Acer P186HV P196HQVbd Monitor User Guide Manual Operating Instructions To The 348a142c B2bd 424d 846f 7b94112cb6e4

User Manual: Acer P186HV to the manual

Open the PDF directly: View PDF .
Page Count: 23

Download
Open PDF In Browser	View PDF

TABLE OF CONTENTS
Special notes on LCD monitors .................................................. 1
Information for your safety and comfort .................................. 2
Unpacking ................................................................................... 5
Attaching/Removing the base .................................................... 6
Screen position adjustment ........................................................ 6
Connecting the power cord........................................................ 7
Safety precaution ....................................................................... 7
Cleaning your monitor ............................................................... 7
Power saving ............................................................................... 8
DDC .............................................................................................. 8
Connector Pin Assignment ......................................................... 9
Standard Timing Table..................................................................11
Installation.....................................................................................12
User controls..................................................................................13
Troubleshooting............................................................................19

SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.

NOTES

• Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
• Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.

EN-1

Information for your safety and comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.

CAUTION for accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and
located as close to the equipment operator as possible. When you need to disconnect
power to the equipment, be sure to unplug the power cord from the electrical outlet.

Warnings
•
•
•

•

•
•

Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the
product falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable operation of
the product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This product should never
be placed near or over a radiator or heat register, or in a built-in installation
unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into the
product.
To avoid damage of internal components and to prevent battery leakage, do
not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environ ment which
will probably cause unexpected short current or damage rotor devices, HDD,
Optical drive, and even exposure risk from lithium battery pack.

Safe listening
Follow these instructions, suggested by hearing experts,to protect your earing.
•
Gradually increase the volume until you can hear it clearly and comfortably and
without distortion.
•
After setting the volume level, do not increase it afteryour ears adjust.
•
Limit the amount of time listening to music at high volume.
•
Avoid turning up the volume to block out noisy surroundings.
•
Turn the volume down if you can’t hear people speaking near you.

EN-2

Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to qualified
service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need for service
•
the product does not operate normally after following the operating instructions
----------------------------------------------------------------------------------------------------Note: Adjust only those controls that are covered by the operating instructions,
since improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to
normal condition.

LCD Pixel Statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.

Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long
work periods, bad posture, poor work habits, stress, inadequate working conditions,
personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis
or other musculoskeletal disorders. The following symptoms may appear in the hands,
wrists, arms, shoulders, neck or back:
•
numbness, or a burning or tingling sensation
•
aching, soreness or tenderness
•
pain, swelling or throbbing
•
stiffness or tightness
•
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s
health and safety department.
The following section provides tips for more comfortable computer use.

Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,
or raising your sitting height to achieve maximum comfort. Observe the following tips:
•
refrain from staying too long in one fixed posture
•
avoid slouching forward and/or leaning backward
•
stand up and walk around regularly to remove the strain on your leg muscles

EN-3

•
•
•
•

take short rests to relax your neck and shoulders
avoid tensing your muscles or shrugging your shoulders
install the external display, keyboard and mouse properly and within comfort
able reach
if you view your monitor more than your documents, place the display at the
center of your desk to minimize neck strain

Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room
lighting, poorly focused screens, very small typefaces and low-contrast displays could
stress your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
•
Rest your eyes frequently.
•
Give your eyes regular breaks by looking away from the monitor and focusing
on a distant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
Keep your display clean.
•
Keep your head at a higher level than the top edge of the display so your eyes
point downward when looking at the middle of the display.
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced
text readability and graphics clarity.
•
Eliminate glare and reflections by:
• placing your display in such a way that the side faces the window or any light
source
• minimizing room light by using drapes, shades or blinds
• using a task light
• changing the display’s viewing angle
• using a glare-reduction filter
• using a display visor, such as a piece of cardboard extended from the display’s
top front edge
•
Avoid adjusting your display to an awkward viewing angle.
•
Avoid looking at bright light sources, such as open windows, for extended
periods of time.

Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
•
Take short breaks regularly and often.
•
Perform some stretching exercises.
•
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
----------------------------------------------------------------------------------------------------Warning! We do not recommend using the product on a couch or bed. If this is
unavoidable, work for only short periods, take breaks regularly, and do some
stretching exercises.
----------------------------------------------------------------------------------------------------For more information and help in recycling, please visit the following websites:
Worldwide:

http://www.acer-group.com/public/Sustainability/sustainability01.htm
http://www.acer-group.com/public/Sustainability/sustainability04.htm

EN-4

UNPACKING
Please check the following items are present when you unpack the box,
and save the packing materials in case you will need to ship or transport
the monitor in future.
•

LCD Monitor

•

AC Power Cord

•

D-Sub Cable
(Optional)

•

Audio Cable
(Optional)

•

User Manual

EN-5

•

DVI Cable
(Optional)

•

Quick Start Guide

Attaching / Removing the Base
-------------------------------------------------------------------Note: Remove the monitor and monitor base from its packaging.
Carefully place the monitor face-down on a stable surface -- use a
cloth to avoid scratching the screen.
Install:
Align the base with the stand and
push the base towards the top of
the monitor.

Remove:
Depress the release hooks as indicated first before removing the
base and follow the arrow direction
to remove it.

SCREEN POSITION ADJUSTMENT
In oder to optimize the best viewing position, you can adjust the tilt of
the monitor by using both of your hands to hold the edges of the monitor
as shown in the figure below.
The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated by arrow below.

EN-6

CONNECTING THE POWER CORD

• Check first to make sure that the power cord you use is the correct type
required for your area.
• This monitor has a universal power supply that allows operation in either
100/120V AC or 220/240 V AC voltage area. No user-adjustment is required.
• Plug one end of the power cord to the AC Inlet, plug another end to a
proper AC outlet.
• For unit using at 120 V AC:
Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.
• For unit using at 220/240 V AC (outside of U.S.):
Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The
cord set should have the appropriate safety approvals for the country in
which the equipment will be installed.

SAFETY PRECAUTION
•

•
•
•

•
•

Avoid placing the monitor, or any other heavy object, on the power cord
to avoid damage to the cable.
Do not expose the monitor to rain, excessive moisture, or dust.
Do not cover the ventilation slots or openings of the monitor. Always
put the monitor in a place where there is adequate ventilation.
Avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the face of the monitor. Place
the monitor just below eye level.
Handle with care when transporting the monitor.
Refrain from giving shock or scratch to the screen, as screen is fragile.

CLEANING YOUR MONITOR
Please carefully follow the below guidelines when cleaning the monitor.
• Always unplug the monitor before cleaning.
• Use a soft cloth to wipe the screen and cabinet front and sides.

EN-7

Power saving
The monitor will be driven into Power Saving” mode by the control signal
from the display controller, as indicated by the amber-color power LED.
State

LED
Light

Blue

Power Saving
Mode

Amber

The power saving states will be kept until a control signal has been detected
or the keyboard or mouse is activated. The recovery time from Active OFF
state back to ON state is around 3 seconds.

DDC
To make your installation easier, the monitor is able to Plug and Play with
your system if your system also supports DDC protocol. The DDC (Display
Data Channel) is a communication protocol through which the monitor
automatically informs the host system about its capabilities, for example,
supported resolutions and corresponding timing. The monitor supports
DDC2B standard.

EN-8

CONNECTOR PIN ASSIGNMENT

15-Pin Color Display Signal Cable
PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

Red

+5V

Green

10.

Logic Ground

Blue

11.

Monitor Ground

12.

DDC-Serial Data

DDC-return

13.

H-Sync

R-Ground

14.

V-Sync

G-Ground

15.

DDC-Serial Clock

B-Ground

EN-9

24-Pin Color Display Signal Cable*

Meaning

TMDS Data2-

13.

TMDS Data2+

14.

+5V Power

TMDS Data 2/4 Shield

15.

Logic Ground

16.

Hot Plug Detect

17.

TMDS Data0-

DDC Clock

18.

TMDS Data0+

DDC Data

19.

TMDS Data 0/5 Shield

20.

TMDS Data1-

21.

10.

TMDS Data1+

22.

TMDS Clock Shield

11.

TMDS Data 1/3 Shield

23.

TMDS Clock+

12.

24.

DDC TMDS Clock-

EN-10

Standard Timing Table
Mode

Resolution

640x480

MAC

640x480

66.66

VESA

720x400

SVGA

800x600

SVGA

800x600

SVGA

800x600

SVGA

800x600

MAC

832x624

74.55

XGA

1024x768

XGA

1024x768

XGA

1024x768

VESA

1280x720

WXGA

1280x800

WXGA

1366x768

EN-11

INSTALLATION

To install the monitor to your host system, please follow the steps as given
below:
Steps
1. 1-1 Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA video cable to the computer.
1-2 Connect digital Cable (Only Dual-Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect one end of the 24-pin DVI cable to the back of the
monitor and connect the other end to the computer’s port.
2. Connect the Audio Cable(Only Audio-Input Model)(Optional)
3. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC
outlet.
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
5. If the monitor still does not function properly, please refer to the
troubleshooting section to diagnose the problem.

EN-12

USER CONTROLS
Power Switch / Power LED:
To turn the monitor ON or OFF.
Lights up to indicate the power is turned ON.

Using the Shortcut Menu

Press the function button to open the shortcut menu. The shortcut menu lets you
quickly select the most commonly accessed settings.

Empowering:

Press the Empowering Key to open the Acer eColor Management OSD and access
the scenario modes.

AUTO Auto Adjust:
Press this button to activate the Auto Adjustment function. The Auto Adjustment
function is used to set the HPos, VPos, Clock and Focus.

MENU OSD functions
Press this botton to activate the OSD menu.

V o lu me Up / D o wn
Press to adjust volume (Only Audio-Input Model)(Optional)

INPUT Input Key

Use Input key to select from different video sources that may be connected to
your monitor.
(a) VGA input
(b) DVI input
As you cycle through the sources you will see the following messages on right top
side of screen to indicate currently selected input source. It may take 1 or 2
seconds for the image to appear.
VGA or DVI
If either VGA or DVI input is selected ,but the VGA and DVI cables are not connected, a floating dialog box indicates:
“No Cable Connect” or “No Signal”

EN-13

Acer eColor Management

Operation instructions
Step 1: Press “ “ Key to open the Acer eColor Management OSD and
access the scenario modes
Step 2: Press “ “ or “ ” to select the mode
Step 3: Press “ AUTO “ Key to confirm the mode and run Auto Adjust.

Features and Benefits
Main
Menu
icon

Sub
Menu
icon

Sub
Menu
item

D escription

N/A

User mode

User defined. Settings can be fine-tuned to
suit any situation

N/A

Optimal balance of brightness and contrast
Text mode prevent eyestrain. The most comfortable way
to read onscreen text

N/A

Standard
mode

D efau lt Settin g . R eflects n a tive d isp lay
capability

N/A

Grahpic
mode

Enhances colors and emphasize fine detail.
Pictures and photographs appear in vibrant
colors with sharp detail.

N/A

Movie
mode

Displays scenes in clearest detail. Presents
g re a t visu a ls, e ve n in u n su ita b ly-lit
environments.

EN-14

Adjusting the OSD settings

-------------------------------------------------------------------Note: The following content is for general reference only. Actual
product specifications may vary.

The OSD can be used for adjusting the settings of your LCD Monitor.
Press the MENU key to open the OSD. You can use the OSD to adjust the
picture quality, OSD position and general settings. For advanced settings,
please refer to following page:
Adjusting the picture quality

1 Press the MENU key to bring up the OSD.
2 Using the

keys, select

Picture from the OSD. Then navigate to

the picture element you wish to adjust.
3 Use the / keys to adjust the sliding scales.
4 The Picture menu can be used to adjust the current Brightness, Contrast,
Colour Temp, Auto Config and other image-related qualities.
EN-15

Adjusting the OSD position

1 Press the MENU key to bring up the OSD.
2 Using the directional keys, select

OSD from the on screen display.

Then navigate to the feature you wish to adjust.

EN-16

Adjusting the setting

1 Press the MENU key to bring up the OSD.
2 Using the

keys, select

Setting from the OSD. Then navigate to

the feature you wish to adjust.
3 The Setting menu can be used to adjust the screen Menu Language and
other important settings.

EN-17

Product information

1 Press the MENU key to bring up the OSD.
2 Using the

keys, select

Information from the OSD. Then the

basic information of LCD monitor will show up for current input.

EN-18

TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(VGA Mode)
Problems

Current Status Remedy
LED ON

Using OSD, adjust brightness and contrast
to maximum or reset to their default
settings.

LED OFF

Check the power switch.

Check if AC power cord is properly
connected to the monitor.

Check if video signal cable is properly
connected at the back of monitor.

Check if the power of computer system is
ON.

Unstable
Picture

Check if the specification of graphics
adapter and monitor is in compliance
which may be causing the input signal
frequency mismatch.

Display is
missing, center
shift, or too
small or too
large in display
size

Using OSD, adjust RESOLUTION, CLOCK,
CLOCK-PHASE, H-POSITION and VPOSITION with non-standard signals.

Using OSD, in case of missing full-screen
image, please select other resolution or
other vertical refresh timing.

Wait for a few seconds after adjusting the
size of the image before changing or
disconnecting the signal cable or powering
OFF the monitor.

Check the audio cable with the host PC is
connected.

Check if the volume setup of the host PC is
in minimum position and try to raise the
volume level.

No Picture
LED displays
amber color

Abnormal
Picture

Abnormal
Sound
(Only AudioInput model)
(Optional)

No sound, or
sound level is
too low

EN-19

(DVI Mode)
Problems

Current Status Remedy
LED ON

Using OSD, adjust brightness and
contrast to maximum or reset to their
default settings.

LED OFF

Check the power switch.

Check if AC power cord is properly
connected to the monitor.

Check if video signal cable is properly
connected at the back of monitor.

Check if the power of computer system
is ON.

Check the audio cable with the host PC
is connected.

Check if the volume setup of the host
PC is in minimum position and try to
raise the volume level.

No Picture
LED displays
amber color

No sound, or
Abnormal
sound level is
Sound
(Only Audio- too low
Input model)
(Optional)

EN-20

Declaration of Conformity

We,

And,

Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, E-mail: easy_lai@acer.com.tw
Acer Europe SA
Via Cantonale, Centro Galleria 2 6928 Manno Switzerland
Hereby declare that:
Product:
Trade Name:
Model Number:
SKU Number:

LCD Monitor
Acer
P186HV;P196HQV
P186HVxxxxxx;P196HQVxxxxx(“x” = 0~9, a ~ z, or A ~ Z)

Is compliant with the essential requirements and other relevant provisions of the following EC directives,
and that all the necessary steps have been taken and are in force to assure that production units of the
same product will continue comply with the requirements.

EMC Directive 2004/108/EC as attested by conformity with the following harmonized
standards:
-. EN55022, AS/NZS CISPR22 Class B.
-. EN55024
-. EN61000-3-2, Class D
-. EN61000-3-3

Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1

RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances
in Electrical and Electronic Equipment:

-. The maximum concentration values of the restricted substances by weight in homogenous material are:

Lead
0.1% Polybrominated Biphenyls (PBB’s)
0.1%
Mercury
0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
Hexavalent Chromium 0.1% Cadmium
0.01%

Directive 2009/125/EC with regard to establishing a framework for the setting of
ecodesign requirements for energy-related product.
Year to begin affixing CE marking 2010.

_______________________________

Easy Lai /Manager
Regulation, Acer Inc.

Ma\. , 2010
Date

Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
Trade Name:
Model Number:
SKU Number:

LCD Monitor
Acer
P186HV;P196HQV
P186HVxxxxx;P196HQVxxxxx (“x” = 0~9, a ~ z, A ~ Z or Blank)

Name of Responsible Party:

Acer America Corporation

Address of Responsible Party: 333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:

Acer Representative

Phone No.:

254-298-4000

Fax No.:

254-298-4147

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Acer P196HQVbd Monitor User Guide Manual Operating Instructions
Create Date                     : 2010:03:04 15:39:57Z
Keywords                        : "Acer P196HQVbd, Acer P196HQVbd Monitor Pdf, Acer P196HQVbd User Guide Manual, Acer P196HQVbd Operating Instructions"
Modify Date                     : 2013:08:09 02:22:14+03:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : pdfFactory Pro http://www.pdffactory.com
Metadata Date                   : 2013:08:09 02:22:14+03:00
Format                          : application/pdf
Creator                         : Acer P196HQVbd Monitor User Guide Manual Operating Instructions
Title                           : Acer P196HQVbd Monitor User Guide Manual Operating Instructions
Description                     : Acer P196HQVbd Monitor User Guide Manual Operating Instructions
Subject                         : Acer P196HQVbd, Acer P196HQVbd Monitor Pdf, Acer P196HQVbd User Guide Manual, Acer P196HQVbd Operating Instructions
Producer                        : pdfFactory Pro v1.57 (Windows XP)
Document ID                     : uuid:9a0c7c11-563e-4c3a-a666-59e575e5ad80
Instance ID                     : uuid:e130515d-07b1-4a35-b5d0-38723c3ebc96
Page Count                      : 23
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools

Acer P186HV P196HQVbd Monitor User Guide Manual Operating Instructions To The 348a142c B2bd 424d 846f 7b94112cb6e4

Navigation menu

Versions of this User Manual:

Views

Navigation