Actiontec Electronics GT784WN Wireless 11n ADSL2 Modem Gateway User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1356124
Application ID	DmbTeHW+Q8Gg65WnDHegSA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.96kB (112040 bits)
Date Submitted	2010-10-08 00:00:00
Date Available	2010-10-08 00:00:00
Creation Date	2010-09-03 17:14:24
Producing Software	Xerox WorkCentre 7435
Document Lastmod	2010-09-03 17:17:27
Document Title	Users Manual
Document Creator	Xerox WorkCentre 7435

Actiontec GT784WN Quick Start Guide
Connect the Gateway to a Computer
1. Get GT784WN Wireless 11n ADSL2 Modern Gateway from the Qulck Start KIt and take It out of the bag.
2. Get the Power Cord from your DSL Qulck Start KIt.
3, Plug the smaller end of the Power Cord Into the Black Port on the back of the Gateway.
4. Plug the larger end of the Power Cord into a Power Outlet.
5. Make sure the Power Switch Is On.
6. Make sure the Power Light on the Gateway Is SOLID Green.
7. Get the Yellow Cable
8. Plug one end of the Vellow Cable Into any of the Yellow Ports on the back of the Wireless DSL Gateway.
9. Make sure that your computer Is turned on. Then, plug the other end of the Vellow Cable Into the
Ethernet Port on the back of the computer. An Ethernet Port looks similar to a regular Phone Jack, but Is
slightly larger.
10. Make sure that 1 of the 4 Ethernet lights on the Gateway is Green. Thls may take a few moments.
11. Get the Black or Gray DSL Cable from your DSL Quick Start Kit.
12. Plug one end of the DSL Cable into the Gray Port located on the back of the Gateway.
13. Plug the other end of the DSL Cable Into the PhoneJack closest to your Computer.
14. Make sure All Devices with the same phone number as your DSL LIne have Phone Filters. This includes
telephones , fax machines, caller ID boxes, satellite TV recelvers, TIVo devices, and answering machlnes.
15. Make sure that that Power and DSL Lights are solid Green. Thls may take up to 30 seconds.
Note: If the DSL nght continues to bllnk, make sure you received notification from your DSL Internet Servlce
Provider that your DSL service has been activated.
Configure the Gateway
1. Open a Web Browser (Netscape Navigator or Internet Explorer, for example). In the address bar, enter
http://192.168.0.1 then press Enter on the keyboard.
Note: when you open your web browser you may get a page cannot be displayed error. This is normal and
will not effect the instructions in step 1.
2. The "Main Menu" screen appears. Select Auto Configure your Gateway.
Note: If this screen does not appear, make sure our Ethernet port Is configured for Dynamic IP.
3. The "Welcome" screen appears. Click Next.
4. The Modem Is now detecting your Internet provider‘s settings. This process can take up to 3 minutes.
5. In the next window, enter the User Name and Password provided by the ISP. CIIck Next
Configure Wireless Connection and Security
1. Click the Yes button.
2. Select a name for your wlreless network and enter it in the "ESSID" fieldt Then click NEXT to continue.
3 It Is recommended that you secure your wlreless network by clicking Yes. If you choose not to secure
your network by clIckIng Ves. If you choose not to secure your network, cllck No and you wIII have
completed the installation.
4. Select the type of wlreless security that you want to use Actlontec recommends using WPA&WPA2. The
following steps will show you how to enable WPA&WPA2 wlreless security.
Note: All of your other wireless devices will need to support that same type of wireless securlty chosen In
order to connect to your wlreless network.
5. Enter in a password or pre-shared key. The key must be at least 8 characters long. Click NEXT to contlnue.
6. The "Congratulatlons" screen appears. The DSL nght will glow SOLID Green and the Internet Light will
flicker Green indicating Internet actlvltyi
Congratulations you are now connected!
General Regulatory and Compliance Notices
Important Safety Instructions
If applicable. when using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical
shock. and personal injury, including the following:
0 Do not use this product near water - for example, near a bathtub kitchen sink, laundry tuoor swimming pool, or in a wet basement;
0 Avoid using a telephone (other than a cordless type) during an electrical storm, as there may be a remote risk of electrical shock
due to lightning;
0 Do not use thetelephone to report a gas leak in the vicinity of the leak;
o Use only the power cord and batteries indicated in this manual;
0 Do not dispose of batteries in fire, as they may explode — check with local codes for possible special disposal instructions,
Telephone Line Cord Caution
To reduce the risk of fire. use only No. 26 AWG or larger (e,g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.
Coaxial Cable
Ifapplicablethe coaxial table screen shield needs to be connected to the Earth at the building entrance per ANSI/NFPA 70,the National Electrical
Code MEG), in particular Section 82093,"Gromding of Outer Conductive Shield of a Coaxial Cable."or in accordance with local regulation.
FCC Class B Equipment
This equipment has been tested and found to comply with the limits for a Class 3 digital device. pursuant to Part 15 of the FCC Rules These
limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment genemtES.
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this
equipment doescause harmful interference to radio ortelevision receptionwhich can be determined by turning the equipment off and
on, me user is encouraged to try and correct the interference by implementing one or more of the following measures
0 Reorient or relocate the receiving antenna:
0 Increase the separation between the equipment and receiver;
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected;
. Consult the dealer oran experience radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Actiontec Electronics Inc, may void the user‘s authority to operate the equipment
Declaration oi conformity for products marked with the FCC logo — United States only.
This devices complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1,This device may not cause harmful interference;
2.This device must accept any interference received including interference that may cause unwanted operation.
Important Note
If applicablethis equipment complies with FOC radiation exposure limits set forth foran uncontrolled environment. This equipment
should be installed and operated with minimum distance 20 cm between the radiator and your body.
The transmitter must not be colocated or operating in conjunction with any other antenna or transmitter,
For questions regarding your product or the FCC declaration, contact:
Aetiontec Electronics. Inc
760 North Mary Avenue,Sunnyvale. CA 94086, United States
Tel: (408) 752-7700 Fax: (408) 541-9005
PN 05300601 -100
PI1022/0210

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Create Date                     : 2010:09:03 17:14:24-07:00
Creator Tool                    : Xerox WorkCentre 7435
Modify Date                     : 2010:09:03 17:17:27-07:00
Metadata Date                   : 2010:09:03 17:17:27-07:00
Producer                        : Xerox WorkCentre 7435
Format                          : application/pdf
Document ID                     : uuid:97c98e4d-2892-4b00-97f2-1f7d6210433e
Instance ID                     : uuid:15ad8902-91f1-4e31-abdd-030e15501bbe
Page Count                      : 3
Creator                         : Xerox WorkCentre 7435

EXIF Metadata provided by EXIF.tools