Ademco 8DL5822T Tilt Sensor Transmitter User Manual 800 10946 A 5822T IIs 9 4 12
Honeywell International Inc. Tilt Sensor Transmitter 800 10946 A 5822T IIs 9 4 12
Ademco >
Users Manual
5822T Tilt Sensor Transmitter - Installation Instructions
1. OPEN THE
SENSOR
2. CONNECT
THE BATTERY
• Observe correct
polarity;
• DO NOT touch
the Tilt Sensor.
3. ENROLL THE SENSOR
Enroll the sensor in the control panel. Refer to the control
panel instructions for programming details. Program the
sensor as an “RF” type (supervised RF) device.
Sensor loops:
Loop 1 Terminals (Input 1), for use with a wired normally-
closed contact
Loop 2 Tilt Sensor
Either or both loops can be used.
To enroll Loop 1, open and close the magnet connection
(align the magnet with the sensor, move it at least 1” away and
back) two times.
To enroll the Loop 2, hold the sensor vertically (arrow UP), tilt
to horizontal position and back to vertical position two times.
5822T-003-V0
4. MOUNT THE SENSOR
Before permanently mounting the sensor, conduct Go/No
Go tests (see control panel manual) to verify adequate
signal strength. Relocate the sensor if necessary.
• Use the double-sided tape (supplied) to mount the
sensor.
• Optional screws (supplied) are recommended. Mounting
screws must be used in installations where temperatures
drop to freezing 32° F (0° C).
For Tilt Sensor: Mount with the arrow pointing UP.
For Terminals Installation: Use a wired normally-closed
contact. Feed wires through one of the concealed wiring holes
or "breakout" areas.
Double-sided
Tape Mounting
Screws (2)
Cover
Screw
Magnet
Front
Cover
Back
Cover
1/2” or less
Mounting
Surface
5822T-002-V0
Alignment
Marks
SPECIFICATIONS
Battery*: (included)
1 x 3 V, Lithium;
Panasonic CR123A, Duracell DL123,
Duracell DL123A, or Honeywell 466
Operating Temperature: -4° to +131° F (-20° to +55° C)
Relative Humidity: 95% max. (non-condensing)
Dimensions: 1-9/16" W x 3-1/16" H x 1-3/16" D
(40mm x 78mm x 30mm)
* Battery Caution: Risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 212° F (100° C), or incinerate. Dispose of used
batteries promptly. Keep away from children.
APPROVALS / LISTINGS
• FCC part 15, Class B verified COMPLIANCE NOTES
• IC, ICES-003, Class B verified Product must be tested at least
once each year.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User Manual. Unauthorized changes or modifications could void the user's authority to
operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC
requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in
strict accordance with the manufacturer's instructions, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class B computing device in
accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different
branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT:
This device complies with Part 15 of the FCC Rules, and RSS 210 of Industry Canada (IC). Operation is
subject to the following two conditions: (1) This device may not cause harmful interference (2) This device
must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences
nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une
reception indésirable.
Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the
properties of their respective owners. All rights reserved. Assembled in Mexico.
For the latest U.S. warranty information, please visit: www.honeywell.com/security/hsc/resources/wa or
Please contact your local authorized Honeywell representative for product warranty information.
Ê800
-
10946OŠ
P/N 800-10946 Rev A 9/12
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2012 Honeywell International Inc.
www.hone
y
well.com/securit
y
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
WITH WHICH THIS DEVICE IS USED FOR DETAILS REGARDING LIMITATIONS
OF THE ENTIRE ALARM SYSTEM.
Tilt
Sensor
Tamper
Switch
Battery
INSIDE
VIEW
Reed
Switch
Back
Cover
1
2
3
5822T-001-V0
PLEASE GO TO LOWER RIGHT
HAND CORNER FOR FCC / IC
AGENCY STATEMENTS.