Actisys Act Ir200L Users Manual
ACT-IR220L to the manual 81e55856-917c-4d66-ab6a-fc269d2b9da3
2015-02-05
: Actisys Actisys-Act-Ir200L-Users-Manual-504441 actisys-act-ir200l-users-manual-504441 actisys pdf
Open the PDF directly: View PDF .
Page Count: 36
Download | |
Open PDF In Browser | View PDF |
ACTiSYS Corp. Serial-IR Dongle Installation Manual ACT-IR220L+/220L/200L IrDA PC Adapter User’s Manual ACTiSYS Corp. 48511 Warm Springs Blvd, Suite 206 Fremont, CA 94539, USA TEL: (510) 490-8024, FAX: (510) 623-7268 E-Mail: irda-support@actisys.com Web: www.actisys.com Release 1.5 ACTiSYS Corporation 2001 1 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual FCC & VCCI Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING-FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user authority to operate this equipment NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Increase the separation between the equipment and receiver. -Reorient or relocate the receiving antenna. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for helps. This equipment is in the 2nd Class category (information equipment to be used in a residential area there to) and conforms to the standards set by the Voluntary Control Council For Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential area. When used near a radio or TV receiver, it may become the cause of radio interference. Read the instructions for correct handling. NOTE: Must be used with shielded cable only. FOR YOU RECORDS For your assistance in reporting this product in case of loss or theft, please record the model and serial number that is located on the bottom of the case. Please retain this information. Model Number Serial Number Date of Purchase Place of Purchase All indicated copyrights and trademarks in the following pages are copyrights and trademarks of their Respective corporations. Release 1.5 ACTiSYS Corporation 2001 2 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual CONTENTS CONTENTS............................................................................................................................................. 3 INTRODUCTION ..................................................................................................................................... 4 PACKING CHECK LIST.......................................................................................................................... 4 SYSTEM REQUIREMENTS .................................................................................................................... 4 BIOS SETUP VERIFICATION ................................................................................................................. 4 WINDOWS 98 INSTALLATION GUIDE .................................................................................................. 5 WINDOWS 98 UNINSTALLATION GUIDE ............................................................................................. 9 WINDOWS 2000 INSTALLATION GUIDE............................................................................................. 11 WINDOWS 2000 UNISTALLATION ...................................................................................................... 15 WINDOWS ME INSTALLATION GUIDE ............................................................................................... 17 WINDOWS ME UNINSTALLATION GUIDE .......................................................................................... 22 WINDOWS XP INSTALLATION GUIDE................................................................................................ 23 WINDOWS XP UN-INSTALLATION GUIDE ......................................................................................... 28 TROUBLE SHOOTING ......................................................................................................................... 31 SPECIFICATIONS................................................................................................................................. 32 WARRANTY INFOMATION .................................................................................................................. 34 CONTACT INFORMATION ................................................................................................................... 36 Release 1.5 ACTiSYS Corporation 2001 3 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual INTRODUCTION This document provides instructions to install the ACT IR220L+/220L/200L Serial-IR dongle along with Windows 98/ME/2000 device driver. It is assumed that the user is familiar with basic operation of Window 98/ME/2000. PACKING LIST When you unpack the package, the following items should be found. 1. 2. ACT-IR220Lplus or ACT-IR220L or ACT-IR200L. User’s Guide SYSTEM REQUIREMENTS To use ACT-IR220L+/220L/220L, your computer MUST meet the following requirements. 1. 2. 3. Window 98/ME/2000. One unoccupied Serial (Rs232) COM port . One unoccupied virtual comport (Com4) BIOS SETUP Verification Before installing the device driver, you MUST setup or verify your BIOS FIRST. Below demonstrates a example of ACT-IR220L+ being installed on Com2. 1. Choose PNP & PCI from BIOS SETUP PNP OS Installed: NO Resource Controlled by: Manual 2. Choose Integrated Peripherals from BIOS SETUP Onboard UART2 Serial Port 2 : 2F8H/IRQ3 Onboard IR function: Disable or UART2: Normal Release 1.5 ACTiSYS Corporation 2001 4 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 98 INSTALLATION GUIDE Precaution: If you have not verified your Bios setup at this point, we strongly recommend you to refer back to the Bios verification section and verify your Bios setup again. Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or occupied by any hardware or any software. We recommend users to completely delete any files or drivers that can interrupt clean fresh installation of our product. Note: You are trying to install a SIR product. Your operating system can always be upgraded to use FIR products. However you can never downgrade from a FIR product to SIR product, therefore verify that you have on previously installed any FIR products on your system. Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a computer system with at least one serial port and Windows 98 already installed. The best choice for the system is a desktop. 1. 2. 3. 4. Connect ACT-IR220L+/200L serial adapter to the COM Port of Desktop PC. Boot up your computer system. Double Click My Computer on DeskTop Double Click Control Panel 5. Double Click Add New Hardware on Control Panel Window. 6. Click Next. 7. Click Next. Release 1.5 ACTiSYS Corporation 2001 5 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 8. Select No, the device isn’t in the list in the box. Then click Next. 9. Highlight Infrared Devices from the Hardware types list, then click Next. 10. Click Next. Release 1.5 ACTiSYS Corporation 2001 6 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 11. From Manufacturers list, choose (Infrared COM port or dongle), from Infrared Devices list, choose (Generic Infrared Serial Port or dongle). Then click OK. 12. Choose ACTiSYS IR-200L if you are a ACT-IR 200L user. Then click Next. 13. Choose ACTiSYS IR-220L/ 220L+ if you are a ACT-IR-220L/ ACT-IR220L+ User. Then click Next. Release 1.5 ACTiSYS Corporation 2001 7 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 14. Select COM port which is physically connected to the Dongle. In most cases, the Dongle is connected to COM2. Choose Communication Port (COM2) from the Port list, click Next. 15. Reboot your computer. Release 1.5 ACTiSYS Corporation 2001 8 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 98 UNINSTALLATION GUIDE 1. 2. 3. 4. Boot up your computer system. Click Control Panel. Double click System Icon Click Device Manager tab. 5. Highlight Infrared Communication Device, and then click Remove. 6. Click OK in the Confirm Device Removal box. Release 1.5 ACTiSYS Corporation 2001 9 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Highlight (Generic Infrared Serial Port or Dongle), then click Remove. 8. Click OK in the Confirm Device Removal. 9. Click on OK to restart your computer. Release 1.5 ACTiSYS Corporation 2001 10 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 2000 INSTALLATION GUIDE Note: If you do not change your computer BIOS setting, STOP here and go to Chapter BIOS SETUP. Note: If your computer system has installed some device on the same com port before, you MUST properly uninstall the devices first. ACT-IR220L+/220L/200L would NOT work with your system any more if the devices are uninstalled improperly because some drivers are still there and cause conflicts with ACT-IR220L+/220L/200L driver. You HAVE to re-install your Windows 2000 again. Note: If your computer system has installed a FIR device before, ACT-IR220L+/220L/200L would NOT work with your system any more. You HAVE to re-install your Windows 2000 again. Note: If you want use Virtual COM Port in your application, STOP here and change IR220L+/IR220L/IR200L to USB-IR Dongle. Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a computer system with at least one serial port and Windows 2000 already installed. The best choice for the system is a desktop. 1. 2. 3. 4. 5. Connect ACT-IR220L+/200L serial adapter to the COM Port of Desktop PC. Startup your computer system Click on Control Panel. Double Click Add/Remove Hardware. On Welcome to the Add/Remove Hardware wizard, click Next>. 6. Choose Add/Troubleshoot a device, then click Next>. You may have to wait a while when the wizard searches for Plug and Play hardware. Release 1.5 ACTiSYS Corporation 2001 11 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Highlight ADD a new drive then click Next. 8. Choose No, I want select the hardware form a list then click OK 9. Select the Infrared device from the Hardware types. Release 1.5 ACTiSYS Corporation 2001 12 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 10. From Manufacturers list, choose ACTiSYS, from Infrared Device list, choose ACTiSYS IR-200L Serial Infrared Device for IR200L; click Next>. 11. Choose ACTiSYS IR-220L Serial Infrared Device for IR220L, click Next>. 12. ACTiSYS IR-220L+ Serial Infrared Device for IR220L+, click Next>. Release 1.5 ACTiSYS Corporation 2001 13 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 13. Click Next>. 14. Choose COM2 in most case, then click Next>. 15. Click Finish. Release 1.5 ACTiSYS Corporation 2001 14 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 2000 UNISTALLATION 1. Startup your computer system. 2. Click on Control Panel. 3. Double click System Icon. 4. Click on Hardware tab, then click Device Manager button. 5. Click on Infrared devices, then highlight ACTiSYS IR-220L+Serial Infrared Device. 6. Click Action and then Uninstall. Release 1.5 ACTiSYS Corporation 2001 15 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. The device has been uninstalled and close device manager, restart your computer. Release 1.5 ACTiSYS Corporation 2001 16 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS ME INSTALLATION GUIDE Precaution: If you have not verified your Bios setup at this point, we strongly recommend you to refer back to the Bios verification section and verify your Bios setup again. Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or occupied by any hardware or any software. We recommend users to completely delete any files or drivers that can interrupt clean fresh installation of our product. Note: You are trying to install a SIR product. Your operating system can always be upgraded to use FIR products. However you can never downgrade from a FIR product to SIR product, therefore verify that you have on previously installed any FIR products on your system. Note: You may experience problems, If you are using a beta version of Windows ME or a old upgrade edition of Windows ME. Some German version of Windows ME has also known to lack virtual Comports. This problem may make are device incapable of communicating with other devices. Following are the instructions to properly install the ACT-IR220L+/220L/200L Dongle. You need a computer system with at least one serial port and Windows ME already installed. The best choice for the system is a desktop. 1. 2. 3. 4. 5. 6. Connect ACT-IR220L+/220L/200L serial adapter to the COM Port of Desktop PC. Boot up your computer system. Double Click My Computer icon on DeskTop Double click Control Panel icon. Double click Add New Hardware icon. On the following boxes, click Next>. 7. Click Next>. Release 1.5 ACTiSYS Corporation 2001 17 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 8. Choose No I want to select the hardware from a list, then click Next>. 9. If you can not find Infrared device from Hardware types list, choose Other devices from the Hardware types list, then click Next >. Otherwise go to step 16. 10. From Manufacturers list, choose (legacy serial infrared device), from Models list, Choose ACT-IR200L Infrared Wireless Interface, then click Next>. 11. Click Finish. Release 1.5 ACTiSYS Corporation 2001 18 All Rights Reserved ACTiSYS Corp. 12. Serial-IR Dongle Installation Manual Double click Add New Hardware icon. 13. Click Next>. 14. Click Next>. 15. Choose No I want select the hardware from list, then click Next>. Release 1.5 ACTiSYS Corporation 2001 19 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 16. Highlight Infrared device from Hardware types list. Then click Next> 17. Click Next>. 18. Click Next> 19. If your device is IR200L, choose ACTiSYS IR200L, click Next>. Release 1.5 ACTiSYS Corporation 2001 20 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 20. If your device is physically connected to COM2, highlight Communications ports (COM2), then click Next>. 21. Click Next>. 22. Click Finish Release 1.5 ACTiSYS Corporation 2001 21 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS ME UNINSTALLATION GUIDE 1. Double click System icon on Control Panel. Panel 2. Go to Device Manager, highlight the items in the Infrared devices, then click Remove button. 3. Highlight the items in the Infrared devices, then click Remove button. 4. Highlight (Generic Infrared Serial Port or dongle), then click Remove button. Click OK button. 5. The device has been successfully uninstalled. Release 1.5 ACTiSYS Corporation 2001 22 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS XP INSTALLATION GUIDE 1. Highlight My Computer, right click 2. Highlight Properties, left click 3. Click Add New Hardware Wizard. Release 1.5 ACTiSYS Corporation 2001 23 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 4. Click Next. 5. Choose Yes, I have already…………….. then click Next>. 6. Wait processing Release 1.5 ACTiSYS Corporation 2001 24 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Choose Add a new hardware device, then click Next>. 8. Choose install the hardware that I manually select from a list (Advanced), then click Next. 9. Choose Infrared devices, then click Next> Release 1.5 ACTiSYS Corporation 2001 25 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 10. Choose respective ACT model, then click Next> 11. Click Next> 12. Choose the Com port which the device physically connected, click Next> Release 1.5 ACTiSYS Corporation 2001 26 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 13. Click Finish Release 1.5 ACTiSYS Corporation 2001 27 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS XP UN-INSTALLATION GUIDE 1. Highlight My Computer, then right click. 2. Highlight Properties, then left click 3. Click Device Manager Release 1.5 ACTiSYS Corporation 2001 28 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 4. Highlight the items under Infrared device, then right click. 5. Click Uninstall 6. Click OK, you have successfully uninstalled the device on your system. Release 1.5 ACTiSYS Corporation 2001 29 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Click OK, you have successfully uninstalled the device on your system. Release 1.5 ACTiSYS Corporation 2001 30 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual TROUBLE SHOOTING For help on general and miscellaneous problems you may be experiencing with your printing, refer to the following pages for possible solutions. Look up your problem and try the solution. SYMPTOM Can not establish link (General) PROBLEM 1. The two IR devices are 1. not aligned properly. 2. 2. Distance is too near or far. 3. 3. The device is inactivated. 4. 4. The device is not installed properly ACT-IR200L/220L+ is The power-saving feature in 1. connected to and takes the notebook computer power only from the either stops or reduces serial port of the power output from the notebook computer. signal lines of the serial port to the ACT-IR200L/220L+ 2. devices. 3. File Transfer between 1. The infrared 1. IR-equipped PDA and communication is ACT-IR device-attached interfered. For example, host computer stops something blocks out 2. before finishing up and the infrared beam or the an error message burst of string light 3. appears. source, etc. 2. Software does not support the IrDA controller chip on the motherboard. 3. Serial port is occupied and not available for IR transmission. 4. 5. Release 1.5 ACTiSYS Corporation 2001 Solution Properly align them again Move one device to a proper distance. Activate it by IR monitor. Refer to Un-installation Guide to remove the device, then reinstall again. Set the “Power Management” control to “Advanced” or “Off” to enable power supplied from computer serial port to ACT-IR200L/220L+ devices. Go to Integrate Peripheral to set the COM port to “Infrared”. Do not install more than one infrared devices on one computer. Check to find out the source of interference and eliminate it before trying again. If you were restoring data, simply try again. If you were doing backup something the PDA does not reset its flags and keeps stopping at the same position unless you press the RESET button once. Be very careful. DO NOT initialize (press ON key and RESET button at the same time) your PDA. Otherwise you may lose all your data. Make proper model # selection in the software as specified in your PC system user`s manual. Make sure to disconnect modem, etc. from the serial port to make it available for IR transmission. 31 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual SPECIFICATIONS Model: ACT-IR220L+/ACT-IR220L/ACT-IR200L Carrier: Infrared radiation (peak wavelength: 850 to 1050nm) Sub-Carrier: 500 KHz for SHARP ASK-IR and ASK(37KHz) for TV remote spec.(IR200L only) Communication Distance: IR200L From 0 cm to 80 cm. For best results, from 20 cm (7.9in) to 60 cm (1 ft. 11.6 in) IR220L From0 cm to 250 cm. For best results, from10 cm (3.95 in) to 150 cm (4 ft. 11.05 in) SHARP ASK-IR: Baudrate: Parity Bit: Data: Stop Bit: Error Check: 9600 bps to 38.4K bps (IR200L only) Odd 8 bit 1 bit Check Sum IrDA-IR: Baudrate: Parity Bit: Data: Stop Bit: Error Check: 9.6,19.2,(38.4),57.6,115.2K bps (IR200L/220L+) None 8 bit 1 bit CRC Serial Interface: Cable Interface (to host computer) Signal Level: RS-232 Standards Connector: DB-9 female connector Power Source: PC RS-232 Serial Port Power Consumption: 0.30mW (11mA max.) Operating temperature: 0oC to 40oC (32oF to 104oF) Dimensions (Inches): 2.0”L x 1.63”W x 0.62”H 51mm x 41mm x 16mm Weight: 2.0 oz (54 gr.) Accessories: User Manual Optional Accessories: DB9/DB25 Converter Windows 95/98/ME/2000: IR Software Release 1.5 ACTiSYS Corporation 2001 32 All Rights Reserved ACTiSYS Corp. Pin Assignments: Pin 2 3 4 5 7 8 Serial-IR Dongle Installation Manual Serial Interface DB9 female connector Name Receive Data Transmit Data Data Terminal Ready Signal Ground Request to send Clear to send Release 1.5 ACTiSYS Corporation 2001 Symbol RXD TXD DTR GND RTS CTS I/O I O O O I Function Input signal Output signal For data link to build up and maintain Reference ground (0V) for all signals Output signal from host computer Input signal to host computer 33 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WARRANTY INFOMATION THE FOLLOWING WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. ACTiSYS Corporation warrants to the first consumer purchaser, for a period of one year from the date of purchase, that this wireless interface (“the Product”) will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof at no charge to the purchaser for parts or for labor. This warranty does not apply to any appearance items of the Product, any consumable items such as paper, ink ribbon, or batteries supplied with the Product, or to any equipment or any hardware, software, firmware, or peripheral other than the Product. This warranty does not apply to any Product the exterior of which has been damaged or defected, which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design, construction or interfacing. Tampering With Label Voids Warranty. In order to enforce the rights under this limited warranty, the purchaser should mail, ship, or carry the Product, together with proof of purchase, to ACTiSYS. The limited warranty described above is in addition to whatever implied warranties may be granted to purchasers by law. To the extent permitted by applicable law, ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR USE ARE LIMITED TO A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties beyond the time period described above on behalf of ACTiSYS Corporation. The warranties described above shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described above, shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall ACTiSYS Corporation be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than ACTiSYS technician. Nor shall ACTiSYS Corporation be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply for you. Release 1.5 ACTiSYS Corporation 2001 34 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual ACTiSYS Corporation warrants to the first consumer purchaser, for a period of 1 year from the date of purchase, that this wireless interface (The Product? Will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof at no charge to the purchaser for parts or for labor. This warranty does not apply to any appearance items of the Product, any consumable items such as paper, ink ribbon, or batteries supplied with the Product, or to any equipment or any hardware, software, firmware, or peripheral other than the Product. This warranty does not apply to any Product the exterior of which has been damaged or defected, which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design, construction or interfacing. Tampering With Label Voids Warranty. In order to enforce the rights under this limited warranty, the purchaser should mail, ship, or carry the Product, together with proof of purchase, to ACTiSYS . The limited warranty described above is in addition to whatever implied warranties may be granted to purchasers by law. To the extent permitted by applicable law, ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR USE ARE LIMITED TO A PERIOD OF 1 YEAR FROM THE DATE OF PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties beyond the time period described above on behalf of ACTiSYS Corporation. The warranties described above shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described above, shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall ACTiSYS Corporation be liable or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than ACTiSYS technician. Nor shall ACTiSYS Corporation be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Release 1.5 ACTiSYS Corporation 2001 35 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual CONTACT INFORMATION ACTiSYS Corporation. 48511 Warm Springs Blvd, Suite 206 Fremont, CA 94539, USA TEL: (510) 490-8024, FAX: (510) 623-7268 E-Mail: irda-support@actisys.com Web: www.actisys.com Release 1.5 ACTiSYS Corporation 2001 36 All Rights Reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:08:20 09:54:45 Producer : Acrobat Distiller 4.05 for Windows Modify Date : 2002:08:20 09:55:57+08:00 Page Count : 36EXIF Metadata provided by EXIF.tools