Ace Hardware Jet Tank System R 30 T7 Users Manual 23833A343 R30

R-30-T7 to the manual 8e1d3ca7-a257-4990-b2ba-b246769da75f

2015-02-05

: Ace-Hardware Ace-Hardware-Jet-Tank-System-R-30-T7-Users-Manual-504155 ace-hardware-jet-tank-system-r-30-t7-users-manual-504155 ace-hardware pdf

Open the PDF directly: View PDF .
Page Count: 10

23833A343

JET TANK

SYSTEM

with 7-gallon

diaphragm

pressure

tank

MODEL R-30-T7

1/3 Horse Power

Convertible Pump

WATER ACE PUMP COMPANY • ASHLAND, OHIO 44805-1969

JET TANK SYSTEM

INSTALLATION MANUAL

WARRANTY

PRODUCT DEFECTS

COVERED TWELVE

MONTHS FROM

DATE OF PURCHASE

OR EIGHTEEN

MONTHS FROM

DATE OF MANUFAC-

TURE, WHICHEVER

COMES FIRST. RE-

CEIPT AND PROD-

UCT DATE CODE

REQUIRED FOR

WARRANTY CLAIM.

EASTERN

STANDARD

TIME

CONSUMER HOT-LINE: 1-800-942-3343 • MONDAY - FRIDAY • 7 AM to 5 PM

pump only

23833A343

IMPORTANT INSTRUCTIONS BEFORE INSTALLATION

Failure to follow these instructions may cause serious bodily injury and/or property damage.

Warranty void if product modified, drilled,

painted, or altered in any way; if used to

pump hot water, or to pump liquids other

than water (such as but not limited to chemi-

SHALLOW WELL PUMP CAPACITIES DEEP WELL PUMP CAPACITIES

WARNING

cals, fertilizers, flammable liquids, herbicides, mud,

tar, cement, wood chips); or otherwise abused.

1. Before installing or servicing your pump, BE CER-

TAIN pump power source is disconnected.

2. All installation and electrical wiring must adhere to

state and local codes and must be complete before

priming the pump. Check with appropriate community

agencies, or contact your local electrical and pump

professionals.

3. Pump should be installed in a dry, convenient

location which is close to the well and provides ample

space for installation and servicing the well. A dry

basement, pit, or utility room is an excellent choice

when allowed by law.

4. CALL AN ELECTRICIAN WHEN IN DOUBT. Pump

should be connected to a separate electrical circuit

directly from main switch. There must be a fuse box or

circuit breaker installed in this line. Plugging into exist-

ing outlets may cause low voltage at motor, resulting in

blown fuses, tripping of motor overload, or burned out

motor. Refer to electrical diagrams on following

page for electrical connections.

5. It is mandatory that a permanent ground connection

be made from the pump to the grounding bar at the

service panel. Do not connect pump to a power supply

until permanently grounded. For maximum safety,

ground the pump to a circuit equipped with a fault

interrupter device.

6. Motor Grounding Instructions: WARNING

Reduced risk of electric shock during operation of this

pump requires the provision of acceptable grounding.

Caution: Failure to ground this unit properly may

result in severe electrical shock. If the means of

connection to the supply-connection box is other than

grounded metal conduit, ground the pump back to the

service by connecting a copper conductor, at least the

size of the circuit conductors supplying the pump, to the

grounding screw provided within the wiring compart-

ment. NOTE: N.E.C. requires pumps be grounded at

installation.

7. Voltage of power supply must match the voltage of

the pump which is factory preset to 115V, but may be

rewired for 230V (see following page).

8. During installation, cover well to prevent foreign

matter from contaminating the well or later damaging

the pump during operation. Test well water for purity.

Chlorination may be necessary. Check local Health

Department for proper testing and recommendations.

9. Hand pump new wells until clear. Sand or other

sediment will seriously damage the pump.

10. The 7-gallon diaphragm pressure tank is factory

preset to 30 PSI. It must be reset to 18 PSI for

proper system operation. Use an air gauge to

measure pressure in tank as air is released.

11. The following may cause severe damage to pump

and/or piping and will void warranty:

• Failure to protect pump and piping against below

freezing temperatures.

• Pumping chemicals or corrosive liquids.

• Running the pump dry. Follow priming instructions

on pages 4 or 8, depending on the installation.

•

Using extension cords.

•

Pumping gasoline or other flammable liquids.

•

Using this pump in or near a swimming pool.

PUMPING DEPTH IN FEET

GALLONS PER MINUTE AT 30 PSI PRESSURE

5 10152025

030 40 50 60 70 80 90 100 110

PUMPING DEPTH IN FEET

GALLONS PER MINUTE AT 30 PSI PRESSURE

23833A343

IMPORTANT SELECT

CORRECT VOLTAGE

USE COPPER CONDUCTORS ONLY

VOLTAGE SELECTOR

AT REAR OF MOTOR

(USE NEEDLE

NOSE PLIERS)

PULL SELECTOR -

ROTATE - REINSERT

115

230

115V

230V

HIGH

VOLTAGE LOW

VOLTAGE VOLTAGE

SELECTOR TERMINAL BOARD

GRD

UNGROUNDED

LINE

FINDING THE DEPTH OF YOUR WELL

The jet tank system installs differently depending

on the depth of your well. Tie a small but heavy

weight to the end of a piece of string (be sure there is

enough string; some wells are very deep). Lower the

weight into the well until it reaches the bottom. Take up

the slack and mark the string at ground level. Pull the

weight out of the well and measure from the bottom of

the weight to the ground level mark. This is the depth

of your well. Subtract five feet from the depth of your

well. This number should not exceed the maximum

rated depth for your pump. If it does, it will greatly

hinder or prevent the proper operation of the pump.

115V OR 230V OPERATION

Your pump is equipped with one of two types of dual

voltage motors. Follow the instructions to wire the

motor for the proper voltage. The voltage of the pump

must match the voltage of the power supply.

WIRE SELECTION GUIDE WIRING YOUR PUMP

Remove the cover from the pressure switch. Connect

the bare copper ground to the ground screw in the

pressure switch. Connect the power supply to the

terminals marked "Line" in the diagram below.

NAME

PLATE

AMPS

464

1857

#14 #8

296

1184

189

756

118

475

10.6

5.3

115

230

VOLTAGE MAX. WIRE LENGTH USING AWG SIZE

#12 #10

STANDARD LINE

PLUG FUSE*

LOW PEAK - CART. TYPE

FUSETRON - CART. TYPE

FUSTAT - PLUG TYPE*

CIRCUIT BREAKER

115V 230V 115V 230V

115V 230V

20 10 12 6-1/4 20 15

FUSE AND CIRCUIT

BREAKER SIZE GUIDE

*For circuits not over 150 volts to ground.

LINE

GROUND

MOTOR

23833A343

STEP

1Thread 1-1/4" male PVC

adapter into foot valve.

Hand tighten, then tighten

1/4 turn with crescent

wrench.

Subtract five feet from the

depth of your well (See

page 3 "Finding the Depth

of Your Well"). This is the

STEP

FOOT

VALVE

1-1/4"

MALE PVC

ADAPTER

1-1/4"

MALE PVC

ADAPTER

Cement as many coup-

lings and sections of

rigid PVC pipe as it

takes to equal the depth

of your well minus five

feet, then firmly clamp

the assembly with a

pipe clamp to prevent

assembly from sliding

down into the well.

STEP

total length of rigid PVC pipe and

couplings to cement onto the 1-1/4"

male PVC adapter. Cement one

section of rigid PVC pipe to the PVC

adapter which is connected to the

foot valve, then lower the whole

assembly into the well, foot valve

first. Firmly clamp the end of the

rigid PVC pipe with a pipe clamp to

prevent the assembly from sliding

down into the well.

REMINDER: ALL JOINTS AND CONNECTIONS MUST BE AIRTIGHT. A SINGLE PIN-

HOLE LEAK WILL PREVENT THE PROPER OPERATION OF THE PUMP. USE THREAD

COMPOUND ON ALL THREADED CONNECTIONS UNLESS SPECIFIED OTHERWISE.

SHALLOW WELL PUMP INSTALLATION

(4" DIAMETER CASED WELL)

For wells 25 feet or less in depth, the ejector may be

attached to the front of the tank-mounted jet pump. For

lower depths, the ejector must be placed down inside

the well (see DEEP WELL PUMP INSTALLATION). All

materials with part numbers are quality Water Ace parts.

General Materials

•One Jet Tank System #R-30-T7. Includes: 1/3 HP

jet pump mounted on a 7-gallon diaphragm pressure

tank, pressure gauge, and twin ejector with gasket,

bolts, venturi tubes, and foot valve.

•One can PVC cement (read instructions carefully)

•One can thread compound (read instructions carefully)

•Two male 1-1/4" PVC adapters

•Enough rigid 1-1/4" PVC pipe and couplings to reach

from bottom of well to pump.

•One 4" well seal #RWS4-1012 with vent plug

•One 1-1/4" PVC elbow

Tools Needed for all pump installations

Pipe wrench, pipe clamp, crescent wrench, slot screw-

driver, 24-tooth hacksaw, knife or round file.

PIPING

Plastic PVC pipe is shown in the illustrations, but

galvanized steel pipe may be used if desired. All piping

must be clean and free of all foreign matter to prevent

clogging. ALL JOINTS AND CONNECTIONS IN THE

WELL ASSEMBLY MUST BE AIRTIGHT. Even a pin-

hole leak will prevent the proper operation of the pump

(this is the most common problem). Use thread com-

pound on all threaded joints unless specified otherwise.

DRAINING FOR SERVICING OR FOR WINTER

The pump should be drained before it is disconnected

for servicing or if it is in danger of freezing. To drain:

• Remove drain plug from bottom of pump case.

• Remove discharge tee to vent the pump.

• Drain all piping to a point 3 feet below ground level.

PVC

PIPE

SECTION

FOOT

VALVE

23833A343

STEP

4Remove pipe clamp and

slide Well Seal #RWS4-12

over PVC pipe and onto well

casing. Position assembly

so twelve inches of PVC pipe pro-

trude from well seal. Alternately turn

bolts on well seal counterclockwise

until rubber gaskets are tight against

well casing and PVC pipe.

APPROX.

12" OF

PVC PIPE

PROTRUDING

FROM WELL

SEAL

WELL

SEAL

#RWS4-12

of PVC pipe before cementing

elbow. Smooth inside of any cut

PVC pipe with file or knife.

STEP

5Cement 1-1/4" PVC elbow

onto PVC pipe protruding

from well seal. If desired,

some length may be cut off

1-1/4"

PVC

ELBOW

TOP OF

PVC PIPE

PROTRUDING

FROM WELL

SEAL

STEP

9Place a large bucket

beneath the pressure

regulator outlet. Start

motor. Turn regulator

(part #25881A281 stamped on the side) into larger hole

until snug. Put gasket over venturi tube so openings in

gasket line up with openings in ejector.

STEP

6Open ejector

pack included

with your jet sys-

tem. The ejector

has two holes in its top.

Thread the venturi tube

GASKET VENTURI

TUBE EJECTOR BOLTS

STEP

7Secure ejector and

gasket to front of tank-

mounted pump with

bolts provided. Thread

a 1-1/14" male PVC

adapter into front of

ejector.

Cement as much PVC pipe and couplings

needed to connect PVC elbow to male PVC

adapter in front of ejector. The diaphragm

pressure tank is preset to 30 PSI. Reset

STEP

pressure to 18 PSI using a tire gauge. This is vital to

proper operation of the system.

MALE PVC

ADAPTER

EJECTOR

PRESSURE

GAUGE

ADJUSTMENT

PRESSURE

REGULATOR

adjustment screw down tight.

If pump is properly primed a

high pressure will immediately

show on the pressure gauge.

With pump operating at high

pressure, slowly unscrew reg-

ulator adjustment screw until

maximum water flow is obtained without

pressure dropping to zero. If pressure falls

completely, retighten adjustment screw and

read-just. Steady pressure must not be less

than 24 lbs. for the R520. If no pressure shows:

Stop motor, remove pressure gauge plug from pressure

regulator, add more water, and try again.

STEP

Thread pressure

gauge plug back

into discharge

tee. Thread

pressure gauge into pres-

sure gauge plug. Make

sure all connections are

tightly sealed. Place a

large basin beneath dia-

phragm tank outlet. Start

motor. If pump is off-set

from well 4 feet or more, it

may take a few minutes

for pump to prime. Failure to prime in 5 minutes:

Stop motor, remove pressure gauge plug from dis-

charge tee, add more water, try again. Allow pump to

run long enough to clear the well of sand or dirt and to

insure well will not run dry. Stop motor.

STEP 9

CONT'D

Connect the 1" tank outlet to the service line.

Total installation should look like the drawing

below.

STEP

COMPLETE

SHALLOW WELL

INSTALLATION

23833A343

DEEP WELL PUMP INSTALLATION

(4" DIAMETER CASED WELL)

For wells over 25, but not exceeding 60 feet in depth,

the twin ejector must be installed down inside the well

rather than attached to the front of the pump. Materials

with part numbers are quality Water Ace parts.

General Materials

•One Jet Tank System #R-30-T7. Includes: 1/3 HP

jet pump mounted on a 7-gallon diaphragm pressure

tank, pressure gauge, and twin ejector with

gasket, bolts, venturi tubes, and foot valve.

•One can PVC cement (read instructions carefully)

•One can thread compound (read instructions carefully)

•One 1-1/4" close nipple

•One 1" x 4" nipple

• One 1-1/4" x 5" nipple

•Two 1" female PVC adapters

•One 1" male PVC adapter

•Two 1-1/4" male PVC adapters

•Enough rigid 1-1/4" PVC pipe and couplings to reach

from bottom of well to pump (delivery pipe)

•Enough rigid 1" PVC pipe and couplings to reach

from bottom of well to pump (pressure pipe))

•One well seal #RWS4-1012

•One 1-1/4" PVC elbow

•One 1" PVC elbow

REMINDER: ALL JOINTS AND CONNECTIONS MUST BE AIRTIGHT. A SINGLE PIN-

HOLE LEAK WILL PREVENT THE PROPER OPERATION OF THE PUMP. USE THREAD

COMPOUND ON ALL THREADED CONNECTIONS UNLESS SPECIFIED OTHERWISE.

1-1/4"

NIPPLE

STEP

1Thread 1-1/4" close nipple

into foot valve. Thread the

other end of 1-1/4" close

nipple into bottom of twin

ejector. Hand tighten, then

tighten 1/4 turn with pipe

wrench.

STEP

larger hole until snug. Thread 1" x

5" nipple into smaller hole. Only

hand tighten venturi tube. Tighten

nipple 1/4 turn with pipe wrench.

The ejector has two holes in

the top of it. Thread venturi

tube (part #25881A281

stamped on the side) into

EJECTOR

FOOT

VALVE

EJECTOR

VENTURI

TUBE

1" X 5"

NIPPLE

Thread a 1-1/4" male PVC

adapter over the venturi

tube and into ejector.

Thread a 1" female PVC

adapter onto 1" x 5" nipple.

Tighten adapters 1/4 turn

with crescent wrench.

STEP

1" FEMALE

PVC

ADAPTER 1-1/4" MALE

PVC

ADAPTER

Subtract five feet from the

depth of your well. This is

the total length of PVC pipe

and couplings to cement

onto both the 1-1/4" male and 1"

female PVC adapters. Cement a

section of PVC pipe to each adapter.

STEP

41-1/4"

PVC

PIPE

PVC

PIPE

STEP

5Lower the assembly into

the well, foot valve first.

Use a pipe clamp to

prevent assembly for

sliding down into well.

Cement as many

couplings and sections

of rigid PVC pipe on

both sides of ejector as

it takes to equal the

depth of your well minus

five feet, then firmly

clamp assembly with a

pipe clamp to prevent it

from sliding down into

the well.

STEP

6Remove pipe clamp and

slide well seal

#RWS4-1012

over PVC pipes and onto

well casing. DO NOT let

assembly slide down into well. Posi-

tion assembly so that twelve inches

of PVC pipes protrude from well

seal. Using crescent wrench, turn

bolts on well seal counterclockwise

until rubber gaskets are tight against

the well casing and the PVC pipes.

12" OF

PVC PIPE

PROTRUD-

ING FROM

WELL

SEAL

WELL SEAL

#RWS4-1212

23833A343

STEP

8Thread 1-1/4" male PVC

adapter into top hole in front

of tank-mounted pump.

Thread 1" x 4" nipple into

bottom hole in front of pump.

1-1/4" PVC

ELBOW

1" PVC

ELBOW

STEP

7Cut 1" pipe 2" shorter than

the 1-1/4" pipe. Smooth

rough edges. Cement 1"

and 1-1/4" PVC elbows to

pipes protruding from the

well seal.

1" PIPE 2"

SHORTER

THAN 1-1/4"

PIPE

STEP

9Thread the 1" female PVC

adapter onto the 1" x 4"

nipple.

STEP

Cement as

many sec-

tions and

couplings of

rigid 1" and

1-1/4" PVC pipe needed to connect the 1" female PVC

adapter and the 1-1/4" male PVC adapter to the 1" and

1-1/4" PVC elbows. The diaphragm pressure tank is

factory preset to 30 PSI. Reset the pressure to 18

PSI using a tire gauge. This is vital to the proper

operation of the system. Remove pressure gauge plug.

1" PVC PIPE

1 1/4" PVC PIPE

STEP

COMPLETE

DEEP WELL

INSTALLATION

CAUTION: If you change pressure switch settings,

set the cut-off pressure low enough to shut off the

pump. The recommended pressure is 2 PSI below

your pump cut-off pressure. Example: if a 20-40 PSI

pressure switch is being used, tank pressure should

be 18 PSI. If a valve shuts off and the cut-off setting

is too high, the pump will run continuously without

water flow causing overheating and serious damage.

ed without pressure dropping to zero. If pressure falls

completely, retighten adjustment screw and re-adjust.

Steady pressure must not be less than 24 lbs. for the

R520 and 32 lbs. for the R100. If no pressure shows:

Stop motor, remove pressure gauge plug from pressure

regulator, add more water, and try again. Complete

installation should look like the drawing to the right.

Place a large bucket

beneath the pressure

regulator outlet. Start

motor. Turn regulator

adjustment screw down tight.

If pump is properly primed a

high pressure will immediately

show on the pressure gauge.

With pump operating at high

pressure, slowly unscrew reg-

ulator adjustment screw until

maximum water flow is obtain-

1 1/4" MALE

PVC

ADAPTER

1" x 4"

NIPPLE

1 1/4"

FEMALE

PVC

ADAPTER

REGULATOR

ADJUSTMENT

SCREW

23833A343

PROBLEM POSSIBLE CAUSES

Pump will not prime

•Not enough water. Stop motor, remove pressure gauge plug, and fill case with water.

•Pump wired incorrectly.

•Plugged venturi tube or nozzle.

•Foot valve is sitting in sand or mud, or is stuck shut, or leaks.

•Low well water level. In deep wells, the ejector as well as the foot valve must be below

water level.

•Leaks. Check all connections for airtightness.

TROUBLESHOOTING CHECKLIST (CAUTION: SHUT OFF POWER TO PUMP)

•Low well water level. Use a water-level tester while pump is operating.

•Plugged venturi tube, nozzle, or impeller parts.

Pump delivers water

for a period of time,

then stops pumping

•Plugged venturi or nozzle.

•Faulty pressure gauge resulting in false readings.

•In deep wells, the operating pressure may be too high.

•Low well water level. Use a water-level tester while pump is operating.

•Over-submergence of ejector. In deep wells, if ejector is more than 10 feet below

pumping level, pumping capacity is reduced.

•In deep wells, the ejector may have improper size and depth setting.

Motor overheats and

shuts off (overload)

•Motor voltage does not match power supply voltage. See pages 2 and 3.

•Improper wire size. See Wire Size Guide on page 3.

•Impeller is rubbing against pump case.

•Impeller neck is worn.

•Defective pressure switch.

•The tube connecting the two brass fittings may be clogged.

•Tank precharge pressure too high. Tank precharge pressure must be 1-2 pounds less

than switch turn-on setting.

•In deep wells, the water level may be going below limit of ejector. Use water-level

tester while pump is operating.

•Galvanized storage tank is waterlogged.

•Leaky foot valve.

•Too much tank pressure.

Pressure switch

turns on and off

every few seconds

Motor fails or does

not operate properly •If within Warranty, return pump/motor unit to place of purchase (with proof of purchase)

for exchange.

Pump delivers water

but will not shut off

Pump does not de-

liver rated capacity

Water Ace Pump Co. • 1101 Myers Parkway • Ashland, Ohio 44805-1969 7/95

LIMITED WARRANTY

WATER ACE PUMP CO. will repair or replace for the original user any portion of a new

Water Ace product which proves defective due to materials or workmanship of WATER ACE

PUMP CO. Contact the nearest authorized WATER ACE PUMP CO. dealer for warranty

service. WATER ACE PUMP CO. shall possess the sole right to determine whether to repair

or replace defective equipment, parts or components. THIS WARRANTY DOES NOT

COVER DAMAGE DUE TO LIGHTNING OR OTHER CONDITIONS BEYOND THE

CONTROL OF WATER ACE PUMP CO.

PUMPS: Warranted 12 months from date of purchase or 18 months from date of

manufacture, whichever occurs first. Receipt and product date code required for warranty

claim.

LABOR & COSTS: WATER ACE PUMP CO. shall IN NO EVENT be liable for the cost of

field labor or other charges incurred by any customer in removing and/or reaffixing any

WATER ACE PUMP product. part or component.

THIS WARRANTY WILL NOT APPLY: (a) to defects or malfunctions resulting from failure to

properly install, operate, or maintain the unit in accordance with printed instructions provided;

(b) to failures resulting from abuse, accident, or negligence; (c) to normal maintenance

services and the parts used in connection with such service; (d) to units which are not

installed in accordance with applicable local codes, ordinances, and good trade practices; (e)

if the unit is moved from its original installation location; (f) if unit is used for purposes other

than for what it was designed and manufactured.

PRODUCT IMPROVEMENTS: WATER ACE PUMP CO. reserves the right to change or

improve its products or any component without obligation to provide such a change or

improvement for units previously sold and/or shipped.

WARRANTY EXCLUSIONS: After the expiration of this warranty period, THERE WILL BE

NO WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR ANY PARTICULAR PURPOSE ON ANY SPECIFIC WATER ACE PUMP

PRODUCT. Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you. No warranties or representations at any time

made by any representative of WATER ACE PUMP CO. shall vary or expand the provisions

hereof.

LIABILITY LIMITATION: IN NO EVENT SHALL WATER ACE PUMP CO. BE LIABLE FOR

CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR

RELATED IN ANY MANNER TO ANY WATER ACE PUMP PRODUCT OR PARTS. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation may not apply to you. This Warranty gives you specific legal rights. You

may have other rights which vary from state to state. In the absence of suitable proof of

purchase date, the effective date of this warranty will be based upon the date of manufacture

plus 180 days.

Direct all Notices, etc. to:

Product Warranty and Return Dept., WATER ACE PUMP CO., 1101

Myers Parkway, Ashland, OH 44805-1969

REPLACEMENT PARTS

REF.

NO. REF.

NO.

24859C500

19101A019

14740A001

15760A510

19277A001

19100A029

19109A012

23188A002

25579A108

08728A006

25881A281

23188A001

20929D501

05003A000

24349B000

23188A005

05004A015

05004A087

05126A013

05916A171

05920A173

06190A001

25800A500

10649A120

11933A002

PART NUMBER PART NUMBER

DESCRIPTION DESCRIPTION

EJECTOR BODY

SCREW (2 required)

HOSE CLAMP (2 required)

REGULATOR SWITCH

GASKET

SCREW (2 required)

NUT (2 required)

FITTING

EMBLEM

NOZZLE

VENTURI TUBE

FITTING

PUMP

PRESSURE GAUGE

REGULATOR

HOSE ADAPTER

BUSHING

PIPE TEE

PIPE NIPPLE

HOSE

T.O.E. NIPPLE

TANK

TUBE

SHIM (2 required)

JET TANK SYSTEM

MODEL R-30-T7

Water Ace Pump Co. • 1101 Myers Parkway • Ashland, OH 44805

23833A343 7/95

13, 19, 20

112 2 325 4

23833A343

REVISION TO PARTS LIST

If a 3/4" x 3/4" regulator is used, follow the replacement parts

list found in the jet tank system installation manual. If a 1" x 1" regulator is used, the following parts will be

different than the parts list found in the jet tank system

installation manual.

3/4" Regulator

3/4" x 1" Elbow

3/4" x 1/4" Reducer Bushing

3/4" x 1" Reducer Bushing

3/4" x 3" Nipple

1/4" Barbed Fitting

Ref.

No.

25443A000

05762A055

05004A016

05004A087

05916A191

23188A002

Part Number Description

25443A001

05762A009

05004A035

—

05427A250

23188A001

Description

1" Regulator

1" Elbow

1" x 1/4" Reducer Bushing

Not Required

1" x 3-1/2" Nipple

1/8"" Barbed Fitting

Replaced by

Part Number

Retain these instructions for future reference.

7/95

Water Ace Pump Co. • 1101 Myers Parkway • Ashland, OH 44805

Ace Hardware Jet Tank System R 30 T7 Users Manual 23833A343 R30

R-30-T7 to the manual 8e1d3ca7-a257-4990-b2ba-b246769da75f

Navigation menu

Versions of this User Manual:

Views

Navigation