Ademco 8DL5805-6A Wireless Key Transmitter User Manual K5761bx

Download:
Mirror Download [FCC.gov]
Document ID	740453
Application ID	f6RSpaOrABDfbXnzytQkeg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.38kB (142231 bits)
Date Submitted	2006-12-20 00:00:00
Date Available	2006-12-22 00:00:00
Creation Date	2005-04-29 13:29:24
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2006-12-19 17:33:44
Document Title	Microsoft Word - K5761bx.doc
Document Creator	PScript5.dll Version 5.2

K5761bx 5/05 Rev. A
5805-6A
WIRELESS KEY TRANSMITTER
USER GUIDE
OPERATING THE BUTTONS
Activating a Button
To activate a programmed function on the
button, press and hold the button(s) down
until the LED flashes, and then release it.
The LED will emit a green flash to indicate it
has transmitted in Standard mode or a red
flash to indicate it has transmitted in HighSecurity mode. The LED will not flash during
transmission if the battery is low.
Note:
In order to minimize the possibility of accidental
transmissions, the buttons on the 5805-6 must be
pressed and held for at least 1/2 second to activate the
transmitter.
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
ON
OFF
SERIAL #1
LOOP 2
LOW BATTERY INDICATION
When a Button is pressed and a Low Battery
condition exists, a message is transmitted to
the control panel and LOW BAT will be
displayed on the keypad.
Improper
result in
battery.
installation
damage to
will
the
Replacing The Battery
1. Remove the case back by using the blade
of a small screwdriver to pry it open.
2. Carefully remove the battery.
3. Insert a new battery in case back location
as shown in Figure 2. Negative (-) end
must face down. Use Maxell CR2032,
Duracell DL 20325,
lithium battery only.
or
Varta CR2032
4. Close the case by snapping case front and
back together.
INSERT THIS
END FIRST
SERIAL #1
LOOP 1
BA
TT
(+) RY
GENERAL INFORMATION
The 5805-6A is a compact, 6-button portable
wireless transmitter that permits an alarm
system to be controlled remotely. The
transmitter is typically used for arming,
disarming, panic and output relay operation.
Check with your installer for operation of the
buttons on your unit.
NOTE
NEGATIVE (-) SIDE
MUST FACE DOWN
SERIAL #2
LOOP 2
SERIAL #2
LOOP 3
5805-6 TRANSMITTER*
*SERIAL #2 - LOOP 1 = ON + 4
LOOP 4 = 3 + 4
5805-007-V0
5805-008-V0
Figure 1 - 5805-6 Button Designations
Figure 2 - Replacing the Battery
Table 1 - Transmitter Functions
(Complete this table with your installer)
Button
Function
ON
OFF
ON + 4
3+4
Do not remove the Printed
Circuit Board.
LIMITATIONS STATEMENT
Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach
the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage
can occur if a metal object somehow blocks the signal path.
Wireless button type transmitters that have visual and audible indications of status must be used to
confirm that the desired action (such as arming) has occurred after pressing a function button on any
of these transmitters. Be sure to listen for appropriate audible and visual indications that such action
has occurred. Otherwise, you could inadvertently leave yourself or your premises unprotected.
External factors such as humidity, high or low temperatures, or constant activation of a programmed
button may reduce battery life in a given installation. If the button unit is used infrequently, activate
it regularly (once per week) to confirm operation. A button type transmitter will report a low battery
condition to the alarm control when a low battery status is detected.Changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE
ALARM SYSTEM, REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
FCC ID: CFS8DL5805-6A
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
IC: 573F-58056A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5ae0a1dc-ef4c-4eb8-9795-25d33df3fb04
Producer                        : Acrobat Distiller 4.05 for Windows
Create Date                     : 2005:04:29 13:29:24Z
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2006:12:19 17:33:44-05:00
Metadata Date                   : 2006:12:19 17:33:44-05:00
Document ID                     : uuid:843357ab-2125-4e22-a328-627e09676924
Format                          : application/pdf
Title                           : Microsoft Word - K5761bx.doc
Creator                         : PScript5.dll Version 5.2

EXIF Metadata provided by EXIF.tools