Acer orporated UWA3 USB Wireless Adapter User Manual WL 7200 V1 QSG User Manual 319 v1 1

Acer Incorporated USB Wireless Adapter WL 7200 V1 QSG User Manual 319 v1 1

User Manual.pdf

INFORMATION TO USER Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.* Consult the dealer or an experienced radio/TV technician for help. REGULATION INFORMATION The WLAN USB Wireless Adapter must be installed and used in strict accordance with the manufacturer’s instructions. This device complies with the following radio frequency and safety standards.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To comply with the FCC RF exposure compliance requirements, this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.The use of the USB adapter with laptops/notebooks is prohibited . FOR MOBILE DEVICE USAGE (>20cm/low power eg. AP routers) Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body .
˦̇˴̇˸̀˸́̇ˍ˦̇˴̇˸̀˸́̇ˍ˦̇˴̇˸̀˸́̇ˍ˦̇˴̇˸̀˸́̇ˍʳʳʳʳʳʳ˙˖˖ʳ˜˗ʳˍʳ˦˨˭ˀˣ˕˅ˊ˃˄ʳ˙˖˖˙˖˖˙˖˖˙˖˖ʳ˧˻˼̆ʳ˷˸̉˼˶˸ʳ˶̂̀̃˿˼˸̆ʳ̊˼̇˻ʳ̃˴̅̇ʳ˄ˈʳ̂˹ʳ̇˻˸ʳ˙˖˖ʳ˥̈˿˸̆ˁʳˢ̃˸̅˴̇˼̂́ʳ˼̆ʳ̆̈˵˽˸˶̇ʳ̇̂ʳ̇˻˸ʳ˹̂˿˿̂̊˼́˺ʳ̇̊̂ʳ˶̂́˷˼̇˼̂́̆ˍʳ ʳʻ˄ʼʳ˧˻˼̆ʳ˷˸̉˼˶˸ʳ̀˴̌ʳ́̂̇ʳ˶˴̈̆˸ʳ˻˴̅̀˹̈˿ʳ˼́̇˸̅˹˸̅˸́˶˸ʳʻ˅ʼʳ̇˻˼̆ʳ˷˸̉˼˶˸ʳ̀̈̆̇ʳ˴˶˶˸̃̇ʳ˴́̌ʳ˼́̇˸̅˹˸̅˸́˶˸ʳ̅˸˶˸˼̉˸˷ʿʳ˼́˶˿̈˷˼́˺ʳ˼́̇˸̅˹˸̅˸́˶˸ʳ̇˻˴̇ʳ̀˴̌ʳ˶˴̈̆˸ʳ̈́˷˸̆˼̅˸˷ʳ̂̃˸̅˴̇˼̂́ʳ̂˹ʳ̇˻˸ʳ˷˸̉˼˶˸ˁʳ˧˻˼̆ʳ˸̄̈˼̃̀˸́̇ʳ˻˴̆ʳ˵˸˸́ʳ̇˸̆̇˸˷ʳ˴́˷ʳ˹̂̈́˷ʳ̇̂ʳ˶̂̀̃˿̌ʳ̊˼̇˻ʳ̇˻˸ʳ˿˼̀˼̇̆ʳ˹̂̅ʳ˴ʳ˖˿˴̆̆ʳ˕ʳ˷˼˺˼̇˴˿ʳ˷˸̉˼˶˸ʿʳ̃̈̅̆̈˴́̇ʳ̇̂ʳ̃˴̅̇ʳ˄ˈʳ̂˹ʳ̇˻˸ʳ˙˖˖ʳ̅̈˿˸̆ˁʳ˧˻˸̆˸ʳ˿˼̀˼̇̆ʳ˴̅˸ʳ˷˸̆˼˺́˸˷ʳ̇̂ʳ̃̅̂̉˼˷˸ʳ̅˸˴̆̂́˴˵˿˸ʳ̃̅̂̇˸˶̇˼̂́ʳ˴˺˴˼́̆̇ʳ˻˴̅̀˹̈˿ʳ˼́̇˸̅˹˸̅˸́˶˸ʳ˼́ʳ˴ʳ̅˸̆˼˷˸́̇˼˴˿ʳ˼́̆̇˴˿˿˴̇˼̂́ˁʳ˧˻˼̆ʳ˸̄̈˼̃̀˸́̇ʳ˺˸́˸̅˴̇˸̆ʿʳ̈̆˸̆ʳ˴́˷ʳ˶˴́ʳ̅˴˷˼˴̇˸ʳ̅˴˷˼̂ʳ˹̅˸̄̈˸́˶̌ʳ˸́˸̅˺̌ʳ˴́˷ʿʳ˼˹ʳ́̂̇ʳ˼́̆̇˴˿˿˸˷ʳ˴́˷ʳ̈̆˸˷ʳ˼́ʳ˴˶˶̂̅˷˴́˶˸ʳ̊˼̇˻ʳ̇˻˸ʳ˼́̆̇̅̈˶̇˼̂́̆ʿʳ̀˴̌ʳ˶˴̈̆˸ʳ˻˴̅̀˹̈˿ʳ˼́̇˸̅˹˸̅˸́˶˸ʳ̇̂ʳ̅˴˷˼̂ʳ˶̂̀̀̈́˼˶˴̇˼̂́̆ʳʳʳʳʳ˜˖ʳˍʳˈˌ˅ˆ˔ˀˣ˕˅ˊ˃˄ʳ˜˖˜˖˜˖˜˖ʳThis Class B digital apparatus complies with Canadian ICES-003 and RSS210ʳ˧˻˼̆ʳ˷˸̉˼˶˸ʳ˶̂̀̃˿˼˸̆ʳ̊˼̇˻ʳ˜́˷̈̆̇̅̌ʳ˖˴́˴˷˴ʳ˿˼˶˸́˶˸ˀ˸̋˸̀̃̇ʳ˥˦˦ʳ̆̇˴́˷˴̅˷ʻ̆ʼˁʳˢ̃˸̅˴̇˼̂́ʳ˼̆ʳ̆̈˵˽˸˶̇̇̂ʳ̇˻˸ʳ˹̂˿˿̂̊˼́˺ʳ̇̊̂ʳ˶̂́˷˼̇˼̂́̆ˍʳʻ˄ʼʳ̇˻˼̆ʳ˷˸̉˼˶˸ʳ̀˴̌ʳ́̂̇ʳ˶˴̈̆˸ʳ˼́̇˸̅˹˸̅˸́˶˸ʿʳ˴́˷ʳʻ˅ʼʳ̇˻˼̆ʳ˷˸̉˼˶˸ʳ̀̈̆̇ʳ˴˶˶˸̃̇ʳ˴́̌ʳ˼́̇˸̅˹˸̅˸́˶˸ʿʳ˼́˶˿̈˷˼́˺ʳ˼́̇˸̅˹˸̅˸́˶˸ʳ̇˻˴̇ʳ̀˴̌ʳ˶˴̈̆˸ʳ̈́˷˸̆˼̅˸˷ʳ̂̃˸̅˴̇˼̂́ʳ̂˹ʳ̇˻˸ʳ˷˸̉˼˶˸ˁʳʳʳ˖˴́˴˷˴ʿʳ˴̉˼̆ʳ˷ϗ˜́˷̈̆̇̅̌ʳ˖˴́˴˷˴ʳʻ˜˖ʼˍʳ˖˸̇ʳ˴̃̃˴̅˸˼˿ʳ́̈̀ͼ̅˼̄̈˸ʳ˷˸ʳ˶˿˴̆̆˸ʳ˕ʳ˸̆̇ʳ˶̂́˹̂̅̀˸ʳ˴̈̋ʳ́̂̅̀˸̆ʳ˶˴́˴˷˼˸́́˸̆ʳ˜˖˘˦ˀ˃˃ˆʳ˸̇ʳ˥˦˦ˀ˅˄˃ˁ˦̂́ʳ˹̂́˶̇˼̂́́˸̀˸́̇ʳ˸̆̇ʳ̆̂̈̀˼̆ʳ˴̈̋ʳ˷˸̈̋ʳ˶̂́˷˼̇˼̂́̆ʳ̆̈˼̉˴́̇˸̆ʳˍʳʻ˄ʼʳ˶˸̇ʳ˴̃̃˴̅˸˼˿ʳ́˸ʳ˷̂˼̇ʳ̃˴̆ʳ˶˴̈̆˸̅ʳ˷ʺ˼́̇˸̅˹ͼ̅˸́˶˸̆ʳ˸̇ʳʻ˅ʼʳ˶˸̇ʳ˴̃̃˴̅˸˼˿ʳ˷̂˼̇ʳ˴˶˶˸̃̇˸̅ʳ̇̂̈̇˸ʳ˼́̇˸̅˹ͼ̅˸́˶˸ʿʳ́̂̇˴̀̀˸́̇ʳ˿˸̆ʳ˼́̇˸̅˹ͼ̅˸́˶˸̆ʳ̄̈˼ʳ̃˸̈̉˸́̇ʳ˴˹˹˸˶̇˸̅ʳ̆̂́ʳ˹̂́˶̇˼̂́́˸̀˸́̇ˁʳ Complies with IDA Standards DA 104808FCC ID : SUZ-UWA2 IC ID : 5923A-UWA2 FCC ID: HLZUWA3IC: 1754F-UWA3
Europe- R&TTE Compliance Statement Hereby, the company who declares that this equipment complies with the essential requirements and other relevant provisions of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). CE Declaration of Conformity For the following equipment: USB WiFi adapter(Product Name) USB WiFi Adapter(Model Designation) UWA2is herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/EC). For the evaluation regarding this Directive, the following standards were applied: EN 300 328 V1.7.1 EN 301 489-1 V1.6.1 ; EN 301 489-17 V1.2.1 EN 60950-1:2001 This equipment is marked with the symbol and can be used throughout the European community. Marking by the symbol indicates that usage restrictions apply. France - 2.4GHz for Metropolitan France: In all Metropolitan départements, wireless LAN frequencies can be used under the following conditions, either for public or private use: ͊Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band͊Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device is intended for use as check in the following European Community countries: Austria Belgium Czech Republic CyprusDenmark Estonia France Finland Germany Greece Hungary Ireland Italy Iceland Luxemburg LatviaLithuania Malta Norway Netherlands Portugal Poland Spain Sweden Slovakia Slovenia United Kingdom
܅פ෷ሽंᘿ୴ࢤሽᖲጥ෻ᙄऄ܅פ෷୴᙮ሽᖲᤞ፿ᑑقփ୲Κψ)2*ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔ!ॺᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌشृ݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ෷ࢨ᧢ޓ଺!๻ૠհ௽ࢤ֗פ౨Ζ)3*܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫ!ٽऄຏॾΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀޏ࿳۟ྤեឫழֱ൓ᤉ!ᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄ๵ࡳ܂ᄐհྤᒵሽຏॾΖ܅פ෷୴᙮!ሽᖲႊݴ࠹ٽऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ๻ໂհեឫΖ!
The channel identifiers, channel center frequencies, and regulatory domains of each 22-MHz-wide channel are shown in following Table. &KDQQHO,GHQWLILHU)UHTXHQF\0+=5HJXODWRU\'RPDLQV-DSDQ (76, 1RUWK$PHULFD ,VUDHO 0H[LFR ˗˗˗  ˗˗˗  ˗˗˗˗ ˗˗˗˗ ˗˗˗˗ ˗˗˗˗ ˗˗˗˗ ˗˗˗˗ ˗˗˗˗ ˗˗˗ ˗ ˗˗˗ ˗ ˗˗  ˗˗  ˗


14 0RGHO1DPH :/93URGXFW1DPH :/$1Q86%$GDSWHU6WDQGDUG EJQ'DWD7UDQVIHU5DWH DQGPD[LPXPRI0ESV0RGXODWLRQ0HWKRG %36.436.4$04$0'%36.'436.&&.)UHTXHQF\%DQG *+],60%DQG6SUHDG6SHFWUXP ,(((E'666'LUHFW6HTXHQFH6SUHDG6SHFWUXP,(((JQ2)'02UWKRJRQDO)UHTXHQF\'LYLVLRQ0XOWLSOH[LQJ5)2XWSXW3RZHUWROHU DQ FHG%PG%P#QG%P#JG%P#E2SHUDWLRQ0RGH $GKRF,QIUDVWUXFWXUH5HFHLYHU6HQV LWLYLW\ 0ESVG%P#0ESVG%P#0ESVG%P#2SHUDWLRQ5DQJH ,QGRRUXSWRPHWHUV2XWGRRUXSWRPHWHUV/(' 3RZHU266XSSRUW :LQGRZV;39LVWD0DF/LQX[6HFXULW\ ELWELW:(37.,3$(6:3$:3$,QWHUIDFH 86%3RZHU&RQVXPSWLRQ 7UDQVPLWDURXQGP$5HFHLYHDURXQGP$2SHUDWLQJ7HPSHUDWXUH ²&DPELHQWWHPSHUDWXUH6WRUDJH7HPSHUDWXUH a&DPELHQWWHPSHUDWXUH+XPL GLW\ WRPD[LPXPQRQFRQGHQVLQJ'LPHQVLRQ [[PP/[:[+USB Wireless Adapter UWA3
15 Symptom :The LED is off. Remedy :Make sure the dongle is inserted properly. Otherwise contact your vendor. Symptom :The LED is always on not blinking. Remedy :Make sure that you have installed the driver from attached CD. Otherwise contact your vendor. Symptom :The LED is blinking but the icon does not appear in your icon tray. Remedy :Make sure that you have installed the Utility from the attached CD. Symptom :The dongle is linking, but can’t share files with others. Remedy :Make sure the file and printer sharing function is enabled. You can enable the function by checking the icon of My Computer -> ControlPanel -> Network -> file and printer sharing -> I want to be able to give others to access to my files. Symptom :Slow or poor performance under AP mode Remedy :Try to select another channel for the communicating group or move your device closer to the Access Point.
16 IEEE 802.11 StandardThe IEEE 802.11 Wireless LAN standards subcommittee, which is formulating DVWDQGDUGIRUWKHLQGXVWU\Access PointAn internetworking device that seamlessly connects wired and wireless networks together. Ad HocAn Ad Hoc wireless LAN is a group of personal computers, each with a WLAN adapter, connected as an independent wireless LAN. Ad Hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation. BSSIDA specific Ad Hoc LAN is called a Basic Service Set (BSS). Personal computers in a BSS must be configured with the same BSSID. DHCPDynamic Host Configuration Protocol - a method in which IP addresses are assigned by server dynamically to clients on the network. DHCP is used for Dynamic IP Addressing and requires a dedicated DHCP server on the network. Direct Sequence Spread SpectrumThis is the method the wireless cards use to transmit data over the frequency spectrum. The other method is frequency hopping. Direct sequence spreads the data over one frequency range (channel) while frequency hopping jumps from one narrow frequency band to another many times per second. ESSIDAn Infrastructure configuration could also support roaming capability for mobile workers. More than one BSS can be configured as an Extended Service Set (ESS). Users within an ESS could roam freely between BSSs while served as a continuous connection to the network wireless stations and Access Points within an ESS must be configured with the same ESSID and the same radio channel. EthernetEthernet is a 10/100Mbps network that runs over dedicated home/office wiring. Users must be wired to the network at all times to gain access. GatewayA gateway is a hardware and software device that connects two dissimilar
17 systems, such as a LAN and a mainframe. In Internet terminology, a gateway is another name for a router. Generally a gateway is used as a funnel for all traffic to the Internet. IEEEInstitute of Electrical and Electronics Engineers Infrastructure An integrated wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers. ISM BandThe FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the so-called ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. Local Area Network (LAN)A LAN is a group of personal computers, each equipped with the appropriate network adapter card connected by cable/air, that share applications, data, and peripherals. All connections are made via cable or wireless media, but a LAN does not use telephone services. It typically spans a single building or campus. NetworkA network is a system of personal computers that is connected. Data, files, and messages can be transmitted over this network. Networks may be local or wide area networks. ProtocolA protocol is a standardized set of rules that specify how a conversation is to take place, including the format, timing, sequencing and/ or error checking. SSIDA Network ID unique to a network. Only clients and Access Points that share the same SSID are able to communicate with each other. This string is case-sensitive. Static IP AddressingA method of assigning IP addresses to clients on the network. In networks with Static IP address, the network administrator manually assigns an IP address to each personal computer. Once a Static IP address is assigned, a personal computer
18 uses the same IP address every time it reboots and logs on to the network, unless it is manually changed. Temporal Key Integrity Protocol (TKIP)The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard for wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP. Transmission Control Protocol / Internet Protocol (TCP/IP)TCP/IP is the protocol suite developed by the Advanced Research Projects Agency (ARPA). It is widely used in corporate Internet works, because of its superior design for WANs. TCP governs how packet is sequenced for transmission the network. The term “TCP/IP” is often used generically to refer to the entire suite of related protocols. Transmit / ReceiveThe wireless throughput in Bytes per second averaged over two seconds. Wi-Fi AllianceThe Wi-Fi Alliance is a nonprofit international association formed in 1999 to certify interoperability of wireless Local Area Network products based on IEEE 802.11 specification. The goal of the Wi-Fi Alliance’s members is to enhance the user experience through product interoperability. The organization is formerly known as WECA. Wi-Fi Protected Access (WPA)The Wi-Fi Alliance put together WPA as a data encryption method for 802.11 wireless LANs. WPA is an industry-supported, pre-standard version of 802.11i utilizing the Temporal Key Integrity Protocol (TKIP), which fixes the problems of WEP, including using dynamic keys. Wide Area Network (WAN)A WAN consists of multiple LANs that are tied together via telephone services and / or fiber optic cabling. WANs may span a city, a state, a country, or even the world. Wired Equivalent Privacy (WEP)Now widely recognized as flawed, WEP was a data encryption method used to protect the transmission between 802.11 wireless clients and APs. However, it used the same key among all communicating devices. WEP’s problems are well-known, including an insufficient key length and no automated method for distributing the keys. WEP can be easily
19 cracked in a couple of hours with off-the-shelf tools. Wireless LAN (WLAN)A wireless LAN does not use cable to transmit signals, but rather uses radio or infrared to transmit packets through the air. Radio Frequency (RF) and infrared are the commonly used types of wireless transmission. Most wireless LANs use spread spectrum technology. It offers limited bandwidth, usually under 11Mbps, and users share the bandwidth with other devices in the spectrum; however, users can operate a spread spectrum device without licensing from the Federal Communications Commission (FCC). Fragment ThresholdThe proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several fragments each of size equal to fragment threshold. By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead. Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible. RTS (Request To Send) ThresholdThe RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission
20 mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance. Beacon IntervalIn addition to data frames that carry information from higher layers, 802.11 includes management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). Preamble TypeThere are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and theshort is 56 bits. WPA2It is the second generation of WPA. WPA2 is based on the final IEEE 802.11i amendment to the 802.11 standard. Temporal Key Integrity Protocol (TKIP)The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard for wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP.
21 802.1x Authentication802.1x is a framework for authenticated MAC-level access control, defines Extensible Authentication Protocol (EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for dial-up authentication with Point-to-Point Protocol in RFC 2284. Beyond encapsulating EAP packets, the 802.1x standard also defines EAPOL messages that convey the shared key information critical for wireless security. Advanced Encryption Standard (AES)Security issues are a major concern for wireless LANs, AES is the U.S. government’s next-generation cryptography algorithm, which will replace DES and 3DES.
How do I connect to the projector?- Please refer to the manual on the included CD for more details.POWERRESETUSB A1 USB A2USB BBranchez la clé dans un port USB sur le projecteurSchließen Sie das Dongle an einen USB-Port des Projektors anCollegare il trasmettitore ad una porta USB sul proiettoreConecte el dispositivo en el puerto USB del proyectorLigue o adaptador à porta USB do projectorSteek de dongle in een usb-poort van de projectorColokkan dongle ke port USB pada proyektorPřipojte vysílač do portu USB na projektoruPodłącz nadajnik do portu USB projektoraПодсоедините адаптер к порту USB на проектореHarici aygıtı, projektördeki bir USB bağlantı noktasına takınΣυνδέστε τον πομπό σε θύρα USB του προβολέαCsatlakoztassa a háttértároló eszközt a projektor USB portjábaZapojte adaptér do portu USB na projektorePlugg donglen inn i en USB-port på projektorenSæt dongle'n i en USB-port på projektoren 1Plug the dongle UWA3 into a USB port on the projector2Connect your device to projector using Wi-FiLiitä käyttöavain projektorin USB-porttiin Anslut hårdvarunyckeln till en USB-port på projektornВставте заглушку в порт USB на проекторіCắm bộ thu phát vào cổng USB trên máy chiếuUtaknite modul u USB priključak projektoraConectaţi cheia la un port USB al proiectoruluiVstavite ključ v vrata USB na projektorjuВключете ключа в USB порта на проектораPredajnik umetnite u USB priključak na projektoru将发射器插入投影机上的USB端口將傳輸器插入投影機上的USB連接埠プロジェクタのUSB ポートにトランスミッターを接続します동글을 USB 포트에 연결เสียบดองเกิลลงในพอร์ต USB บนโปรเจคเตอร์ﻕﻡ ﺏﺕﻭﺹﻱﻝ ﺝﻩﺍﺯ ﺍﻝﺇﺭﺱﺍﻝ ﺏﻡﻥﻑﺫ USB ﻉﻝﻯ ﺍﻝﻡﺱﻕﺍﻁConnectez votre appareil au projecteur via Wi-FiVerbinden Sie Ihr Gerät über Wi-Fi mit dem ProjektorCollegare il dispositivo al proiettore tramite Wi-FiConecte su dispositivo al proyector a través de Wi-FiLigue o seu dispositivo ao projector através de Wi-FiSluit uw apparaat op de projector aan via wi-fiSambungkan perangkat pada proyektor menggunakan Wi-FiPřipojte zařízení k projektoru pomocí Wi-FiPołącz urządzenie z projektorem przez Wi-FiПодключите ваше устройство к проектору посредством Wi-FiAygıtınızı Wi-Fi kullanarak projektöre bağlayınΣυνδέστε τη συσκευή σας στον προβολέα μέσω Wi-FiCsatlakoztassa a készülékét a projektorhoz WiFi-n keresztülPripojte zariadenie k projektoru pomocou Wi-FiKoble enheten til projektoren ved hjelp av Wi-FiOpret forbindelse fra enheden til projektoren med Wi-FiLiitä laite projektoriin Wi-Fi-yhteydelläAnslut din enhet till projektorn genom att använda Wi-FiПідключіть пристрій до проектора через Wi-FiKết nối thiết bị của bạn với máy chiếu qua mạng Wi-Fi Povežite uređaj sprojektorom pute Wi-Fi vezeConectaţi dispozitivul la proiector prin Wi-FiSvojo napravo priključite na projektor preko brezžičnega omrežjaСвържете устройството към проектора чрез Wi-FiPovežite svoj uređaj sa projektorom koristeći Wi-Fi用Wi-Fi连接设备至投影机使用Wi-Fi將裝置連線至投影機Wi-Fi を使ってデバイスをプロジェクタに接続しますWi-Fi를 사용하여 장치를 프로젝터에 연결เชื่อต่ออุปกรณ์ของคุณเข้ากับโปรเจคเตอร์โดยใช้ Wi-Fiﻕﻡ ﺏﺕﻭﺹﻱﻝ ﺝﻩﺍﺯﻙ ﺏﺍﻝﻡﺱﻕﺍﻁ ﺏﺍﺱﺕﺥﺩﺍﻡ Wi-Fi UWA3
Installez l'application de projection requise par votre appareilInstallieren Sie die Projektionsapplikation, welche von Ihrem Gerät benötigt wirdInstallare l'applicazione di proiezione richiesta dal dispositivoInstale la aplicación de proyección requerida por su dispositivoInstale a aplicação de projecção para o seu dispositivoInstalleer de projectietoepassing die nodig is voor uw apparaatInstal aplikasi proyeksi yang diminta perangkat AndaNainstalujte projekční aplikaci požadovanou vašim zařízenímZainstaluj wymaganą przez urządzenie aplikację do projekcjiУстановите приложение для проецирования, необходимое для вашего устройстваAygıtınızın gerektirdiği projeksiyon uygulamasını yükleyinΕγκαταστήστε την εφαρμογή προβολής που χρειάζεται η συσκευή σαςTelepítse a készüléke által igényelt kivetítő alkalmazástNainštalujte aplikáciu na premietanie vyžadovanú zariadenímInstaller projeksjonsapplikasjonen som enheten kreverInstaller projektionsprogrammer, som krævet af enheden3Install the projection application required by your device4Use the installed App to start projectionAsenna laitteesi vaatima projektiosovellusInstallera det projektionsprogram som krävs av enhetenІнсталюйте задачу проекції на вимогу пристроюCài đặt ứng dụng chiếu như yêu cầu bởi thiết bị của bạnInstalirajte potrebnu aplikaciju za projekciju na uređajuInstalaţi aplicaţia de proiecţie necesară pentru dispozitivul dumneavoastrăNamestite projekcijsko aplikacijo, ki jo zahteva napravaИнсталирайте приложението за проектиране, което се изисква от Вашето устройствоInstalirajte aplikaciju za projekcije koje zahteva vaš uređaj安装设备所需的投影机应用程序安裝裝置所需要的投影應用程式デバイスが必要とする投写アプリケーションをインストールします장치에 필요한 영사 응용 프로그램 설치ติดตั้งแอพพลิเคชั่นการฉายภาพโดยอุปกรณ์ของคุณﻕﻡ ﺏﺕﺙﺏﻱﺕ ﺕﻁﺏﻱﻕ ﺍﻝﺇﺱﻕﺍﻁ ﺍﻝﻡﻁﻝﻭﺏ ﻝﺩﻯ ﺝﻩﺍﺯﻙUtilisez l'appli installée pour démarrer la projectionVerwenden Sie die installierte Applikation, um mit der Projektion zu beginnenUtilizzare l'applicazione installata per avviare la proiezioneUtilice la aplicación instalada para iniciar la proyección.Utilize a aplicação instalada para iniciar a projecçãoGebruik de geïnstalleerde app om de projectie te startenGunakan Aplikasi yang diinstal untuk memulai proyeksiPomocí aplikace zahajte projekciUżyj zainstalowaną aplikację do rozpoczęcia projekcjiНачните проецирование при помощи установленного приложенияProjeksiyonu başlatmak için yüklü uygulamayı kullanınΧρησιμοποιήστε την εγκατεστημένη εφαρμογή για έναρξη της προβολήςHasználja a telepített alkalmazást a vetítés megkezdéséhezPoužite nainštalovanú aplikáciu na spustenie premietaniaBruk den installerte applikasjonen til å starte projeksjonBrug det installerede program til at starte projektionenAloita projektorin käyttö asentamallasi sovelluksellaAnvänd installerad app för att starta projektionenПочинайте робити проекцію з інстальованою задачеюSử dụng ứng dụng vừa cài để bắt đầu chiếuUz pomoć instalirane aplikacije pokrenite projekcijuUtilizaţi aplicaţia instalată pentru a începe proiecţiaNameščeno aplikacijo uporabite za začetek projekcijeИзползвайте инсталираното приложение, за да стартирате проектиранетоPomoću instalirane aplikacije pokrenite projekciju用已安装的应用程序启动投影机使用已安裝的應用程式開始投影インストールしたアプリを使って投写を開始します설치된 응용 프로그램으로 영사 시작ใช้แอพพลิเคชั่นที่ติดตั้งเพื่อเริ่มฉายภาพﺍﺱﺕﺥﺩﻡ ﺍﻝﺕﻁﺏﻱﻕ ﺍﻝﻡﺙﺏﺕ ﻝﺏﺩء ﺍﻝﺇﺱﻕﺍﻁ

Navigation menu