Ademco 8DL5883 Remote Security Transceiver User Manual II with FCC label

Download:
Mirror Download [FCC.gov]
Document ID	126027
Application ID	WT3eK4DUILOTMYGdHfYmUQ==
Document Description	II with FCC label
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.71kB (233930 bits)
Date Submitted	2000-11-20 00:00:00
Date Available	2001-01-25 00:00:00
Creation Date	2000-11-16 15:43:27
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2000-11-16 15:43:33
Document Title	II with FCC label

“ADEMCQ
Draft 7/5/00
K3791 7/5/00
5883
Transceiver Module
INSTALLATION AND SETUP GUIDE
INTRODUCTION
The 5383 RF Transceiver Module contains an RF receiver and a
transmitter. It is intended ior use with ADEMCCYs 5300 series RF
transmitters, including bidirectional units (e.g. 5827BD. 580450)v
end the SBOORL Wireless Relay Module (see Fig. 1).
The 5883 receives alarm, status. and control messages from 5800
transmitters, and passes these messages to the control panel via
wired connecflons. The control then responds accordingly
(arm/disarm the system, initiate an alarm. etc.). The 5833 also
transmits system status and other conditions to 580450 or 5827BD
2-way wireless units (it used), which then display these conditions.
When used with the SBOORL Wireless Relay Modulev the 5883 can
operate in two ways, depending on the saooFlL's mode setting. The
5883 can emulate the iunctions oi a 5!!th module or it can control
the SWORL'S relays in the same way a 4204 controls wired relays.
The seas ieatures a Spatial Diversity system that virtually eliminates
the possibility oi 'NuIIs‘ and “Dead Spots" within the coverage area. It
also incorporates ADEMCO’s new Signalsentrym technology (UL-
364 and RF Jam Detect).
commit
mm
Flgtire I. Block Diagram
untri- mum:
e/Q
,,,._"'_,,, m. mun-i...
MOUNTING
With some controls the 5883 PC board may be mounted inside the
control's cablnet Instead oi remotely in its own housing. In either
case, avoid mounting the 5883 with its antennas touching a metal
suriaoe. Follow the applicable mounting directions below.
Removing the Cover
Remove the 5883‘s cover by inserting and twlsdng a screwdriver
blade in the slot at the center of the covers lower edge.
Mounting Inside the control‘s cabinet (refer to Fig. 2):
1. Remove the 5863‘s circuit board irom Its base by bending back the
two ilexible plastic tabs that hold the board‘s lower edge. Discard
the 5383's unused plaso't: cover and base.
2. In the oontroi's cabinet. uniasten and move the control circuit board
downward (it already installed).
a. Hang two short (black) mounting clips (provided) on the raised
cabinet tabs in the cabinet, as shown in Detail B oi Figure 2.
4. insert the top or the 5883's board into the supporting slots at the
top or the cablnet (Detail A). Swing the bottom of the board into the
two short (black) mounting clips installed In step a, and secure it to
the cabinet with the accompanylng screws. See Detail B.
5. Insert the top of the controls board into the slot in the black clips
holding the lower edge oi the 5333 board (see Detail e); position
two long (red) clips at the lower edge oi the board (see Detall C).
6. Swing the lower edge oi the control board into place, and secure
with two additional screws.
7. Insert the grounding lugs (provlded) through the top oi the cabinet
and into the left-hand tenninels oi me antenna blocks (at the upper
edge oi the 5883's circuit board). Secure it to the cabinet with the
two screws provided. See Detail 0.
8. Insert the 5883's two antennas through the two openings in the
top oi the cabinet. one into each block's right-hand terminal. and
tighten the screws to secure them.
9. Aflix the 5838's Summary oi Connections label to the inside oi the
controls cabinet door.
Mounting the see; remotely
NOTE: If you are mounting the 5883 in its own enclosure, the supplied
PCB mounting clips, grounding lugs, and screws are not needed.
1. For concealed wiring. route wires through the rectangular opening at
the rear oi the base before mounu’ng. For suriace wiring entry, a thin
breakaway area is provided along the bases right edge.
2. Mount the module In the selected location. For greatest security, use
all tour mounting holes (two keyslot holes and two round holes) in the
plastic base.
3. Install the antennas in the right-hand terminals oi the two terminal
blocks at the upper edge of the 5388’s circuit board, one into each
block's right-hand terminal, and tighten the screws to secure them.
4. Atfix the 5833's Summary oi Connections label to the inside oi the
housing cover.
Mounting In a Separate cabinet ior Commercial Fire Applications
For Commercial Fire applications, the 5883 module must be mounted
in a separate cabinet (N4865V4—BE), using the ADEMCO Cam Lock
(N6277), and Retainer Clip (N6277—I). Reier to the controls
instructions ior installing me Cam Luck and Retainer Clip.
The cabinet containing the module must be locatad no more than 20
feet from the alarm control cabinet, with no intervening walls or Daniels,
I. Remove the PC board by removing the two screws and bending
back me two flexible plastic tabs that hold the board's lower edge.
2, Insert the top oi the board into the supporting slots at the top oi the
cabinet (see Figure 1 and Detail A, Figure 2).
Secure the bottom of the board with the 2 screws removed in Step 1
above, using an Insulating washer (supplied) between the head of
eaoh mounting screw and the PC board.
IMPORTANT: Ii you are mounting the 5333 in a separate cabinet in a
Commercial Fire installation. do nol use the antenna ground/rig lugs.
3. Aiitx the 5883's Summary oi Connections label to the inside ol the
cabinet door.
hoist FoRANrENrM
. unculr
no Good No toes D
, / at»...
who
SMNG mmcmflrmm
store min—m
omiit A
six Vivi
m or amm—
Wlm/ sI/onfi'rlrlfi smrs
ct-s
riFtOt
chum
mm a
sine vtswoc
seem
landmine cues
mm c
“35va
of tone
not-«mule
perm .,
mrENm no GMNDMG we item-an
Figure 2. insulting the seas Board in the Control's cabinet
(Check the controls installation instructions ior applicability)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2000:11:16 15:43:27
Producer                        : Acrobat Distiller 4.05 for Windows
Modify Date                     : 2000:11:16 15:43:33-05:00
Page Count                      : 1

EXIF Metadata provided by EXIF.tools