Ademco 8DL6160VPADT2 Touchpad with Prox Reader User Manual K14804V1 B 6160VPADT ii
Honeywell International Inc. Touchpad with Prox Reader K14804V1 B 6160VPADT ii
UserManual.wiki
>
Ademco
>
8DL6160VPADT2 User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![- 2 - STEP-BY-STEP INSTALLATION INSTRUCTIONS Touchpads can be surface mounted using drywall anchors or to a single- or double-gang electrical box. 1. Remove the case back by pushing in the two "snaps" along the Touchpad’s bottom edge and pulling the case apart. See diagram above. 2. Route wiring from the control panel through the case back openings or the knockouts located on the sides. 3. Mount the case back to a wall or electrical box. Do not connect the ECP Data In or Data Out until directed to do so. If the Touchpad’s Prox Reader detects the presence of ECP Data In and Out connections during address programming mode, it will exit to “normal” mode. 4. Wire directly from the Touchpad’s terminal block to the terminal block on the control panel. (Refer to the Wiring Table.) Connect only the red and black Aux. Power connections at the Touchpad. Use only 16-24 AWG wire. Wiring Table Touchpad Control Panel Wire Color G Data In Green – – Aux Pwr (GND) Black + + Aux. Pwr (POS) Red Y Data Out Yellow 5. Re-attach the Touchpad to the case back. 6. Remove clear protective film from LCD display. SETTING THE TOUCHPAD OPTIONS The procedures that follow are used to set the Touchpad address, voice chime mode, and additional console modes. Setting the Touchpad Address When used with the Safewatch Pro/Security Manager 3000 control panels, address 16 must be assigned to the first Touchpad. Additional Touchpads must be set at 17 - 23 and must be enabled additionally in control programming (fields *190 - *196). The Touchpad addresses being used for the Touchpad and the Prox Reader must be enrolled in the control panel. Swiping a Prox Tag when the system is in programming mode may cause programming fields to receive invalid entries. The Touchpad may be set for address 00-30 or for non-addressable mode (31). The default Touchpad address is 31. For valid address settings for your Touchpad, refer to the control panel's Installation & Setup Guide. Notes: • If installed with an older non-addressable panel (using address 31), the prox feature cannot be used. • If unable to enter the address mode, power down, power up, and try again. • If 10 seconds pass with no key entry, the Touchpad automatically exits the address mode. You must power down, power up, and start the address mode again. • The Touchpad will not enter the address mode if the control panel is in programming mode. 1. Apply power to the Touchpad. 2. Within 60 seconds of applying power to the Touchpad, press and hold down the [1] and [3] keys at the same time for 3 seconds. The current Touchpad address will be displayed. 3. Press "00". The current address is cleared. 4. Enter desired two-digit Touchpad address. 5. Press [✱] to accept the displayed address and enter the Voice Chime Mode. "VOICE CHIME" is displayed along with the selected mode "1" or "0". Setting the Voice Chime Mode Setting Voice Chime mode off does not effect the voice status or alarm annunciation. 1. Press [1] to set the Voice Chime mode on or press [0] to set the Voice Chime mode off. 2. Press [✱] to save the displayed Voice Chime mode and enter the Additional Console Voice Touchpad mode. "ADDITIONAL CON" is displayed along with the selected mode "1" or "0". Setting the Additional Console Mode The Additional Console mode must be set for all Touchpads being used. 1. Set the Touchpad Additional Console mode as follows: a. On the Primary Touchpad, press [0] to set the Additional Console mode to NO. b. On any secondary Touchpads, press [1] to set Additional Console mode to YES. 2. Press [✱] to save the mode and enter Prox Reader Address Mode. Setting the Prox Reader Address 1. After exiting “additional console” mode, the Prox Reader will begin communicating with the Touchpad, and the Touchpad will display “Prox Addr? XX” on the first line. 1. XX = the current ECP Address. The Prox Reader address cannot be the same as the Touchpad address. Select an address between 01 and 30 (default = address 23.) 2. Make sure you enable the prox reader address as a keypad in the control panel. 2. Set the current address to "00": Press [0] to clear the current "tens" digit. The cursor moves to the "ones" digit position. Press [0] to clear the current "ones" digit. The cursor moves back to the "tens" digit position. 3. Enter the appropriate address: Enter the proper "tens" digit of the address. The cursor moves to the "ones" digit position. Enter the proper "ones" digit of the address. 4. Press the [*] key to save the entry. The Touchpad will beep three times confirming the address is accepted, and the first digit of the address will flash. You can re-enter the address if desired. 5. Power down the Touchpad. 6. Remove the case back. 7 Connect the green and yellow data in and data out wires at the control panel. Once connected, any Touchpad not enabled in the control at that point will be blank. 8. Re-attach the Touchpad to the case back. 9. Install the Prox Reader location labels on the Touchpad. (Refer to Figure 1.)](https://usermanual.wiki/Ademco/8DL6160VPADT2/User-Guide-1769798-Page-2.png)
![- 3 - ENROLLING PROX TAGS Swiping a Prox Tag when the system is in programming mode may cause programming fields to receive invalid entries. Each Prox Tag is enrolled as a “User” in the alarm system. When enrolling the Tags, the last four digits of the Tag’s serial number is used as the User Code. Refer to the control’s User Guide for instructions on programming user codes. When programming is complete, test the system to ensure that each Prox Tag arms and disarms the system as specified. VIEWING THE TOUCHPAD ADDRESS During normal operation, press and hold down the [1] key and [3] key at the same time for about 3 seconds. The current address is displayed. No key entry is allowed. Press any key to exit or wait 10 seconds to exit the viewing mode. TOUCHPAD DISPLAYS AND LEDS The Touchpad provides a two-line alphanumeric display and custom zone descriptors. The following table identifies the Touchpad’s LEDs and associated functions: LED Function ARMED Lights red when the system is armed in any mode. READY Lights green when the system is "ready" to be armed. MESSAGE Flashes red when message waiting or lights (steady) when in record mode. PROGRAMMABLE FUNCTION KEYS The Touchpad's programmable function keys [A, B, C] are normally used for panic functions, but they can be programmed for other special functions instead. If they are programmed for other special functions, the associated Touchpad key pairs still provide the respective panic alarm (if programmed). Refer to the control panel’s Installation & Setup Guide for details. Function Keys Equivalent Key Pairs A [1] and [*] B [*] and [#] C [3] and [#] D NONE • Function keys must be held down for at least 2 seconds to activate the programmed function. • If functions other than panics are assigned to the programmable function keys, programmed panics must be initiated by pressing the programmed key pair. FUNCTION KEY LABELS A set of adhesive-backed labels with some typical function symbols (i.e., fire, police, personal emergency, etc.) is provided. These labels can be placed on or next to the keys to identify each key's function for the end user (as determined by the capability and programming of the control panel; refer to the installation and setup guide for the control panel). 6160vADT-50-001-V1MOUNTING RELEASE SNAPS(Remove case back by pushing up the 2 "snaps" alongthe keypad's bottom edge and pulling the case apart.)SIDE VIEW1234567890#STAYBYPASSCHIMEINSTANTAWAYCODETESTOFFREADYARMEDREADYMICMESSAGERECORD VOLUME PLAYSTATUS FUNCTIONVOICEABCD OPERATING THE KEYPAD For operating instructions, see the User Guide provided with this keypad. For additional information, refer to the User Guide for the control panel used with this keypad. Zone Descriptors Only the zone descriptors listed in Table 1 are supported by this Touchpad. If using zone descriptors not supported by this Touchpad, you must turn voice status and voice chime off. Table 1 provides is a list of applicable zone descriptors and index entries. Refer to the control panel’s Installation and Setup Guide for information about how to program zone descriptors. TABLE 1. ZONE DESCRIPTORS AND INDEX ENTRIES ALARM 002 DOOR 057 KITCHEN 105 PATIO 146 UPSTAIRS 207 ATTIC 009 EMERGENCY 067 LAUNDRY 106 POLICE 151 UTILITY 208 BABY 012 EXIT 071 LIBRARY 109 POOL 152 WINDOW 217 BACK 013 FIRE 079 LIVING 113 ROOM 162 YARD 223 BASEMENT 016 FLOOR 080 MAIN 122 SHED 168 ZONE 225 BATHROOM 017 FRONT 085 MASTER 123 SHOP 170 1ST 228 BEDROOM 019 GARAGE 089 MEDICAL 125 SIDE 173 2ND 230 CLOSED 040 GUN 094 MOTION 131 SLIDING 175 3RD 232 DEN 050 HALL 095 OFFICE 136 SMOKE 176 DETECTOR 052 HOUSE 099 OPEN 138 STORAGE 185 DINING 053 INSIDE 101 PANIC 144 SUPERVISED 190](https://usermanual.wiki/Ademco/8DL6160VPADT2/User-Guide-1769798-Page-3.png)
