Acer orporated RTL8191SE 802.11b/g/n RTL8191SE miniCard User Manual OEM installation guide

Download:
Mirror Download [FCC.gov]
Document ID	1248573
Application ID	UZl0c5VK1a33/Y4jsdsWGA==
Document Description	OEM installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.58kB (719722 bits)
Date Submitted	2010-03-04 00:00:00
Date Available	2010-03-04 00:00:00
Creation Date	2010-03-02 14:02:10
Producing Software	Adobe Acrobat 9.3 Image Conversion Plug-in
Document Lastmod	2010-03-02 14:06:05
Document Title	OEM installation guide
Document Creator	Adobe Acrobat 9.3

OE/l/l Installation Guide
RTL8191SE
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used In accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
0 Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is
not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter.
FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be professionally installed to
ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to
ensure that only certified systems are deployed in the United States. The use of the system in any other combination
(such as co—Iocated antennas transmitting the same information) is expressly forbidden.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 200m between the radiator & your body.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the FCC
radio—frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be
informed that any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
The FCC part 15.19 statement below has to also be available in the manual:
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Wireless LAN Network Interface Controller
OEM Installation Guide RTL3191SE
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: HLZ-RTL8191SE
IC Statement
Country Code Statement
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is
not possible.
This device and its antenna(s) must not be co-Iocated or operation in conjunction with any other antenna or
transmitter.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r. p) is not more than that permitted for successful communication.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS—102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC:1754F —RTL81 91SE
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance
requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module
is integrated into. Under such configuration, the IC RSS—102 radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate
this equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B conforme a la norme NMB—003 du Canada.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Wireless LAN Network Interface Controller

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2010:03:02 14:02:10+08:00
Creator                         : Adobe Acrobat 9.3
Modify Date                     : 2010:03:02 14:06:05+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2010:03:02 14:06:05+08:00
Creator Tool                    : Adobe Acrobat 9.3
Format                          : application/pdf
Document ID                     : uuid:b06348f8-b42c-43f1-8625-fe843a6e8cd3
Instance ID                     : uuid:2ad76f60-6f68-444b-8b91-32a490b8064b
Producer                        : Adobe Acrobat 9.3 Image Conversion Plug-in
Page Count                      : 2

EXIF Metadata provided by EXIF.tools