold number by sliding the bar or key in the value
directly. The default value is 2346. The mechanism of
Fragmentation Threshold is used to improve the efficiency
when high traffic flows along in the wireless network. If
your Wireless LAN Adapter often transmits large files in
wireless network, you can enter new Fragment Threshold
value to split the packet. The value can be set from 256 to
2346.
Authentication and Encryption tab:

- 48 -

Authentication Type: There are six type of authentication
modes including Open, Shared, WPA, WPA-PSK, WPA2
and WPA2-PSK.
• Open: If your access point/ wireless router is using
"Open” authentication, then the wireless adapter will
need to be set to the same authentication type.
• Shared: Shared key is when both the sender and the
recipient share a secret key.
• WPA/ WPA-PSK/ WPA2/ WPA2-PSK: WPA-PSK
offers two encryption methods, TKIP and AES. Select
the type of algorithm, TKIP or AES and then enter a
WPA Shared Key of 8-63 characters in the WPA
Pre-shared Key field.
Encryption Type: For Open and Shared authentication
mode, the selection of encryption type are None and WEP.
For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication mode, the encryption type supports both
TKIP and AES.
- 49 -

WPA Pre-shared Key: This blank is the shared secret
between AP and STA. For WPA-PSK and WPA2-PSK
authentication mode, this field must be filled with
character longer than 8 and less than 64 lengths.
WEP Key: Only valid when using WEP encryption
algorithm. The key must match with the AP’s key. There
are several formats to enter the keys.
• Hexadecimal (128bits): 26 Hex characters (0~9, a~f).
• ASCII (128bits): 13 ASCII characters.
Show Password: Check this box to show the password
you entered.
802.1x Setting: When user use radius server to
authenticate client certificate for WPA authentication
mode.
802.1x tab:

EAP Method:
- 50 -

• PEAP: Protect Extensible Authentication Protocol.
PEAP transport securely authentication data by using
tunnelling between PEAP clients and an authentication
server. PEAP can authenticate wireless LAN clients
using only server-side certificates, thus simplifying the
implementation and administration of a secure
wireless LAN.
•

TLS / Smart Card: Transport Layer Security.
Provides for certificate-based and mutual
authentication of the client and the network. It relies
on client-side and server-side certificates to perform
authentication and can be used to dynamically
generate user-based and session-based WEP keys to
secure subsequent communications between the
WLAN client and the access point.

Tunnel Authentication:
•

Protocol: Tunnel protocol, List information including
EAP-MSCHAP v2 and EAP-TLS/ Smart Card.

•

Tunnel Identity: Identity for tunnel.

•

Tunnel Password: Password for tunnel.

Session Resumption: Reconnect the signal while broken
up, to reduce the packet and improve the transmitting
speed. User can click the box to enable or disable this
function.
ID\PASSWORD tab:

- 51 -

ID/ PASSWORD: Identity and password for server.
•

Authentication ID / Password: Identity, password
and domain name for server. Only "EAP-FAST" and
"LEAP" authentication can key in domain name.
Domain name can be keyed in blank space.

•

Tunnel ID / Password: Identity and Password for
server.

Show Password: Check this box to show the password
you entered.
OK: Click to save settings and exit this page.
Cancel: Click to call off the settings and exit.
Client Certification tab:

You can select Use a certificate on this computer, a
client certificate for server authentication. Or you can
select Use my smart card to enable the Client
- 52 -

Certification function.
OK: Click to save settings and exit this page.
Cancel: Click to call off the settings and exit.
Server Certification tab:

Use certificate chain: Choose use server that issuer of
certificates.
Server name: Enter an authentication sever name.
OK: Click to save settings and exit this page.
Cancel: Click call off the settings and exit.
Delete

Click to delete an existing profile.

Edit

Click to edit a profile.

Activate

Click to make a connection between devices.

- 53 -

Network Tab
Sorted by

Indicate that AP list are sorted by SSID, Channel or Signal.

Show dBm

Check the box to show the dBm of the AP list.

SSID

Shows the name of BSS network.

Network Type

Network type in use, Infrastructure for BSS, Ad-Hoc for
IBSS network.

Channel

Shows the currently used channel.

Wireless mode

AP support wireless mode. It may support 802.11b or
802.11g or 802.11n wireless mode.

Encryption

Shows the encryption type currently in use. Valid value
includes WEP, TKIP, AES, and Not Use.

Signal

Shows the receiving signal strength of specified network.

Rescan

Click to refresh the AP list.

Add to Profile

Select an item on the list and then click to add it into the
profile list.

AP information
When you double click on the intended AP, you can see AP's detail information
that divides into three parts. They are General, WPS, CCX information. The
introduction is as following:
- 54 -

General

WPS information contains Authentication Type, Encryption
Type, Config Methods, Device Password ID, Selected
Registrar, State, Version, AP Setup Locked, UUID-E and
RF Bands.
Authentication Type: There are four types of
authentication modes supported by RaConfig. They are
Open, Shared, WPA-PSK and WPA system.
Encryption Type: For open and shared authentication
mode, the selection of encryption type are None and WEP.
For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication mode, the encryption type supports both
TKIP and AES.
Config Methods: Correspond to the methods the AP
supports as an Enrollee for adding external Registrars.
- 55 -

Device Password ID: Indicate the method or identifies the
specific password that the selected Registrar intends to use.
Selected Registrar: Indicate if the user has recently
activated a Registrar to add an Enrollee. The values are
"TRUE" and "FALSE".
State: The current configuration state on AP. The values
are "Unconfigured" and "Configured".
Version: WPS specified version.
AP Setup Locked: Indicate if AP has entered a setup
locked state.
UUID-E: The universally unique identifier (UUID) element
generated by the Enrollee. There is a value. It is 16 bytes.
RF Bands: Indicate all RF bands available on the AP. A
dual-band AP must provide it. The values are "2.4GHz".
Close: Click this button to exit the information screen.
CXX

CCX information contains CCKM, Cmic and Ckip
information.
Close: Click this button to exit the information screen.
802.11n

- 56 -

This tab will show up if you select the AP that support 11n
mode. Here shows the connected AP 802.11n related
information.

- 57 -

Link Status Tab
Status

Shows the current connected AP SSID and MAC
address. If there is no connection existing, it will show
Disconnected.

Extra Info

Shows the link status and Tx power percentage.

Channel

Shows the current channel in use.

Authentication

Authentication mode used within the network,
including Unknown, Open, WPA-PSK, WPA2-PSK,
WPA and WPA2.

Encryption

Shows the encryption type currently in use. Valid
value includes WEP, TKIP, AES, and Not Use.

Network Type

IP Address
Sub Mask
Default Gateway
Link Quality

Signal Strength 1

Noise Strength

Network type in use, Infrastructure for BSS, Ad-Hoc
for IBSS network.
Shows the IP address information.
Shows the Subnet Mask information.
Shows the default gateway information.
Shows the connection quality based on signal strength
and TX/RX packet error rate.
Shows the Receiving signal strength, you can choose
to display as percentage or dBm format.
Shows the noise signal strength in the wireless
environment.
- 58 -

Transmit

Receive

Link Speed
Throughput

Shows the current Link Speed and Throughput of the
transmit rate.
Shows the current Link Speed and Throughput of
receive rate.
Shows the current transmitting rate and receiving rate.
Shows the transmitting and receiving speed of data.

Advanced
This Advanced page provides advanced and detailed settings for your wireless
network.

Advanced Tab
Wireless mode
Enable TX Burst

Here supports 2.4G (included 802.11b/g/n) wireless mode.
Check to enable this function. This function enables the
adapter to deliver better throughput during a period of
- 59 -

time, it only takes effect when connecting with the AP
that supports this function.
Enable TCP
Window Size
Fast Roaming at

Apply

Check to increase the transmission quality. The large TCP
window size the better performance.
Check to set the roaming interval, fast to roaming, setup
by transmits power.
Click to apply above settings.

Statistics
The Statistics screen displays the statistics on your current network settings.

Transmit Statistics Tab
Frames Transmitted Successfully Shows information of frames successfully
sent.
Frames Retransmitted
Successfully

Shows information of frames successfully
sent with one or more reties.

Frames Fail To Receive ACK
After All Retries

Shows information of frames failed
- 60 -

transmit after hitting retry limit.
RTS Frames Successfully Receive Shows information of successfully receive
CTS after sending RTS frame
CTS
RTS Frames Fail To Receive
CTS

Shows information of failed to receive CTS
after sending RTS.

Reset Counter

Click this button to reset counters to zero.

Receive Statistics Tab
Frames Received Successfully

Shows information of frames Received
Successfully.

Frames Received With CRC
Error

Shows information of frames received with
CRC error.

Frames Dropped Due To
Out-of-Resource

Shows information of frames dropped due
to resource issue.

Duplicate Frames Received

Shows information of frames received
more than twice.

Reset Counter

Click this button to reset counters to zero.

- 61 -

WMM / QoS
The WMM page shows the Wi-Fi Multi-Media power save function and Direct
Link Setup that ensure your wireless network quality.

WMM/QoS Tab
WMM Enable

Check the box to enable Wi-Fi Multi-Media
function that is meant to improve audio, video
and voice applications transmitted over Wi-Fi.

WMM- Power Save Enable Select which ACs you want to enable the power
saving mode.
AC_BK (Access Category Background)
AC_BE (Access Category Best Effort)
AC_VI (Access Category Video)
AC_VO (Access Category Voice)
Direct Link Setup Enable
MAC Address

Check the box to enable Direct Link Setup.
The setting of DLS(Direct Link Setup) indicates
as follow:
Fill in the blanks of Direct Link with MAC
Address of STA, and the STA must conform to
two conditions:
• Connecting with the same AP that supports
DLS feature.
- 62 -

•

DLS enabled.

Timeout Value

Apply

Click this button to apply the settings.

Tear Down

Select a direct link STA, then click "Tear Down"
button to disconnect the STA.

WPS Tab
WPS AP List

Display the information of surrounding APs with WPS IE
from last scan result. List information included SSID,
- 63 -

BSSID, Channel, ID (Device Password ID),
Security-Enabled.
Rescan

Issue a rescan command to wireless NIC to update
information on surrounding wireless network.

Information

Display the information about WPS IE on the selected
network. List information included Authentication Type,
Encryption Type, Config Methods, Device Password ID,
Selected Registrar, State, Version, AP Setup Locked,
UUID-E and RF Bands.

PIN Code

8-digit numbers. It is required to enter PIN Code into
Registrar when using PIN method. When STA is
Enrollee, you can use "Renew" button to re-generate new
PIN Code.

Config Mode

Select from the pull-down menu to decide the station
role-playing as an Enrollee or an external Registrar.

Detail

Click the Detail button to show the information about
Security and Key in the credential.

- 64 -

If you select the AP that listed in the WPS Profile List
field, you can click the Detail button to see more AP
information.
SSID: Shows the connected AP network name.
BSSID: The MAC address of the connected AP. Fixed
and cannot be changed.
Authentication Type: The authentication type support
Open, WPA-PSK and WPA2-PSK.
Encryption Type: For Open authentication mode, the
selection of encryption type are NONE and WEP. For
WPA-PSK and WPA2-PSK authentication mode, the
encryption type supports both TKIP and AES.
Key Length: Only valid when using Open authentication
mode and WEP encryption. There are key lengths 5, 10,
13 and 26.
Key Index: Only valid when using Open authentication
mode and WEP encryption. There are 1~4 key index.
Key Material: The key material can be used to ensure the
security of your wireless network. Fill in the appropriate
value or phrase in Key Material field.
Show Password: Check this box to show the passwords
that have been entered.
OK: Click to save and apply the new settings.
Cancel: Click to leave and discard the settings.
Connect

Command to connect to the selected network inside
credentials. The active selected credential is as like as the
active selected Profile.

Rotate

Command to rotate to connect to the next network inside
credentials.

Disconnect

Stop WPS action and disconnect this active link. And
- 65 -

then select the last profile at the Profile Page. If there is
an empty profile page, the driver will select any
non-security AP.
Export Profile

Export all credentials to Profile.

Delete

Delete an existing credential. And then select the next
credential if exist. If there is an empty credential, the
driver will select any non-security AP.

Start to add to Registrar using PIN (Personal
Identification Number) configuration method. If STA
Registrar, remember that enter PIN Code read from your
Enrollee before starting PIN.

PBC

Start to add to AP using PBC (Push Button
Configuration) method.

WPS Associate IE

Send the association request with WPS IE during WPS
setup. It is optional for STA.

WPS Probe IE

Send the probe request with WPS IE during WPS setup. It
is optional for STA.

Progress Bar

Display rate of progress from Start to Connected status.

Status Bar

Display currently WPS Status.

Radio On/Off
Click this button to turn on or off radio function.

This icon shows radio on, click to turn it off.
This icon shows radio off, click to turn it on.
- 66 -

About
This page displays the information of the wireless card including, RaConfig
Version/ Date, Driver Version/ Date, EEPROM Version and Phy_Address.

Utility Menu List
To access Windows Vista utility menu list, please right click the utility icon on
the task bar.

Launch Config Utility: Select to open the utility screen.

Switch to AP Mode: Select to make your wireless USB adapter act as a
wireless AP.

Exit: Select to close the utility program.

- 67 -

Soft AP mode
Config

Config
SSID

AP name of user type. User also can click Use Mac
Address button to display it.

Channel

Manually force the AP using the channel. The system
default is CH 1.

Wireless mode

Here supports 2.4G (included 802.11b/g/n) wireless
mode.

Use Mac Address

Click this button to replace SSID by MAC address.

Security Setting

Authentication mode and encryption algorithm used
within the AP. The system default is no
authentication and encryption.
- 68 -

Authentication Type: There are several types of
authentication modes including Open, Shared,
WPA-PSK, WPA2-PSK, and
WPA-PSK/WPA2-PSK.
Encryption Type: For Open and Shared
authentication mode, the selections of encryption
type are Not Use and WEP. For WPA-PSK,
WPA2-PSK, and WPA-PSK/ WPA2-PSK
authentication mode, the encryption type supports
both TKIP and AES.
WPA Pre-shared Key: This is the shared secret
between AP and STA. For WPA-PSK and
WPA2-PSK and WPA-PSK/ WPA2-PSK
authentication mode, this field must be filled with
character longer than 8 and less than 64 lengths.
Group Re-key Interval: Only valid when using
WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK authentication mode to renew key. User
can set to change by seconds or packets. Default is
600 seconds.
- 69 -

WEP Key: Only valid when using WEP encryption
algorithm. The key must match with the AP’s key.
There are several formats to enter the keys.
•
•
•
•

Hexadecimal (64bits): 10 Hex characters.
Hexadecimal (128bits): 26 Hex characters.
ASCII (64bits): 5 ASCII characters.
ASCII (128bits): 13 ASCII characters.

Show Password: Check this box to show the
password you entered.
Beacon (ms)

The time between two beacons. The system default is
100 ms.

TX Power

Manually force the AP transmits power from the pull
down list 100%, 75%, 50%, 25% and Lowest. The
system default is 100%.

Idle time(60-3600)(s)

It represents that the AP will idle after few seconds.
The time must be set between 60~3600 seconds.
Default value of idle time is 300 seconds.

No forwarding
among wireless
clients

No beacon among wireless client, clients can share
information each other. The system default is no
forwarding.

Hide SSID

Do not display AP name. System default no hide.

Allow BW 40MHz

Click to disable this function. Default is enabling.

Default

Use the system default value.

Apply

Click to apply the above settings.

- 70 -

Access Control

Access Control
Access Policy

MAC Address

Manually force the Mac address using the function. Click
Add and the MAC address will be listed in the Access
List pool.

Access List

Display all MAC Address that you have set.
- 71 -

Add

Add the MAC address that you would like to set.

Delete

Delete the MAC address that you have set.

Remove All

Remove all MAC address in the Access List.

Apply

Apply the above changes.

MAC Table

MAC Table
MAC Address

The station MAC address of current connection.

AID

Raise value by current connection.

Power Saving Mode

The station of current connect whether it have to
support.

Status

The status of current connection.
- 72 -

Event Log

Event Log
Event Time
(yy/mm/dd-hh:mm:ss)

Records the event time.

Message

Records all the event messages.

- 73 -

Statistics

Transmit Statistics
Frames Transmitted
Successfully

Frames successfully sent.

Frames Fail To Receive ACK
After All Retries

Frames failed transmit after hitting retry
limit.

RTS Frames Successfully
Receive CTS

Successfully receive CTS after sending RTS
frame

RTS Frames Fail To Receive
CTS

Failed to receive CTS after sending RTS.

Frames Transmitted
Successfully After Retry

Frames successfully sent with one or more
reties.
- 74 -

Receive Statistics
Frames Received Successfully

Frames Received Successfully

Frames Received With CRC
Error

Frames received with CRC error.

Frames Dropped Due To
Out-of-Resource

Frames dropped due to resource issue

Duplicate Frames Received

Duplicate received frames.

Reset Counter

Reset counters to zero.

About
This page displays the wireless card and driver version information.

- 75 -

UNINSTALLATION FOR WINDOWS
2000/XP
In case you need to uninstall the Utility and driver, please refer to below steps.
(As you uninstall the utility, the driver will be uninstalled as well.)

Go to Start ÆAll Programs ÆIntelligent Wireless Æ
Uninstall –Intelligent.

- 76 -

Click Yes to complete remove the selected application and all of its
features.

Then click Finish to complete the uninstallation.

- 77 -

UNINSTALLATION FOR WINDOWS
VISTA
In case you need to uninstall the utility and driver, please refer to below steps. (As
you uninstall the utility, the driver will be uninstalled as well.)

Go to Start Æ Programs ÆIntelligent Wireless Æ
Uninstall –Intelligent.

- 78 -

Click Yes to complete remove the selected application and all of its
features.

Then click Finish to complete the uninstallation.

- 79 -

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:08:11 11:01:58+08:00
Create Date                     : 2008:08:11 11:01:58+08:00
Format                          : application/pdf
Title                           : Microsoft Word - WU5205_MNL_English plus Vista.doc
Creator                         : A1787
Document ID                     : uuid:744a0e7b-a940-4c56-a98d-47343cddbfb0
Instance ID                     : uuid:16c14115-3e0c-4099-9de8-9393be562a5b
Page Count                      : 85
Author                          : A1787

EXIF Metadata provided by EXIF.tools

Abocom Wu5205 Users Manual WU5205_MNL_English Plus Vista

WU5205 to the manual 52825e7d-80bc-4f41-8481-8d3c944bffb5

Navigation menu

Versions of this User Manual:

Views

Navigation