Aclara Technologies 9975T Aclara Synergize RF Network DCU XCVR User Manual 101 9975T SRFN
Aclara Technologies LLC Aclara Synergize RF Network DCU XCVR 101 9975T SRFN
Contents
- 1. Users Manual
- 2. Label Instruction
- 3. User Manual
Users Manual
DRAFT 101-9975T-SRFN User Manual www.Aclara.com DRAFT DRAFT Proprietary Notice Information contained in this document is private to Aclara Technologies LLC an Ohio limited liability company (Aclara). This information may not be published, reproduced, or otherwise disseminated without the express written authorization of Aclara. Any software or firmware described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license. Disclaimer The information in this document is subject to change without notice and should not be construed as a commitment by Aclara. Aclara assumes no responsibility for any errors that may appear in this document. No responsibility is assumed for the use or reliability of software on equipment that is not supplied by Aclara. TWACS, STAR, and Metrum Cellular are registered trademarks of Aclara Technologies LLC. Aclara Technologies LLC Confidential and Proprietary Copyright 2015. All Rights Reserved. 101-9975T-SRFN User Manual DRAFT DRAFT WARNINGS, CAUTIONS, AND NOTES Always consult and adhere to all local and national safety codes, regulations, and standards.WARNING, CAUTION and Note statements are used throughout this manual to emphasize important and critical information to help you ensure safety and prevent product damage. These statements are defined below. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious physical injury. CAUTION Indicates a situation, which, if not avoided, could result in damage to equipment, damage to software, loss of data or invalid results. NOTE Indicates important supplemental information. MTU Installation Guidelines iii DRAFT FCC/IC Compliance FCC/IC Compliance The following statements cover the RF exposure guide and the field calibration procedure. FCC/IC RF Exposure Guide Aclara Technologies LLC low power RF devices and their antennas must be fixed-mounted on indoor or outdoor permanent structure(s) providing a separation distance of at least 20 cm from all persons during normal operation. This device is not designed (and it has no external connection) to operate in conjunction with any other antennas or transmitters. No other operating instructions for satisfying RF exposure compliance are needed. Field Calibration Procedure Aclara Technologies LLC low power RF devices have passed through extensive and multitask testing and calibration procedures while in the factory. Therefore, no additional calibration or adjustment is required in the field. Aclara Technologies LLC low power RF devices are shipped to the customer in the sealed enclosures. Thus, no adjustments can be made in the field, without breaking the factory sealed enclosure. Antenna This radio transmitter (4546A-9975T) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. iv Manufacturer Manufacturer Part Number dBi Laird Technologies MAXRAD FG4605 MFB4605(NF) MTU Installation Guidelines DRAFT Avertissements, mises en garde et remarques AVERTISSEMENTS, MISES EN GARDE ET REMARQUES Toujours consulter et respecter les codes, règlements et normes de sécurité locaux et nationaux. Des AVERTISSEMENTS, MISES EN GARDE et remarques sont utilisés tout au long de ce guide pour souligner l'information importante et critique qui vous aidera à assurer la sécurité et à prévenir les dommages au produit. Ces énoncés sont définis ci-dessous. AVERTISSEMENT indique une situation potentiellement dangereuse qui, si elle n'était pas évitée, pourrait entraîner la mort ou des blessures graves. MISE EN GARDE indique une situation qui, si elle n'était pas évitée, pourrait entraîner des dommages à l'équipement, des dommages au logiciel, des pertes de données ou des résultats invalides. REMARQUE indique des informations supplémentaires importantes. MTU Installation Guidelines DRAFT Conformité FCC/IC Conformité FCC/IC Les énoncés qui suivent portent sur le guide d'exposition aux RF et la procédure de calibration sur place. Guide d'exposition aux RF FCC/IC Les appareils RF à faible puissance Aclara Technologies LLC ainsi que leurs antennes doivent être montés de manière fixe sur des structures intérieures ou extérieures permanentes qui se trouvent à au moins 20 cm des personnes pendant le fonctionnement normal. Cet appareil n'est pas conçu (et il n'a aucun branchement externe) pour être utilisé en association avec toute autre antenne ou tout transmetteur. Aucune autre instruction d'utilisation n'est requise pour assurer la conformité aux règles d'exposition aux RF. Procédure de calibration sur place Les appareils RF à faible puissance Aclara Technologies LLC ont été soumis à des tests étendus et multi-tâches et à des procédures de calibration complexes en usine. Par conséquent, ils ne requièrent pas de calibration ni d'ajustement supplémentaire sur place. Les appareils RF à faible puissance Aclara Technologies LLC sont expédiés au client dans des boîtiers scellés. Aucun ajustement ne peut donc être effectué sur place sans briser le boîtier scellé en usine. Antenne Cet émetteur radio (4546A-9975T) a été approuvé par Industrie Canada pour fonctionner avec l'antenne types énumérés ci-dessous avec le maximum de gain admissible indiqué. Types d'antenne non inclus dans cette liste, ayant un gain supérieur au gain maximum indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. vi Référence du fabricant Numéro de pièce fabricant dBi Laird Technologies MAXRAD FG4605 MFB4605(NF) MTU Installation Guidelines DRAFT 9975T FINAL TEST INSTRUCTION Written by: Title: David George Test Engineer Revision History Revision Description Initial Release Added firmware checks Revised by D George D George Date 2015‐11‐12 2015‐11‐12 Purpose The purpose of this document is to provide instructions for testing of the 9975T transciever board during Final DCU Test and Integration. Scope The scope of this instruction includes the testing of functionality of the transmit and all 8 receive channels, as well as configuring customer settings. Related Documents SRFNI-XCVR Configuration Workflow 477-2015-001-TRS 101-9975T-SRFN User Manual DRAFT Test Instruction Test Instruction CAUTION: Make sure antenna cable is plugged into the DCU! This test transmits to an end point and transmitting without a load can damage the transmitter! 1. Plug the communications cable into the 4-pin connector J19 of 9975T board. 2. Make sure DCU under test has been powered for at least 2 minutes to allow 9975T time to boot up. 3. On DCU Main board verify: CPU Board has 02.40.0009 Firmware or higher • 9975T board is recognized with a “w” response and reports a firmware version of 1.10.0033 • Make a note of the current number of test records • 101-9975T-SRFN User Manual DRAFT Test Instruction 4. Launch the Final Test – 9975T application. 5. Select Setup, and set the correct Comm Properties. 6. Click the Get Port Names button. 7. Select the correct COM Port Name for the cable that is plugged into the 9975T board. 8. Click the Connect button. 9. Select Read Configuration, and verify communications response from the 9975T. 10. Select Set MAC Network ID and set MAC Network ID to 0. 11. Click the Configure Board button. 12. Verify all receive channels are set to the correct frequency. 101-9975T-SRFN User Manual DRAFT Test Instruction 13. Verify Transmit Channel frequency. 14. If all frequencies are set correctly, select Ping Test. 15. Verify Radios 1 – 8 have received a ping response from the factory end point with a signal strength no less negative than -30 dBm 101-9975T-SRFN User Manual DRAFT Customer Configuration Instruction Customer Configuration Instruction 1. Verify communications with 9975T by clicking Read Configuration, if necessary 2. Click the Configure button. 3. Select the appropriate customer .xml file. 4. Click the Open button. The program will now configure the 9975T with customer frequencies and settings. 5. Select Read Configuration, and verify that the frequency settings are correct per customer work order (move the scroll bar of the output window up to display Receive and Transmit Frequencies). 101-9975T-SRFN User Manual Customer Configuration Instruction DRAFT 6. Click on Power Up Self Tests. 7. Verify that RTCFailCount, SecurityFailCount and NvmRWFailCount are all set at 0. 8. Verify that shipMode 1 write was successful. (It may be necessary to click twice to see shipMode write successful.) 9. Verify number of test records has increased on DCU Main Board 101-9975T-SRFN User Manual
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : cwebb Create Date : 2015:11:20 10:10:46Z Modify Date : 2015:12:18 16:46:30-08:00 Has XFA : No Language : en XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : FrameMaker 12.0.4 Metadata Date : 2015:12:18 16:46:30-08:00 Producer : Acrobat Distiller 11.0 (Windows) Format : application/pdf Title : 101-9975T-SRFN User Manual.book Creator : cwebb Document ID : uuid:bd5461e3-416a-4227-97da-bb27e5d2bc8b Instance ID : uuid:6b248cf1-0e86-47e3-9a20-c9fbb6241762 Page Mode : UseNone Page Count : 14EXIF Metadata provided by EXIF.tools