Accton Technology 3CRWE850075 Wireless LAN Access Point 8500 User Manual 09 2292 00AC

Accton Technology Corp Wireless LAN Access Point 8500 09 2292 00AC

UserManual.wiki >

Accton Technology >

3CRWE850075 User Manual

Quick Start Guide

Quick Start Guide Wireless LAN Access Point 8200/8500/8700 3CRWE820096A3CRWE850075A3CRWE870075A The 3Com Wireless LAN Access Point 8200 , Access Point 8500, and Access Point 8700 offer enterprise network standard based security and complete centralized management, with ﬂexible and expansive connectivity and scalability. They extend networks and boost productivity for centrally managed enterprises requiring scalable security solutions. NOTE: This product must be installed by a professional technician/installer. Caution: Do not connect a telephone cable into the Console port; doing so can cause serious damage to the access point.LEDsResetbutton Console portEthernet portAccess Point 8500 Access Point 8200/8700 09-2292-00AC.fm Page 1 Tuesday, March 11, 2003 3:53 PM

1 Before You Start ■ Make sure that you have the following items ready for the installation: ■ 3Com Access Point 8200, Access Point 8500, or Access Point 8700 ■ Standard detachable antennas (Access Point 8200 or Access Point 8700) ■ 3Com installation CD ■ Ethernet category 5 straight cables (8-wire) ■ For wall-mount installations you will need the following items: Mounting plateMounting screwsPlastic anchors for drywall mounting ■ 3Com Integrated Power-over-Ethernet power supply and power cord ■ To use the Web conﬁguration management system, you need a computer running one of the following operating systems and one of the following browsers: ■ Operating Systems : Windows 98, Windows ME, Windows NT 4.0 (with the latest service pack), Windows 2000, or Windows XP. ■ Browsers : Internet Explorer 5.0 or later. (Internet Explorer 5.5 is available on the installation CD.) 2 Prepare for Installation It is advisable to connect the power and check the Ethernet cables and LEDs before installing the unit in a hard-to-reach location. 1 Observe the following power requirements: The access point complies with the IEEE 802.3af power-over-Ethernet standard. It receives power over category 5 straight cable. Installation requires the use of either the 3Com power supply provided or IEEE 802.3af compliant power supply equipment (output power rated 48 V DC @ 350 mA maximum). Such equipment must be safety certiﬁed according to UL, CSA, IEC or other applicable national or international safety requirements for the country of use. All references to the power supply refer to equipment that meets these requirements. Because the power supply plug is the only means of disconnecting the access point from power, make sure the power outlet is accessible.The power supply can be located indoors at any point between the access point and the LAN access port where an accessible power outlet exists. 2 Decide where to place the access point. ■ Mounted on a wall on a stud (or other hard surface) ■ Mounted on to drywall ■ Placed on a ﬂat surface The location should be elevated and centrally located relative to users on your network. Ceiling mounting is not recommended. 3 Record the access point MAC address in a safe place before the access point is installed in a hard-to-reach location. The MAC address is printed on the back of the access point housing. 4 Access Point 8200 or Access Point 8700: Carefully unpack the standard detachable antennas. Screw the antennas on to the SMA connectors and hand-tighten them. After network startup, you may need to adjust the antennas to ﬁne-tune coverage in your area.NOTE: Regulatory restrictions dictate that when the access point is operational a minimum body-to-antenna distance of 1 meter (3 feet) must be maintained. 09-2292-00AC.fm Page 2 Tuesday, March 11, 2003 3:53 PM

The installation CD includes the User Guide, which contains more detailed information on planning, installing and conﬁguring the device. Additional tools and utilities are provided to assist with the management of your network. See “Documentation and Software Utilities” on page 7 for instructions. 3 Connect the Power The access point complies with the IEEE 802.3af power-over-Ethernet standard. It receives power over a standard category 5 straight (8-wire) Ethernet cable. There are two ways to supply power to the access point (refer to the illustration below): ■ Use the supplied 3Com Integrated Power-over-Ethernet power supply. In this case, you need to supply a second Ethernet cable to connect to the wired LAN. ■ Connect the access point directly to your own power-over-Ethernet hub or switch, which must also comply with the IEEE 802.3af standard. Using the Power Supply The power supply can be located at any point between the access point and the LAN access port, wherever a convenient power outlet exists. If you supply your own Ethernet cable for connecting power, be sure that it is standard category 5 straight-through (8-wire) cable that has not been altered in any way. Use of nonstandard cable could damage the access point.Refer to the illustration above, and follow these steps: 1 Connect one end of the Ethernet cable to the Ethernet port on the access point. 2 Connect the other end of the Ethernet cable to the port labeled To Access Point on the power supply. 3 Connect the power cord to the power supply and plug the cord into a power outlet.CAUTION: Do not handle the antenna tips, especially after they are connected to the access point, as this could lead to electrostatic discharge (ESD), which could damage the equipment."To Access Point""To Hub/Switch"Using the Power Supply Using A Power-over-EthernetLAN Port 09-2292-00AC.fm Page 3 Tuesday, March 11, 2003 3:53 PM

4 To link the access point to your Ethernet network, plug one end of another Ethernet cable into the port labeled To Hub/Switch on the power supply, and plug the other end into a LAN port (on a hub or in a wall). Using a Power-Over-Ethernet LAN Port If your LAN equipment complies with the IEEE 802.3af power-over-Ethernet standard, you can connect the access point directly to a LAN port. For example, the illustration above right shows a connection through a 3Com Ethernet Power Supply to a 3Com SuperStack ® Switch. 4 Check the LEDs When power is connected, the access point LEDs light. The illustration and the following table describe the LEDs and their functions. CAUTION: To avoid damaging network equipment, make sure that the cables are connected from access point to power supply to LAN as shown and described above. Name Description Radio LED blinks red to indicate radio activity. Faster blinking indicates more activity.Power LED lights green when operational code is running.Reset ButtonPress this button in for 15 seconds to restore the factory defaults.Ethernet LED lights yellow when Ethernet link is established. LED blinks to indicate activity on the Ethernet. Faster blinking indicates more activity.Radio LED blinks red to indicate radio activity. Faster blinking indicates more activity. This LED is only active when a second radio is installed.ResetButton 09-2292-00AC.fm Page 4 Tuesday, March 11, 2003 3:53 PM

5 Wall Mount Installation 1 Install the mounting plate as shown in the following illustration, on either a stud (or other hard wall surface), or onto drywall. ■ Allow for a clearance of at least 25 cm (10 Inches) between the ceiling and the top of the mounting plate. ■ Make sure that “UP” is correctly oriented, and align the mounting plate screw holes vertically. ■ For installation on a wall stud, install the top screw into the stud, as shown at left in the illustration, and then vertically align the mounting plate before installing the bottom screw. ■ For installation on to drywall, mark three screw holes using the mounting plate as a template for vertical alignment, as shown at right in the illustration above. ■ Use a 5-mm (3/16-in.) drill bit if using the plastic anchors provided. ■ For drywall mounts, you can route the cable through either a side or center opening for a seamless appearance using one of the methods illustrated below. Alternatively, you can simply attach the Ethernet cable to the side of the unit, allowing it to trail along the wall. ■ If you have routed the Ethernet cable through the center opening, secure the cable on the hook located on the mounting plate as shown in the illustration below. 2 Connect the Ethernet cable to the Ethernet port on the access point. 3 Position the access point at an angle to the mounting plate bayonet connection and turn the unit clockwise until it snaps into place, as shown below.If installing into drywall, use3 plastic anchors and 3 screws.If installing into a stud or othersecure vertical surface, use 2 screws. 09-2292-00AC.fm Page 5 Tuesday, March 11, 2003 3:53 PM

6 Flat Surface Installation 1 Find a clean and dry surface that is elevated enough to provide good reception and coverage for the network. Do not place the access point on a metal surface. 2 Make sure to choose a location where the access point will not be disturbed. 3 Connect the Ethernet cable into the Ethernet port. 4 Set the access point down on a ﬂat, level surface. 7 Antenna Adjustment (Access Point 8200/8700) Position the antennas so that they turn away from the access point at approximately a 45-degree angle. Your particular location might require additional antenna adjustment. CAUTION: Do not handle the antenna tips, especially after they are connected to the access point, as this could lead to electrostatic discharge (ESD), which could damage the equipment.Hold the access point at an angle. Turnclockwise to engage and secure it onthe mounting plate.Leave at least 13 cm (5 in.) length. Ethernet cable may be routed throughcenter opening or through the side.CenteropeningSide openingHook for securingthe cableConnectEthernet cable.Rotate forbest reception. 09-2292-00AC.fm Page 6 Tuesday, March 11, 2003 3:53 PM

8 Documentation and Software Utilities The installation CD includes documentation and software utilities to help you set up and administer the wireless components of your network. To view product documentation, select View the Documentation from the CD Startup Menu and then select the item you wish to view. To install utilities, select Tools and Utilities from the CD Startup Menu. Select the items you wish to install and follow the onscreen instructions. The software Tools and Utilities include: ■ 3Com Wireless Infrastructure Device Manager. Use this tool to discover access points and select devices for administrative changes. ■ 3Com 3CDaemon Server Tool. This tool can act in four different capacities: ■ As a TFTP Server, necessary for ﬁrmware upgrades, and backup and restore functions. Use this option if you do not have a TFTP server set up. ■ As a SysLog Server, which is necessary to view SysLog messages. ■ As an optional TFTP Client. ■ As an optional FTP Server. ■ 3Com Network Supervisor v4.01. The 3Com Network Supervisor (3NS) v4.01 graphically discovers, maps, and displays network links and IP devices, including 3Com wireless access points. It is not required for access point management. ■ Internet Explorer 5.5. This browser is included for your those who do not have a suitable browser. 9 Conﬁguration Notes ■ For a new access point installation, the default WLAN Service Area (ESSID) is 3Com, no security is set, and channel selection is set to Channel 11. Also, unless it detects a DHCP server on the network, the access point uses Auto IP to assign an IP address of the form 169.254.xxx.yyy, where xxx and yyy are random numbers. ■ Use the 3Com Wireless Infrastructure Device Manager to locate 3Com Wireless LAN devices and launch their conﬁgurations. When installing the device manager, make sure the computer is connected to the same network as the device to be conﬁgured. After installing and launching the device manager, select the device to be conﬁgured from network tree and click Conﬁgure to launch the conﬁguration Web interface. Refer to the Access Point 8200/8500/8700 User Guide (included on the installation CD) for detailed information and instructions on locating and conﬁguring access points. ■ If you experience difﬁculty with the installation, see the Troubleshooting section of the User Guide.For the latest networking information, see the 3Com Corporation World Wide Web site: http://www.3com.com/. 10 Regulatory Information This product is in compliance with the essential requirements of Directive 1999/5/EC. Channel Selection in France In France, this product must be conﬁgured to operate on a legal channel. Channels 10 - 13 are allowed. User documentation should be consulted to ensure that this product is used in accordance with local spectrum restrictions. 09-2292-00AC.fm Page 7 Tuesday, March 11, 2003 3:53 PM

Navigation menu