Actiontec Electronics WCB3000 Wireless Coax Network Adapter User Manual Quick Start Guide

Download:
Mirror Download [FCC.gov]
Document ID	1892826
Application ID	Casb9KP9w02w8GQll9qd9w==
Document Description	Quick Start Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.41kB (205164 bits)
Date Submitted	2013-02-04 00:00:00
Date Available	2013-02-04 00:00:00
Creation Date	2013-02-01 17:51:49
Producing Software	Adobe Acrobat 6.0
Document Lastmod	2013-02-02 14:08:08
Document Title	Quick Start Guide
Document Creator	Adobe Acrobat 6.0

FCC_GR&CN_pkginsrt_Canada7_FCC Reg_Comp sheet_10x6 1/17/13 12:20 PM Page 1
General Regulatory and Compliance Notices
Important Safety Instructions
Modifications
If applicable, when using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical
shock, and personal injury, including the following:
Do not use this product near water – for example, near a bathtub, kitchen sink, laundry tub, or swimming pool, or in a wet basement;
Avoid using a telephone (other than a cordless type) during an electrical storm, as there may be a remote risk of electrical shock
due to lightning;
Do not use the telephone to report a gas leak in the vicinity of the leak;
Use only the power cord and batteries indicated in this manual;
Do not dispose of batteries in fire, as they may explode – check with local codes for possible special disposal instructions.
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Actiontec Electronics, Inc, may void the user’s authority to operate the equipment.
•
•
•
•
•
Declaration of conformity for products marked with the FCC logo – United States only.
This devices complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions:
1.This device may not cause harmful interference;
2.This device must accept any interference received, including interference that may cause undesired operation of the device.
Telephone Line Cord Caution
To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.
Canadian Industry Regulations
This product meets the applicable Industry Canada technical specifications.
Coaxial Cable
The Class [B] digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation.
If applicable, the coaxial cable screen shield needs to be connected to the Earth at the building entrance per ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, “Grounding of Outer Conductive Shield of a Coaxial Cable,” or in accordance with local regulation.
Important Note
For Audio/Video Apparatus
This reminder is provided to call the CATV system installer's attention to Section 820.93 of the National Electric Code (NEC), which provides
guidelines for proper grounding and, in particular, specifies that the coaxial cable shield shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
If applicable, this equipment complies with FCC/Industry Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Please heed all warnings; read, keep and follow all instructions. Do not use this apparatus near water and only clean with dry cloth.
The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that
this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the
technology.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such
as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile
satellite systems.
The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-topoint and non point-to-point operation as appropriate.
FCC Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by implementing one or more of the following measures:
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and receiver;
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected;
Consult the dealer or an experience radio or television technician for help.
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For questions regarding your product or the FCC/Industry Canada declaration, contact:
Actiontec Electronics, Inc
760 North Mary Avenue, Sunnyvale, CA 94086, United States
Tel: (408) 752-7700 Fax: (408) 541-9005
•
•
•
•
PN 0530-0601-103
PI1176/0113
WCB3000 Quick Start Guide
This Quick Start Guide will walk you through the easy steps to install your WCB3000
Network Adapter. We’ll show you how to configure and connect the Adapter.
To do this, you will need the following items:
• A WCB3000 Network Adapter
• An External Power Supply (5VDC/3A; Made by AcBel, Model: WAC010)
• Coaxial cable(s) or Ethernet cable(s)
1. Configure the WCB3000 Network Adapter’s Wireless Settings
You’ll need to configure the Adapter’s wireless settings first, prior to connecting
and installing it in its final location.
Step 1
Get the power supply for the Adapter. Plug one end of the power supply into the
Power port on the back of the Adapter.
Step 2
Plug the other end of the power supply in a nearby power outlet.
Step 3
Get an Ethernet cable. Plug one end into one of the four yellow Ethernet ports on
the back of the Adapter. Plug the other end into an Ethernet port on your
computer.
Step 4
Wait approximately one minute. Then, open a web browser on your computer
and enter 192.168.99.254 into the browser’s address bar.
Step 5
The Wireless Extender’s configuration GUI supports three login accounts with
different access rights. The username/password combinations are:
user/user
tech/tech
mso/mso
The table below shows the access rights for each type of login account:
Step 6
Configure Wireless SSID and password to your own. Please note WCB3000
support both 2.4GHz and 5GHz operating simultaneously. You may configure
both radios at the same time.
2. Connect the WCB3000 Network Adapter
To connect the Adapter properly, please connect the Adapter to your BROADBAND
ROUTER via Ethernet or coaxial cable at its final location, after the Adapter is
configured.
Step 1
Get a coaxial cable and plug one end into the Coax port on the back of the Adapter.
Plug the other end of the cable into a coaxial port in the wall.
Step 2
Power up the WCB3000 Network Adapter by plugging power supply into a nearby
power outlet. Wait until the Coax LEDs on both BROADBAND ROUTER and
WCB3000 glow solid green.
Alternative Configuration
Instead of Steps 1‐2 in the above procedure, get an Ethernet cable and plug one end
into a yellow Ethernet port on the back of the WCB3000 Network Adapter. Then,
plug the other end into a LAN port on BROADBAND ROUTER.
Congratulations! You have successfully installed WCB3000 Network Adapter.
Specifications
1. Features
Wireless
o Dual Band concurrent (2.4Ghz and 5Ghz)
2.4/5 GHz IEEE 802.11n 2x2
External PA for 5Ghz radio
Supports both 20 MHz and 40 MHz channels
Full IEEE 802.11 a/b/g/n legacy compatibility with enhanced performance
Comprehensive wireless network security support that includes WPA, WPA2,
and AES encryption/decryption
Ethernet
o Two 10/100/1000 Gigabit Ethernet ports
MoCA Coax
o MoCA 1.1 compliant
o Two coaxial F‐connectors
2. Power requirements
•
Operating voltage:
+5V +/‐ 5% @ 3A max
•
Power Dissipation Active:
5V DC @ xxx mA (typical)
3. Environmental Operating Range
•
Operating temperature:
0º C to 50º C (32º F to 122º F)
•
Humidity:
8‐95%, non‐condensing
4. Dimension and Weight
•
7.5” (L) x 5.1” (W) x 1.5” (H)
0.75 lb.
5. Certifications
•
FCC Part 15 Class B, Class C; Safety UL/cUL

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:02:02 14:08:08-08:00
Create Date                     : 2013:02:01 17:51:49-08:00
Metadata Date                   : 2013:02:02 14:08:08-08:00
Document ID                     : uuid:3cc3c0b4-7609-4567-8f38-40332a7724ee
Instance ID                     : uuid:41d0ebaf-3f34-442e-b6f3-3d0100d03dbd
Format                          : application/pdf
Has XFA                         : No
Page Count                      : 5
Creator                         : Adobe Acrobat 6.0
Producer                        : Adobe Acrobat 6.0

EXIF Metadata provided by EXIF.tools