Ademco 51373SL Wireless Door Chime Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	918097
Application ID	MxfETuAL7bCsUGvq2/7Akg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	250.16kB (3127021 bits)
Date Submitted	2008-03-22 00:00:00
Date Available	2008-03-22 00:00:00
Creation Date	2008-03-18 09:24:16
Producing Software	Adobe Acrobat 7.08 Image Conversion Plug-in
Document Lastmod	2008-03-18 09:26:04
Document Title	Users Manual
Document Creator	Adobe Acrobat 7.08

Plug-In Wireless Chime & Push
with Flashing Light
Please retain these instructions for future reference.
Pack Contents
0 Bell Push
° 100 ft. door chime
- 2 screws. wall anchors, adhesive pad
- 23A 12V Alkaline battery for the push
You Will Require
0 Small flat blade screwdriver
0 Small cross head screwdriver
Safety
Always follow the manufacturer's advice when using power
tools and wear suitable protective equipment (eg. safety gog-
gles) when drilling holes.
Set Up The Bell Push
1. Open the bell push unit.
Carefully insert a small flathead screw- fl
driver into slot A and twist gently Lift
away the front of the bell push to reveal \
the inside.
2. Set the bell push channel.
It is possible that your chime may be
set off by a nearby wireless device.
This could be a neighbor's bell push.
for example. To prevent this interfer-
ence, you may need to change to
another “channel". Using a flat blade
screwdriver, set rotary switch B to
another position. 1 to 16. Make a note of the
channel setting. Your chime will need to have
its switch set to the same position — see Set Up
The Chime.
3. Select a tune.
Switch C. in the bell push. selects the chime ——
tune:
1=Westminster
2=Ding Dong (manufacturer's setting)
3=Ding
Mounting The Bell Push
Mount the bell push using the adhesive pad or by using the two
screws. as follows:
1. Hold the bell push up against the door frame or wall where
you want to mount it. (Ensure the push button is at the top).
2. Make a mark on the wall where the two screw holes ‘~
will be.
3. Take away the bell push base and drill two
holes, large enough to accommodate the
wall plugs if necessary.
4. Screw the bell push to the wall through
the mounting points D.
5. Insert the 12V 23A battery (included).
6. Refit the cover. locating the top catch first.
Set Up The Chime
1. Set the chime channel. Set rotary switch E on the chime to
position 1 to 16, as with the bell push. The channel set on
the chime must match the channel already
set on the bell push in Set Up The Bell Push.
Test Your Door Chime
Test your wirefree door chime at the desired location in a
receptacle.
1. Press the bell push.
2. The chime should sound.
Check the Troubleshooting section if the chime does not sound.
Troubleshooting
Chime doesn't sound when the bell push is pushed
- Check that the push battery has enough charge and is installed
the right way. Note the + and - symbols molded into the back
of the battery compartment.
- Check that the bell push channel switch and the chime channel
switch are in the same position. See Set Up.
0 Check that the distance between the bell push or the chime is
not too great‘ (see front of pack).
_ Chime sounds without being pushed
- Check that there is not water in the bell push or the chime.
This can damage the electronics.
0 Check that a neighbor is not using the same channel for their
chime or a similar wireless system. See Set Up.
'The stated transmission range if this product is measured in
open field conditions. Walls. ceilings and metal structures (i.e.
reinforced uPVC) will reduce the maximum range.
Disposal and Recycling
Batteries and waste electrical products should not be disposed of
with household waste. Please recycle where these facilities exist.
Check with your local authority or retailer for recycling advice.
Guarantee
Honeywell guarantees this product for 1 year from the date of
purchase. Proof of purchase is required: this does not affect
your statutory rights. If you require further information about your
product, call the Honeywell helpline at 1-800-468-1502.
Declaration
Honeywell hereby declares that this product complies with Part
15 of the FCC rules and Industrial Canada standards. This device
operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may
cause undesired operation.
Caution: Changes or modifications not expressly approved by the
party responsible for regulatory compliance could void the users
authority to operate the equipment.
Design reg. UK3015090,3015344:
EU 180823176672:
China ZL200430006524.9, ZL2004300503012 0 us
Federal
F© Communications ”STE“
Commission
httpzllyourhomehoneywollcom
Operating frequency: 345 MHz; 1-800-468—1502
FCC and |C certified 1-Year Limited Warranty
Frequence de service : 345 MHz 68mm"? "ml“ “8 ‘ 3“
Certifié FCC et IC
I aim de garantia limitada
32007 Honeywell International Inc.
All Rights Reserved.
Golden Valley. MN 55422 USA.
Engineered by Honeywell
Made in China
Tails dro'ts reserves
Congo par Hanan: nil 0
Fab/1m“? en Chine
85267 33434 1
Proof of Purchase/Preuve d'achatl
‘ . . . . Comprobante de compra
H; . Model’Mod‘ele/Modelo RCWLIOSAI003
.. r. g» 69-21l6EFS
bSll
Instnlctions for wireless plug-in door chime Product #51373SL!
1. Open the cover of the pushbuttou with a flat screwdriver, A gentle twisting will remove the cover of
the pushbuttonr
24 Insert the supplied 1 X A23 batteries in the pushbutton, observe polarity, negative end is resting on
the spring.
3. Locate a good position for the pushbutton next to the doom Do not mount on or next to a metal
surface. Drill two 476mm holes and insert the wall plugs. Place the back plate in the right position
and tighten the plate on wall with the screws supplied.
4. Position the pushbutton over the back plate so that the lip on the back plate engages into the slot.
Make sure the rubber gasket is properly seated. Firmly press the pushbutton until it snaps over the
back plate.
5. Plug the chime receiver into a 110/ 120V AC mains socket. Press the button on the pushbutton within
100 feet range and the plug~in (low chime will sound and LED will flash
6‘ There are 16 different house codes provided. They are factory preset to position ll lf experience of
interference in your area. you can change the house code on both the receiver and pushbutton.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2008:03:18 09:26:04+08:00
Create Date                     : 2008:03:18 09:24:16+08:00
Metadata Date                   : 2008:03:18 09:26:04+08:00
Creator Tool                    : Adobe Acrobat 7.08
Format                          : application/pdf
Document ID                     : uuid:7541c833-0d75-44ec-861d-71ee1edf01b3
Instance ID                     : uuid:aa32fa83-1da8-44bd-ace3-c272e8e09acd
Producer                        : Adobe Acrobat 7.08 Image Conversion Plug-in
Has XFA                         : No
Page Count                      : 2
Creator                         : Adobe Acrobat 7.08

EXIF Metadata provided by EXIF.tools