Ademco 8DL5878-1 Wireless Wall Transmitter User Manual

Honeywell International Inc. Wireless Wall Transmitter Users Manual

Users Manual

K14347 4/06 Rev. A - ADEMCO 5878Wireless Wall TransmitterINSTALLATION AND SETUP GUIDE GENERAL INFORMATION The 5878 is a compact, six-button, eight-loop wall mountable wireless transmitter intended for use only with wireless alarm systems that support 5800 series receivers. Individual buttons on the transmitter may be programmed for any zone response, but are typically used for arming/disarming and for home automation functions. Optional function buttons are provided with the 5878. Do not use for system disarming in an area that requires security. This device supports both Standard and High-Security (encrypted) modes. The latter sends rolling-code encrypted messaging to the RF receiver. This device must be used with a receiver or control that supports high security mode i.e.: 5881EN, 5883, 6150RF, or 6160RF receiver or a LYNXR Series control panel (Revision 13 or higher if you intend to use it in high security mode). The 5878 is powered by one replaceable lithium battery de-signed to provide up to four years of life. For battery installation, see Replacing the Battery. 5878-001-V1SERIAL #1LOOP 3SERIAL #2LOOP 3SERIAL #1LOOP 4LEDSERIAL #1LOOP 2SERIAL #2LOOP 2SERIAL #1LOOP 1STAYAWAY12345878 WALL TRANSMITTER** SERIAL #2 - LOOP 1 = AWAY + 4 BUTTONLOOP 4 = 3 + 4 BUTTONS Figure 1 - 5878 Button Designations PROGRAMMING The 5878 is assigned two unique serial numbers during manufacture and each button, or button combination on the unit also has a distinct "loop" number (refer to Figure 1) that must be programmed into the control panel during installation. Assign each button, or button combination, to one of eight individual zones and designate the Input Type as "BR" (Button Type RF). 1. When prompted, enter the serial number either by: Pressing and releasing the button (or buttons) that you are programming twice (wait about 5 seconds between button activations).or Manually through the keypad. Notes: (1) To activate the transmitter, the 5878 buttons must be pressed and held for at least one-half second. (2) Serial #2 is one (1) digit higher than serial #1, which is printed on the rear of the transmitter. Loop 4 Setup Both of the Loop 4 buttons must be enrolled in the control, even if they will not be used. If one or both of the loops is not being used, program it as Zone Type 23 (No Alarm Response). Otherwise assign it to the desired zone type. 2. Exit Programming Mode after programming is complete. For complete details on how to program the transmitter's serial number at the control panel, see the control unit's installation instructions. Assigning a 5878 to a User On most control panels, if the wall transmitter is assigned to arm and disarm the system, you must assign it to a user in order for it to operate. This is accomplished through User Code programming at the control panel. See the control panel’s Installation and Setup Guide for specific instructions on programming User Codes. If you are programming arming and disarming functions on both serial numbers, each serial number must be assigned to a separate user. SELECTING STANDARD OR HIGH-SECURITY MODE For use with LYNXR Series controls earlier than Revision 13, the Standard Mode must be selected. To select Standard Mode, simultaneously press and hold the STAY, 1 and 2 buttons for three seconds. To select High-Security Mode, simultaneously press and hold the AWAY, 1 and 2 buttons for three seconds. The LED flashes green when transmitting in Standard Mode and red when transmitting in High-Security Mode. ACTIVATING HIGH-SECURITY MODE To ensure proper functionality, the 5878 must be synced to the security system. 1. After selecting High-Security mode, put the system in Go/No Go Test mode. 2. To enroll the transmitter in the receiver, simultaneously press and hold the AWAY, STAY, 1, and 2 buttons until the panel beeps (see Figure 1). For LYNXR Series controls proceed to step 4. Note: The LYNXR Series panels will confirm the enrollment by sounding two beeps. 3. To sync the device in High Security Mode, press either the AWAY, STAY, 1, or 2 button ONCE, until the panel beeps indicating receipt. 4. To enroll the second serial number of the wireless key in the receiver, simultaneously press and hold the 1, 2, 3, and 4 buttons until the panel beeps. 5. To sync the device in High Security Mode, press the 3 or 4 button ONCE, and hold until the panel beeps indicating receipt. For LYNXR Series controls proceed to step 6. Note: If no beep is heard, exit Go/No Go mode, and repeat Steps 1 - 5. 6. Exit Go/No Go mode by entering user code + 1 (OFF). USING TWO RECEIVERS IN HIGH-SECURITY MODE If the control supports two receivers and you plan to use them in the high-security mode perform the following: 1. Enroll the transmitters into the receivers one at a time, by disconnecting Receiver #2, and enrolling as described in “Activating High Security Mode” (above). FOR AGENCY STATEMENTS PLEASE GO TO BOTTOM OF PAGE 3

Navigation menu