Acrox Technologies MU07 2.4G Wireless Mouse User Manual
Acrox Technologies Co., Ltd. 2.4G Wireless Mouse
User Manual
2.4GHz Wireless Ergo BlueTrace Mouse w/Nano Receiver USER'S GUIDE Ver.:1.00 CAUTION: To use this product properly, please read the user's guide before installing. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Functional Introduction LED Indicator Connect Button Scrolling Wheel Battery Cover Right button Left button Nano Receiver ON/OFF Switch Installing the batteries Step 1: Take the battery cover off. Step 2: Insert the batteries as shown inside the battery compartment. Step 3: Replace the cover. Pull 1âst 2ând AAA Battery **Warning: *Please insert the battery with the correct position according to the instruction labeled on the mouse. Setup the Connection between the Receiver and the Mouse 1. Insert the batteries into the mouse, then follow the steps below. 2. In the meantime, to open the mouse under the cover, take the nano receiver out. 3. Plug the Nano receiver into the USB port on your computer. 4. If the mouse does not work, please put it into pairing mode. 5. Pairing: Re-plug the receiver into the USB port on your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function). 6. The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver. 7. When low battery, the battery indicator on the mouse will start to blink. LED Indicator *Mouse Indicator LED is on for 3 sec. Power ON LED Blinks for 3 times During Pairing LED Blinks for 10 sec. Low Battery Warning
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract XMP Toolkit : 3.1-701 About : 7259f394-1343-11e1-0000-02dbbe4a6057 Producer : GPL Ghostscript 9.0 Keywords : Modify Date : 2011:12:29 17:41:40+08:00 Create Date : 2011:11:17 14:45:38+08:00 Creator Tool : PDFCreator Version 1.2.0 Metadata Date : 2011:12:29 17:41:40+08:00 Document ID : 7259f394-1343-11e1-0000-02dbbe4a6057 Instance ID : uuid:683cfea4-7368-4336-b8b9-fda30c909889 Format : application/pdf Title : 2.4G BlueTrace Mouse_GME+Nano RX Users Guide_2011_???@?O_ Creator : Debby Description : () Page Count : 5 Subject : Author : DebbyEXIF Metadata provided by EXIF.tools