Ademco 8DL6150RF Security Device Tranceiver User Manual II with FCC statments

Download:
Mirror Download [FCC.gov]
Document ID	108123
Application ID	XOvLXYBkCUAKfgU4rtwIuA==
Document Description	II with FCC statments
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.15kB (239318 bits)
Date Submitted	2000-07-06 00:00:00
Date Available	2000-09-01 00:00:00
Creation Date	2000-06-30 10:02:47
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2000-06-30 10:03:04
Document Title	II with FCC statments

S150RF Applicatlon Guide
Below is a guide that outlines the possible applications for the 6150111". Use this guide to see how to program
the wireless keys, RF receiver and the House ID in the 6150RF for your particular installation,
Control Panel Are you using
RF receivers RF keypads and/or Program
beymd Bi—difec‘i‘mfl Wireless Keys
system‘s devices on more
capacity? than 1 partition?
4110D mom
4140XMP VISI‘ HWSE
VlSTA-lOSE, VISTA-15, Use Programming Without Local Wireless Keys
VIA-30PSE Local Enable [1] System [1]
Local Disable [0] local [0]
VISTA-20853 Use ngramming Without Local Wireless Keys
[Mal Enable [1] System [ll
Local Disable [0] Local [0]
System Disable [0] Local [0]
Local Disable [0] Local [0]
VISTA-40, VISTA-50? Use Programming Without local Wireless Keys
Local Enable [1] System [1]
Local Disable [0] Local [0]
System Disable [0] Local [0]
local Disable [0] Local [0]
* Two GISORFs are needed for thin application; one connected to partition 1’s keypad terminals, and one connected to partition 25.
u If uaing an RF keypad on only one partition. the 615mm partition assignment must match the partition set in field ms.
m Uset for Local on a partition control, the 615mm partition assignment must match the one programmed in the so device.
Installing the G150RF
Locate the 6150RF in an area and at a height where it is convenient for user operation. The SISORF must be at
least 10' fi-orn the control panel to ensure proper operation of the RF rweiver.
O \
Figure 1: 6150107 Wiring Connections
To install the 6150RF, refer to Figure 1 for wiring connections and perform the following steps:
Step Action
1 Remove the case back by pushing down the two snaps along the GISORF's bottom edge and pulling
the case apart
2 Route the wiring from the control panel through the opening in the case back (See the control
panel’s instructions for proper wire run lengthsli
Mount the case back directly to a wall or electrical gang box,
Connect the power and data wires from the control panel to the terminals on the 6150RF.
Connect the wires for the relay output (if being used) to the terminals on the SISORF’s PC board.
Reattach the keypad to its case back.
Remove the clear protective films from the LCD display and install the keypad labels, as required
NOTE: Upon power up or exiting of the Program Mode, the GlSORF will alternately flash "Ad" and the 2-digit
keypad address and the 2-digit mceiver address on the display Press any key to display the system status.
aeolian:
—=$_._=_—_=___==._——_—=———

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2000:06:30 10:02:47
Producer                        : Acrobat Distiller 4.05 for Windows
Modify Date                     : 2000:06:30 10:03:04-04:00
Page Count                      : 1

EXIF Metadata provided by EXIF.tools