Acrox Technologies RX03 Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1602797
Application ID	OSclAFIWbVLBQZnluBc1iQ==
Document Description	User Man_PRDRX04
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.06kB (100688 bits)
Date Submitted	2011-12-14 00:00:00
Date Available	2011-12-14 00:00:00
Creation Date	2011-03-30 17:04:56
Producing Software	GPL Ghostscript 8.61
Document Lastmod	2011-11-28 11:21:09
Document Title	User manual
Document Creator	PDFCreator Version 0.9.5
Document Author:	XeniaHuang

2.4GHz Wireless
Optical Ergo Mouse
w/Nano Receiver
USER'S GUIDE
Ver.:1.00
CAUTION: To use this product properly, please read the user's guide before installing.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
French translation:
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
Functional Introduction
Nano Receiver
Battery Cover
LED Indicator
Connect
Button
Scrolling Wheel
Right button
ON/OFF Switch
Backward
Left button
Forward
Forward
Press this button to view the next page in your Internet browser.
Backward
Press this button to view the previous page in your Internet browser.
Installing the batteries
Step 1: Take the battery cover off.
Step 2: Insert the batteries as shown inside the battery compartment.
Step 3: Replace the cover.
Step 4: Turn on power switch
2’nd
1’st
AAA Battery
**Warning:
*Please insert the batteries with the correct position according to the instruction
labeled in the mouse.
Battery warning statement:
Do not mix old and new batteries
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad,
ni-mh, etc) batteries.
Setup the Connection between the Receiver and the Mouse
1. Plug the Nano receiver into the USB port of your computer.
2. Insert the batteries into the mouse, then follow the steps below.
3. If the mouse is not working, please put it into pairing mode or check
the batteries power status.
4. Pairing: Re-plug the receiver into the USB port of your computer, then
press the connect button on the mouse. If the mouse does not work
after 10 seconds, pair them again. (The receiver has auto pairing
function).
5. The LED indicator on mouse flashes steadily when it is in pairing
mode and stops blinking when it is successfully paired with the
receiver.
6. When the batteries of the mouse is low, the Low Power indicator
will start to blink.
LED Indicator
*Mouse Indicator
Red LED is on for 10 sec.
Power ON
Red LED Blinks for 10 sec.
Low Battery Warning
Green LED Blinking
Pairing (LED OFF when paired or
failed after 10 sec.)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
About                           : 4cbf9167-5d08-11e0-0000-68beb15519f3
Producer                        : GPL Ghostscript 8.61
Keywords                        : 
Modify Date                     : 2011:11:28 11:21:09+08:00
Create Date                     : 2011:03:30 17:04:56+08:00
Creator Tool                    : PDFCreator Version 0.9.5
Metadata Date                   : 2011:11:28 11:21:09+08:00
Document ID                     : 4cbf9167-5d08-11e0-0000-68beb15519f3
Instance ID                     : uuid:a81e13e7-4957-4a1c-a7f0-eb1b9ea6c8d5
Format                          : application/pdf
Title                           : User manual
Creator                         : XeniaHuang
Description                     : 
Page Count                      : 5
Subject                         : 
Author                          : XeniaHuang

EXIF Metadata provided by EXIF.tools