Ademco 8DL5800TM-1 security transmitter User Manual N6716V2 RevD

Download:
Mirror Download [FCC.gov]
Document ID	581102
Application ID	wMx8Y5tjm7KY/Jchg1KKJA==
Document Description	II with FCC Part 15 Statment
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.74kB (46728 bits)
Date Submitted	2005-09-13 00:00:00
Date Available	2005-10-12 00:00:00
Creation Date	2005-09-12 17:19:15
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-09-12 17:21:50
Document Title	Microsoft Word - N6716V2_RevD.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	E650365

ADEMCO 5800TM
TRANSMITTER MODULE
Used with Bidirectional Wireless Devices
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5800TM Transmitter Module is designed to be used in conjunction with one or more wireless
bidirectional devices. The 5800TM is compatible with any control panel that is also equipped with a
5800 Series RF receiver. It complements the RF receiver in that it transmits the information to be
displayed on, or sounded by a wireless bidirectional keypad. No modification to the control panel is
necessary. Connections are made directly to the control panel’s keypad connection points, as
described below. See the installation instructions that accompany the 5800 Series wireless
bidirectional keypad for complete operating information for the 5800TM/keypadcombination.
INSTALLATION
Observe the same precautions in selecting a location for the 5800TM as for the system’s RF
receiver, to insure good transmission and reception. The 5800TM must be located next to the
system’s receiver (between one and two feet from the receiver’s antennas).
Do not install the 5800TM within the system control panel cabinet; mount it remotely, on its
accompanying mounting bracket. The bracket is easily installable via two countersunk mounting
holes. Keyhole slots on the rear of the 5800TM slip onto two hooks on the mounting bracket.
PROGRAMMING For an Addressable System:
1. Select one of the following addresses for the 5800TM by removing its cover, and cutting the
appropriate
jumper(s) on its circuit board, as follows:
2. Program the control panel, by assigning the address selected above to one of the wired consoles
in the
system.
FOR ADDRESS
28
29
30
CUT
JUMPER(S)
RED (W 1)
WHITE (W 2)
BOTH
Note: For those controls requiring device programming (in ✱93 mode), program this device as an
“Alpha Console.”
For a Non-Addressable System: No programming is required.
WIRING CONNECTIONS Connect the 5800TM to the control panel’s remote keypad connection
points, using the supplied connector with flying leads. Wire colors and functions match those for
keypads:
RED +12VDC (Aux Power)
GREEN: Data to Control Panel
YELLOW : Data from Control Panel
BLACK: Ground (–)
BLUE: Not used
SPECIFICATIONS
Physical: 2-1/4”W x 4-1/8”H x 7/8”D (57mm x 105mm x 22mm)
Electrical: Voltage: +12VDC (from control panel remote keypad connection points) Current: 20mA
LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom Electronics business
("Seller") 165 Eileen W ay, Syosset, New York 11791, warrants its product(s) to be in
conformance with its own plans and specifications and to be free from defects in materials and
workmanship under normal use and service for 24 months from the date stamp control on the
product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of
original purchase unless the installation instructions or catalog sets forth a shorter period, in
which case the shorter period shall apply. Seller's obligation shall be limited to repairing or
replacing, at its option, free of charge for materials or labor, any product(s) which is proved not
in compliance with Seller's specifications or proves defective in materials or workmanship under
normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise
if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell
factory service. For warranty service, return product(s) transportation prepaid, to Honeywell
Factory Service, 165 Eileen W ay, Syosset, New York 11791. THERE ARE NO WARRANTIES,
EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR
PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY W
HATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OW N
NEGLIGENCE OR FAULT. Seller does not represent that the product(s) it sells may not be
compromised or circumvented; that the product(s) will prevent any personal injury or property
loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide
adequate warning or protection. Customer understands that a properly installed and maintained
alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring
without providing an alarm, but it is not insurance or a guarantee that such will not occur or that
there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL
HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER
LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING.
HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR
ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE,
REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN
ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), W HICH SHALL BE
THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any
previous warranties and is the only warranty made by Seller on this product(s). No increase or
alteration, written or verbal, of the obligations of this Limited Warranty is authorized.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL W ITH
WHICH THIS DEVICE IS USED, FOR DETAILS ON LIMITATIONS OF THE ENTIRE
ALARM SYSTEM.
FCC STATEMENT
FCC ID: CFS8DL5800TM-1
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference (2)
This device must accept any interference received, including interference that may
cause undesired operation.
IC: 573F-5800TM-1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d93aa78c-6753-4883-a9b6-9079938e9347
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2005:09:12 17:19:15-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2005:09:12 17:21:50-04:00
Metadata Date                   : 2005:09:12 17:21:50-04:00
Document ID                     : uuid:ce83fa80-53e1-4680-88d6-47905c245c2d
Format                          : application/pdf
Title                           : Microsoft Word - N6716V2_RevD.doc
Creator                         : E650365
Author                          : E650365

EXIF Metadata provided by EXIF.tools