Adams Rite 8400 Mortise Exit Device Installation Instructions 80 0180 38 H

User Manual: Adams Rite 8400 Mortise Exit Device Installation Instructions Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 2

80-0180-38, Revision H
Backset
Door Opening Width
30”
36”
42”
48”
Dimension A
31/32” or
1-1/8”
26.84
32.84
38.84
44.84
1-1/2”
25.57
31.57
37.57
43.57
8400 Mortise Exit Device
Installation Instructions
Phoenix, AZ 85044
Tel: 1-800-872-3267
Mon-Fri: 6:00am - 4:00pm PDT
Fax: 1-800-232-7329
www.adamsrite.com
Preparing
NOTE 1: These dimensions and templates assume
a door thickness or 1-3/4.” For doors of other
thickness, the factory should be consulted.
NOTE 2: CL* denotes vertical centerline of
strike within 1/64” of deadlatch
centerline.
Mounting the Push Bar
1. DEPRESS latch bolt.
NOTE: The square key on plug must align with square notch on side
plate.
2. INSERT bar assembly cam plug thru side plate.
3. INSTALL self-tapping screws on both ends and securely TIGHTEN.
4. TIGHTEN cam plug set screw.
5. INSTALL faceplate.
6. INSTALL end caps (dogging socket at latch end).
Installing the Deadlatch
1. ADJUST mounting post to length required
to flush faceplate with nose of stile.
2. TIGHTEN lock case securely using #10-32
screws.
IMPORTANT NOTE
Installation must be in accordance to all applicable building and life safety codes.
80-0180-38, Revision H
Adams Rite is a brand associated with Hanchett Entry Systems, Inc., an
ASSA ABLOY Group company. Copyright © 2016, Hanchett Entry Systems, Inc.
All rights reserved. Reproduction in whole or in part without the express written
permission of Hanchett Entry Systems, Inc. is prohibited.
Separating Push Bar and Mounting Bar
1. REMOVE both end caps (retainer is attached to nose end cap).
2. SLIDE push bar toward hinge side of door.
3. CONTINUE to slide push bar past the pivot plate that rides in
push bar track.
4. SLIDE push bar in opposite direction, keeping pivot plate out of
track until push bar is free of mounting bar.
Installing Push Bar to Mounting Bar
1. With push bar in hand and mounting bar attached to door, FIND
the stop plate staked into push bar (plate is on the latch end of
the assembled unit).
2. SLIDE the pivot plate nearest the hinge into track of push bar
until second pivot plate is exposed.
3. INSERT pivot plate into track on push bar and SLIDE in
opposite direction until push bar and mounting bar align.
Cutting Off for Non-Standard Doors
1. DRIVE OUT the two roll pins.
2. REMOVE mounting cap.
3. COLLAPSE bar and TAPE DOWN in area of cut-off.
NOTE: 3-19/32” [91.3 mm] minimum dimension from rivet centerline to new cut-
off length, as show below.
4. DETERMINE extrusion length (Dimension “B”).
5. MEASURE mounting bar (not push bar), and MARK extrusion length on tape.
6. SAW off excess length.
7. LAY mounting clip over mounting bar (Figure “C”) and USE as a guide to drill
two 1/8” [3.2 mm] holes.
8. RE-INSTALL mounting cap into mounting bar and DRIVE two roll pins into
holes.
9. SEE installation instructions.
Changing Hand of Exit Device
1. REMOVE screws and then spring retainer plate.
2. REMOVE two springs.
3. REMOVE auxiliary bolt.
4. REMOVE latch bolt and deadlocking arm assembly, being careful
not to lose small internal spring.
5. REMOVE internal (deadlocking) spring.
6. SLIDE pin out of latch bolt and REMOVE deadlocking arm.
7. REPLACE deadlocking arm on opposite side of latch bolt and
INSTALL pin.
8. INSTALL internal spring and INSERT latch bolt and deadlocking arm
assembly into latch case.
9. INSTALL auxiliary bolt.
10. REPLACE two springs.
11. INSTALL spring retainer plate.
Front View
1. REMOVE link from crank arm.
2. ROTATE crank to opposite
direction.
3. CONTINUE moving crank arm as
as bar is released.
Back View
1. REMOVE Cam screw.
2. FLIP Cam over to opposite
position.
3. REPLACE Cam screw and
TORQUE to 6.5–7.0 inch pounds.
IMPORTANT NOTE
Installation must be in accordance to all applicable building and life safety codes.

Navigation menu