Acumen Technologies 1J05 350MHz Gas Fireplace Remote Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	548590
Application ID	GPgOdEbJtfRNwPwgr8eSLQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.6kB (195058 bits)
Date Submitted	2005-06-04 00:00:00
Date Available	2005-06-04 00:00:00
Creation Date	2005-03-12 15:03:04
Document Lastmod	0000-00-00 00:00:00
Document Title	User Manual
Document Creator	HP 9100C Digital Sender
Document Author:	BEN HO

AC MEN
Acumen Model J
Fireplace Remote Control
Installation and Operation Instructions:
The Acumen Model J Remote Control is designed for use with decorative gas fireplace and wall heaters using
SIT 820 Nova gas valve.
The Model J Transmitter is a two-button hand held transmitter, which turn the gas on/off. The display of the
transmitter shows the current room temperature and low battery indicator.
Installation Precautions:
The Model J Remote Control is tested safe when installed in accordance with this installation manual. It is
your responsibility to read all instruction before starting installation and to follow these instructions carefully
during installation.
The Model J Remote Control MUST be installed by a qualified service technician.
The Model J Remote Control is carefully engineered and MUST be installed only as specified. If you modify it
or any of its components, you may possibly cause a fire hazard.
FCC Requirements
WARNING: Changes or modifications to this unit not expresslyapproved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 to the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications,
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined byturning the
equipment off and on. the user is encouraged to try to correct the interference by one or more of the following
measures:
A Reorient or relocate the receiver antenna.
, Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio TV technician for help.
Canadian Equipment Requirements
This digital apparatus does not exceed the (class A/Class B)‘ limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications, Le
present appareil numerique n met pas de bruits radioelectriques depassant Ies Iimites applicables aux
appareils numeriques (de la class A/de Ia class B)‘ prescrites dans Ie Reglement sur Ie brouillage
radioelectrique edicte par Ie ministere des Communications du Canada,
This device complies with RSs-210 of Industry Canada, Operation is subject to the following two conditions :
(1) this device may not cause interference. and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the
National Electirc Code ANSI/NFPA No. 70-current (In the United States), or with the current CSA 022.1
Canadian Elecfirc Code (in Canada).
1.0Inshllation Instruction
1.1 Installing the Receiver
WARNING: TURN ELECTRICAL POWER OFF AT THE CIRCUIT BEAKER BEFORE BEGINNING THIS
INSTALLATION.
1. Make sure the slide switch on the Remote Receiver is at the OFF position. See Figure 1.
Remote
Recelver
MIIIivoIt Generator
Figure 1 Figure 2
2. Connect the leads to the millivolt generator and the main burner to the output cable of the Remote
Receiver as shown in Figure 2.
3. Installlng the Remote Receiver to a Wall Mount:
— Secure the Remote Reoeiver to the wall mount.
— Use the screws provided to secure the face blade to the Remote Receiver. See Figure 4.
Installation of the Receiver
to a Junction Box
Figure 3 Figure 4
4. Installlng the Remote Receiver to a Fireplace:
7 Secure the Fireplace Mounting plate to the base pan of the fireplace.
— Slide the Remote Receiver into the fireplace mounting plate. See Figure 4.
Heat Shield
Figure 5 Figure 6
5. Put the switch cap to the slide switch.
6. Slide the battery compartment into the Remote Receiver. See Figure 5.
7. In order to prevent the Remote Receiver (fireplace installation only) from overheating, put a heat shield
(option item) above the Remote Receiver. See Figure 6.
2.0 Operation Instructions:
2.1 Transmitter Operation
A. Flame OnIOff
1. Press the On button once to turn on the fireplace.
2. Press the Off button once to turn off the fireplace.
3. The fireplace will automatic turn off after 6 hours.
WARNING: IT TAKES SOME TIME FOR THE RECEIVER TO RESPOND TO THE TRANSMITTERDO NOT
PRESS THE MANUAL AND I OR AUTO ONIOFF BUTTONS MORE THAN ONCE WITH 2 SECONDS FOR
CORRECT OPERATION.
B. Child-Proof Function :
1. Remove the cover at the back of the Remote Transmitter to expose the CHILD-PROOF switch.
2. Slide the CHILD-PROOF switch to position marked C/P to activate the CHILD-PROOF function
“Child-Proof *" will appear on the LCD. See Fig 7.
3. In CHILD-PROOF the Remote Transmitter will not operate the Remote Receiver until the “child-proof"
code is used or the switch is returned to the other position.
4. Press the Off button in the following sequence, Long-Short—short-Long-Short will temporarily restore
button function. “Child-Proof" will disappear from the LCD. (Long is pressing button for longer than 0.5
second and Short is pressing the button shorter than 0.5 second.)
5. If no button is pressed within 2 minutes. the Remote Transmitter will return to Child-Proof function and
""Child-Proof“’ will reappear on the LCD until the Child-Proof switch is slide back to the other position.
C. °Fl°C Selection
1. Press and hold the Off button for longer than 4 seconds. The °F or °C display will blink.
2, Press the Off button to select temperature display in “F or °C.
3. The LCD will show the room temperature about 16 seconds aftenNard.
2.2 Receiver Operation
The Remote Receiver has 2 operation modes. They are On and Remote modes.
A. On Mode
1. In the On mode the Receiver will turn on the fireplace,
2. The Receiver will not respond to the Transmitter and turn the fireplace on and off.
B. Remote Mode
1. The Receiver will respond to the Transmitter and turn the fireplace on and off.
2.3 Changing Batteries
1. Slide the slide switch to Off position.
2. Press the battery compartment slightly into the Remote Receiver and then release. The battery
compartment will pop out of the Remote Receiver.
3. Slide open the battery door and replace batteries.
4. Replace the battery door and slide the battery compartment back into the Remote Receiver.
2.4 Batteries
1. The Remote Transmitter uses 3 AAA-size batteries. Replace these batteries at least every 6 months or
when the Low battery indicator on the LCD is on.
2. After you take out the batteries. wait for at least 1 minute before putting fresh batteries into the Remote
Transmitter.
3. Use fresh alkaline batteries only.
3.0 IMPORTANT SAFETY FEATURE:
You can set a private code into your system to prevent accidental operation by another transmitter nearby.
See Figure 7.
3.1 Coding Instructions:
1.
2.
3.
sn.»
909°
Remove the cover on the back of the Remote Transmitter to expose the code switches. Slide the code
switches to you choice of ON or OFF positions. FACTORY SETTING IS ALL "OFF".
Make sure the slide switch on the Remote Receiver is at OFF position.
Take the Remote Transmitter close to the fireplace or the Remote Receiver (less than 5 feet from the
fireplace or Remote Receiver is recommended.)
Slide the slide switch on the Remote Receiver to ON position
Install fresh AAA alkaline batteries into the Remote Transmitter. The LCD on the Remote Transmitter will
blink.
Press a button on the Remote Transmitter. The Remote Receiver will produce a ‘beep' sound when it
receives the code trom the Remote Transmitter.
If you do not hear a ‘beep’ sound from the Remote Receiver, removes batteries from the Remote
Transmitter and slide the slide switch on the Remote Receiver to OFF position, wait for 1 minute, and
repeat step 3 to 6.
Replace the cover of the Remote Transmitter and the Receiver. The system is now ready to operate.
If you desire to operate multiple Remote Receivers with the one Remote Transmitter. continue to hold
the button on the Remote Transmitter as you bring the Remote Transmitter within 5 feet of each Remote
Receiver then slide the switch on the Remote Receivers to ON position. Each will acknowledge receipt
of coding with a beep.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 4
Creator                         : HP 9100C Digital Sender
Create Date                     : 2005:03:12 15:03:04
Author                          : BEN HO
Producer                        : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools