Aclara Technologies 6717 Telemetry Transmitter for Automatic Meter Reading User Manual Unknown

Download:
Mirror Download [FCC.gov]
Document ID	61544
Application ID	3BdQDXoKSvIvq6eqrdRiMA==
Document Description	Installation Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.92kB (236438 bits)
Date Submitted	1999-10-01 00:00:00
Date Available	2000-01-27 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat PDFWriter 3.02 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Unknown
Document Author:	Unknown

EXHIBIT F
Ill.
LLWH
September 22, ms
STAR Fri-SET MTL' lNSTALLATlON
PIT COVER PREPARATION
The STAR MTU requires a drilled hole until a minimum dramaer ofl 750 and a
maximum diameter of l 790 Typimll)‘ n 1,750 cote drill is used for cast-inn covers
The outer thickness can be from 250“ to I 315" MTU's for ducks covers (typtfilly
concrete) can be supplied upon request,
Both the top and batotn cnvcr surfam must be evaluated before the hole location is
chosen. The hole location must be selected so that the strength of the lid is not mrhiced
(See wanting below). For example, ribs on the underside ofthc wver must not be out
when boring the hole.
The top surface of the cover must provide a consistent mounting surface for the MTU
flange In general, the flange is designed lobe placed over a smooth surface, or one
covered with closely spaced ribs or humps that are usually ("mind on a non-skid surface.
Hanover, if the surface is inta-ruplad with raised laters or other irregular ddails, the hole
should be located so that the flange misses M “necessary, leaning tint is toured
by the flange on he removed with a simple machining operation that is preformed at the
tune the hole is bored 011m, a cold chisel will remove the leasing
SPACER SELECTION
The pit-set MTU housing is passed through the cover hole and Joined with the fins:
which is snapped over the end cfthe housing The MTU is secured by tightening the
three clamping screws,
Before this is done, it is necessary to select the proper number of spinners so lint the
adjustment range is correct, When the proper number ofspaccrs are used, the top surfice
ofthc cover (flange contact surface) will fall bum the two linen auhoaed on the
housing. This measurement is performed truth the clamp in place and theclamping
screw: fully retracted,
MTL' MOUNTING
Whattltcspaoetcoumisverified, thehmsingtspusedthmghtheholer Theflangets
strapped over the top of the housing. Do not attempt to snap (I! flange in plate by
pressing with the palm of your hand. This tends to apply pressure to the tube and not
tho flange, lnstmd, cup the hand and press with the finger! on the flange only; this is
done while the housing |S held in place with the calm hand When a loud “strap" is
hunt. than the Hang: is in place Note tl'ett the flange may pass beyond the ddatt
location andtonards the cover This is not a problem; when the semis are tightened the
flange vnll slide towards the end of the housing and sup into place with a loud “snap".
LLlSéfl'l
The screws must be tightened evenly so that the clamping forces remain equal. Once the
screws contact the cover they should each be turned only a fraction ofa turn at a time in a
etrcular pattern to insure even clamping. A torque wench must be and to set torque at 4
m —1h_s (64 in — oz). A torque-setting nut driver (such as Gmmgu PIN 6C436) is
issenttal The damning screws require a 5/16" socket
INSPECTING MTU lNSTALLTlON
Proper mounting can be verified by checking that all segments of the flange nrv: properly
sent/ed around the MTU housing lfan) of the segments mnot smooth and flush with
the top surface at the housing, rt means that the cover surface was not smooth orthat
debris was present under the flange In this case the flange must be removed and the
installation redone. (See below)
METER-MT U WIRING
The MTU may be wired to me meter either before or alter installation in the cover. In
fncL m some cam it may be convenient to pie-wire registers and MTU‘: atthe meter
shop.
It is necessary to use the proper splicing equipment to connect the register and MTU If
connection is made at the register. the connections nntst be carefully sealed using
mpounds recommended by the meter nunufnmtmr lftlte mgtsvcr is supplied with an
integml cable and a eablc-to-eehle splice is nude. a gel-filled splice hnx such as 3M
DER-6, dsigned for direct burial, must be used to sfll flte individual splices. This is
absolutely essential with pulse-type rumors (RTK Weignni or Reed Switch). Refer to
Hexagmm wiring infonmxion for hook—up details.
PROGRAMMING
The Psion ham—held programmer, along with the standard about, cable, and probe is
uwd to program file STAR pit-w MTU‘s. The probe is held over the blue down the
housing throughout the programming cycle. See the Prognmmtng Manual for details.
MTU REMOVAL
The flange 3 destgn‘ edlo pemtanenlly smpommlu: MIAU housmg' Whet'tlrlilu is to
beremoved, it isneessarytocuttheflzngetofnalnmettstemovnlfiom «first,
”fluscanbc donebylooseningtheclarnpscrewsattdwmngdteflangeatane i
usmg ttn Snips. wit: cult/er. or chisel.
WARNING:
. . ‘
Drilling the pit cover may compromise the cover strength. Hengrntn is no
responsible for darn-[es due to the cover mdtl'scmont.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : 
Create Date                     : Thursday, September 30, 1999 3:44:04 PM
Title                           : Unknown
Author                          : Unknown
Producer                        : Acrobat PDFWriter 3.02 for Windows
Subject                         : 

EXIF Metadata provided by EXIF.tools