Acoustic Arc AAI-DS0620A-0 Wireless Speaker System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1255045
Application ID	E3v/lq5ICJR9shWNCQPecQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.96kB (236965 bits)
Date Submitted	2010-03-22 00:00:00
Date Available	2010-03-22 00:00:00
Creation Date	2010-02-22 10:51:28
Producing Software	PDF-XChange 3.60.0106 (Windows XP)
Document Lastmod	0000-00-00 00:00:00
Document Title	User Manual

DS0620A
2.4GHz Wireless Outdoor
Speaker System
Owner's Manual
(Read carefully the instructions before using this system)
Introduction
This 2.4GHz digital wireless speaker system utilizes the most advanced wireless technology to
deliver dynamic, high-quality audio anywhere inside or outside your home. The wireless audio
transmission travels freely through walls, floors and other solid objects. Simply connect the
system to any audio source such as Radio, TV, VCR, Hi-Fi and CD/MP3/ VCD/DVD players... to
enjoy full-spectrum, lifelike sound without complicated wiring and installation.
Features
1. 2.4GHz Frequency Hopping Spread Spectrum (FHSS) digital transmission.
2. 32-Channel scan-tuning between transmitter and receiver.
3. Audio output power up to 20 Watts RMS per channel.
4. Weather-resistant speaker and remote control.
5. Mood light effect.
6. Dual weather-resistant speaker driver (super bass and tweeter built-in).
7. Pairing between transmitter and speaker
8. Supports stereo audio (with optional additional speaker).
9. AUX In jack.
10. Operating distance up to 50 meters in open area (less through walls and other obstructions).
11. Works through walls, floors and anywhere in the room.
12. Virtually interference-free stereo quality.
13. Electronic Volume Control on Speakers
14. Remote control unit.
15. Powered by 6 D batteries, or by included AC/DC adapter.
Package content
i. 1 x RF transmitter
ii. 1 x RF speaker
iii. 1 x Remote control
iv. 1 x ac/dc adapter for transmitter
v. 1 x ac/dc adapter for speaker
vi. 1 x RCA to RCA cable
vii. 1 x 3.5mm to 6.3 mm adapter plug
viii. 1 x user manual
Transmitter
Speaker
Remote Control
Installation
Transmitter
1. Plug the included AC/DC adapter into a standard wall outlet.
2. Insert the adapter connector plug firmly into the DC IN jack located on the rear panel of the
transmitter base.
3. Extend the retractable audio cable located on the back panel of the transmitter and connect it
to the output jack of virtually any audio source.
Note : Do not fully extend the cable until ready to retract.
4. To retract the cable, pull it until it is fully extended and then allow it to feed back into the
base.
Speaker Receiver
Battery Power
1. To operate the speaker using battery power, gently turn the speaker over and open the
battery compartment cover located underneath.
2. Insert six (6) D alkaline batteries (not provided) into the battery compartment, observing
proper +/- polarities as indicated.
3. Replace the battery compartment cover.
AC Power
1. To operate the speaker using AC power, plug the included 12V power adapter into a
standard wall outlet.
2. Insert the power adapter connector firmly into the DC IN jack located on the back panel of
the speaker.
Operation
1. To switch on the speaker, press the POWER button 3sec. located on the front panel of the
speaker. The GREEN power LED illuminates.
2. To switch off the speaker, press the POWER button 3sec again.
Remote Control
The remote control is ready to use with a factory-installed button cell battery. It can be stored
in the recessed area on the front panel.
Basic Operation
1. When the transmitter power adapter is connected and plugged into a standard wall outlet, the
transmitter's GREEN led remains on.
2. To switch on the speaker, press the POWER button 3sec on the front panel of the speaker.
The GREEN led illuminates.
3. Turn on the audio source the transmitter is turned off for less then 4 minutes, the blue LEDs
on the transmitter and the speaker illuminate when the audio signal link between the two is
made.
4. If the audio source connected to the transmitter is turned off for less than 4 minutes, the
BLUE leds on the transmitter and the speaker remain on, but no sound is transmitted.
When the audio signal returns to the transmitter, sound is transmitted again.
5. If no signal is detected for more than 4 minutes, the transmitter automatically turns off ; the
BLUE leds on the transmitter and the speaker switch to GREEN.
6. If no signal is detected from the transmitter for more than 5 minutes, the speaker
automatically shifts to Standby mode.
7. To turn on the speaker again during Standby mode, press the POWER button on remote
control unit. (not need, please delete)
8. If no audio signal is detected from the transmitter for more than 15 minutes, the speaker
automatically turns off. The GREEN led goes off.
9. To switch on the speaker, press the POWER button 3sec on the front panel of the speaker.
10. To switch off the speaker. Press the POWER button 3sec again.
PAIRING
1. If there is no audio sound is detected after connecting is done, re-pairing processes is
required.
2. Press the “PAIR” buttons on both transmitter and speakers Mood light /Pair button for 5
seconds, there will have a “Du” sound detected when the pairing process is finished.
Mood Light
For mood light effect, press the LIGHTS button on the speaker or remote control.
Left / Right Channel and Mono Selection
The Wireless Outdoor Speaker System comes with one speaker and is designed for either Mono or
Stereo playback. For stereo playback, an additional speaker must be purchased separately. Mono
playback is suggested when only one speaker is used in an area or room.
Mono Playback
To enable Mono playback, ensure that the switch located on the back panel of the speaker is in the
MONO position.
Stereo Playback
To enable Stereo playback, set the switch on one of the two speakers' back panel to LEFT. Set the
switch on the other speaker to RIGHT.
Note 1 : It is also possible to listen to only the Left or Right audio channel using only the speaker
set. To do so, simply set the switch on the speaker's back panel to LEFT or RIGHT. Only the
channel selected will be audible.
Note 2 : If two speakers are connected to the system, ensure both speakers are placed within the
effective operational range. If either speaker is out of range it will cause distortion to both
speakers.
AUX In
To connect an audio device directly to the speaker, insert the output audio cable from the device into
the AUX In jack located on the back panel of the speaker.
Note :
If the source signal is too weak for reception, the transmitter automatically switched off after
approximately 4 minutes to protect the unit and save power. If the source signal returns to an
adequate level, the transmitter automatically switches back on.
When the transmitter is in Standby mode, the speaker automatically switches off after
approximately 20 minutes to protect the unit and save power.
To switch speaker power back on during Standby mode, press the POWER button on the remote
control. The signal link between the transmitter and speaker reconnects automatically.
Troubleshooting
No sound
Ensure the AC adapter is securely plugged into the wall outlet and the transmitter DC IN jack.
Ensure the speaker POWER button is in the ON position.
Speaker batteries may be too weak. Replace with new batteries or connect with the included
ac/dc adapter.
Ensure the connected audio device is switched on and producing a signal.
Ensure that the volume level is set to a moderate level.
Redo the pairing process by pressing the “Pair” button on the speakers and transmitter
simultaneously.
Distortion
Speaker batteries may be too weak, Replace with new batteries or connect with the included
ac/dc adapter.
Ensure that the volume level is set to a moderate level.
The speakers are too fat from the transmitter. Move closer to the transmitter base.
The audio input signal may be too low : increase the volume level of the audio source.
If two speakers are connected to the system, ensure both speakers are placed within the effective
operational range. If either speaker is out of range it will cause distortion to both speakers.
Specifications
Transmission Mode :
UHF Stereo
Carrier Frequency :
2.4GHz Digital
Operation Voltage :
Transmitter, DC 6C 300mA
Speaker, DC 12V 1.5A or 6 x D alkaline batteries (not included)
Remote Control, 1 x CR2032 button cell
Frequency Response :
30 Hz – 20 KHz
Distortion :
0.5%
S/N Ratio :
65 dB
Operation Distance :
Up to 50 meters (open area)
Speaker Audio Output Power : 20W Max. (RMS)
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
If you have any questions ,Please feel free to our website : www.acousticarc.com
Our model no.: DS0620A , 2.4GHz wireless speaker system.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Producer                        : PDF-XChange 3.60.0106 (Windows XP)
Create Date                     : 2010:02:22 10:51:28+08:00
Page Count                      : 8

EXIF Metadata provided by EXIF.tools