Ademco 8DL6CO Carbon Monoxide Detector User Manual 20180228 v1 SiXCO EXHIBIT 9 1 Install Guide

Download:
Mirror Download [FCC.gov]
Document ID	3768996
Application ID	MzWRklRWd7JSzxPQemwaqQ==
Document Description	User Manual_20180228_v1 - SiXCO EXHIBIT 9-1 Install Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	92.04kB (1150478 bits)
Date Submitted	2018-03-05 00:00:00
Date Available	2018-09-01 00:00:00
Creation Date	2018-02-01 10:19:04
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-02-01 10:19:08
Document Title	User Manual_20180228_v1 - SiXCO EXHIBIT 9-1 Install Guide
Document Creator	Acrobat PDFMaker 18 for Word
Document Author:	E727032

SiXCO Carbon Monoxide (CO) Detector / Monoxyde de carbone (CO)
Quick Installation Guide
Guide d'installation rapide
This device is intended for use with Honeywell controls that support SiX series devices
including the SiXCO. Check the control for compatibility with this device. This device
occupies one control panel zone.
This device is intended for use with Honeywell controls that support SiX series devices
including the SiXCO. Check the control for compatibility with this device. This device
occupies one control panel zone.
See Honeywell Installation Guide (P/N 800-23974–
https://mywebtech.honeywell.com/) and the Limitations of
Carbon Monoxide Alarm Systems Insert (P/N 800-15144
12/15) and Limitation of Carbon Monoxide Detectors (P/N
K14670V1 4/08 Rev. A).
FEATURES
•
•
•
•
•
10-year life Carbon Monoxide (CO) sensor
CO Detector End-of-Life reporting (detector needs replacing)
CO Maintenance Reporting
Low Battery Detection
One Go / All Go: all CO detectors in the system programmed
as one-go-all-go will sound on alarm.
Voir les instructions d'installation complètes (800-23974 https://mywebtech.honeywell.com/) et les limites de cet
insert de système d'alarme au monoxyde de carbone (80015144FC 12/15)
CARACTÉRISTIQUES
Signalement de la fin de vie du détecteur de CO (détecteur
devant être remplacé)
• 10-year life Carbon Monoxide (CO) sensor
• CO Maintenance Reporting
• Détection de pile faible
• Une seule fois pour tout : Tous les détecteurs de fumée du
système programmés comme « Une seule fois pour tout »
retentiront.
POWER UP
POWER UP
•
•
•
Remove battery pull tab. Be sure batteries are seated
properly to avoid a low battery condition after 15 seconds.
Upon power up, Green LED Blinks every 2 secs / Sounder is
Silent.
•
Remove battery pull tabs. Be sure batteries are seated
properly to avoid a low battery condition after 15 seconds.
Upon power up, Green LED Blinks every 2 secs / Sounder is
Silent.
ENROLLMENT
ENRÔLEMENT
IMPORTANT NOTES:
IMPORTANT NOTES:
• The Carbon Monoxide (CO) has a
unique MAC ID number (serial
number) and is used for
enrollment.
• Once enrolled, the device cannot
be used with another system
until it is removed from the
current controller. See the 24hour Enrollment Deletion section
below or the controller’s
instructions.
• The Carbon Monoxide (CO) has a
unique MAC ID number (serial
number) and is used for
enrollment.
• Once enrolled, the device cannot
be used with another system until
it is removed from the current
controller. See the 24-hour
Enrollment Deletion section below
or the controller’s instructions.
Enroll the Device Services (CO)
Enroll the Device Services (CO)
1. Remove the detector from the
base plate (tamper switch must
be faulted when enrolling).
1. Remove the detector from the
base plate (tamper switch must
be faulted when enrolling).
2. Put the control panel in Zone
Programming mode.
2. Put the control panel in Zone
Programming mode.
For Lyric Controller: Security >
installer code > Program >
(scroll down) > SiX
Programming
For Lyric Controller: Security >
installer code > Program >
(scroll down) > SiX
Programming
3. Pull the battery tab to activate
enrollment process (be sure
batteries are seated properly to
avoid a false low battery
condition). If the battery tab has
already been removed and the
unit is powered up, press Test
switch for less than 3 seconds to
activate the enrollment process.
3. Pull the battery tab to activate
enrollment process (be sure
batteries are seated properly to
avoid a false low battery
condition). If the battery tab has
already been removed and the
unit is powered up, press the
Test switch for less than 3
seconds to activate the
enrollment process.
4. The device attempts enrollment (green LED flashes about 8 seconds). If successful, the
green LED lights steady for 3 seconds and the detector chirps indicating a successful
enrollment.
4. The device attempts enrollment (green LED flashes about 8 seconds). If successful, the
green LED lights steady for 3 seconds and the detector chirps indicating a successful
enrollment.
If the LED does not light steady, enrollment failed. Retry by pressing Test switch for less
than 3 seconds.Supervision: Detector supervision is factory set for 1 minute and is not
programmable.
If the LED does not light steady, enrollment failed. Retry by pressing Test switch for less
than 3 seconds.Supervision: Detector supervision is factory set for 1 minute and is not
programmable.
5. To assign zone descriptors for each of the zones and/or change device type or zone
response type, select the zone then select Edit and make the desired changes. Press
Save when done.
5. To assign zone descriptors for each of the zones and/or change device type or zone
response type, select the zone then select Edit and make the desired changes. Press
Save when done.
24-Hour Enrollment Deletion
24-Hour Enrollment Deletion
Use this procedure within 24 hours of initial enrollment to delete this device from the
controller. This allows reenrollment in a specific controller in case enrollment in that
controller failed (i.e., the device inadvertently enrolled in a different controller). This resets
the device to factory default settings and removes the communication link data in the
controller in which it is enrolled, allowing the device to be reenrolled in the desired
controller.
Use this procedure within 24 hours of initial enrollment to delete this device from the
controller. This allows reenrollment in a specific controller in case enrollment in that
controller failed (i.e., the device inadvertently enrolled in a different controller). This resets
the device to factory default settings and removes the communication link data in the
controller in which it is enrolled, allowing the device to be reenrolled in the desired
controller.
NOTE: Pressing and holding the test button (while powering the detector) will arm the
detector to perform a reset to factory defaults.
NOTE: Pressing and holding test button (while powering the detector) will arm the
detector to perform a reset to factory defaults.
TO SILENCE THE DETECTOR
Press the test switch. The detector sounds again after 5 minutes if the alarm condition
continues.
POUR FAIRE TAIRE LE DÉTECTEUR
Appuyez sur le bouton de test. Le détecteur sonne de nouveau après 5 minutes si la
condition d'alarme est toujours présente.
NOTE: The detector can only be silenced once per event.
NOTE: The detector can only be silenced once per event.
MOUNTING
CEILING / PLAFOND
If the device is not in its final mounting
location when enrolled, conduct Go/No
Go tests (see controller’s instructions)
to verify adequate signal strength.
Adjust the device location and
orientation as necessary.
WALL / MUR
MONTAGE
Si l’appareil n’est pas dans son
emplacement de montage final lorsqu’il
est enrôlé, effectuez des tests Tout ou
rien (voir les instructions du panneau de
commande) pour vérifier que la
puissance dusignal est adéquate. Au
besoin, modifiez l'emplacement ou
l'orientation du dispositif.
FUNCTIONAL TEST
Product must be
tested at least once
each year
REPLACE BATTERIES /
REMPLACEMENT DES PILES
TEST FONCTIONNEL
Le fonctionnement du
produit doit être vérifié
au moins une fois par
année
PERIODIC CLEANING
NETTOYAGE PÉRIODIQUE
NOTE
Notify the proper
authorities that the
CO detector is
undergoing
maintenance and the
system will
temporarily be out of
service.
NOTE :
Avisez les personnes compétentes
qu'un détecteur de CO est hors service
pour cause d'entretien et que, par
conséquent, le système sera
temporairement hors service.
LED Indication & Sounder during Test and Trouble /
Confirmation par DEL et sonore durant le test et la maintenance
Status LED (Top) / Estado
Sounder / Sonador
del LED
Blink Red once every sec /
Temp-4
Clignotement rouge une fois
Tempo. -4
par seconde
MODE/ MODO
CO Test 1ab / Test CO
RealTest™ Functional CO Test
– Waiting for gas entry / Test
fonctionnel de CO RealTest™ 2ab
– En attente d'une entrée de gaz
Blink Green once a sec /
clignotement en vert par
seconde
RealTest™ Functional CO Test Successful gas entry /
Test fonctionnel de CO
RealTest™ 2ab – Entrée de gaz
effectuée avec succès
Blink Red every 10 secs /
clignotement en rouge à
toutes les 10 secs
Temp-4
Tempo. -4
Low Battery / Pile faible
Blink Amber once every
45 sec /
Clignotement ambre à toutes
les 45 secs
Chirp every 45 seconds
after
7 days / Émet des
épiements toutes les
45 secs après 7 jours
1ab
CO Trouble/
Défectuosité du dét. de CO
CO End of Life2- First 29 days /
Fin de vie du dét. de CO4Premier 29 jours
CO End of Life2- After 30 days /
Fin de vie du dét. de CO4- après
30 jours
Silent /
Silencieux
SPECIFICATIONS / SPÉCIFICATIONS:
Battery / Pile:
2 x 3V, CR123A Lithium; Panasonic CR123A or DURACELL DL123, DL123A
Sensitivity / Sensibilité :
Meets UL2034/UL2075 CO sensitivity requirements
Audible Signal: 85dBA / Signal audible: 85 dBA
Dimensions: Thick 1.65 in (4.19 cm); Diameter 5.30in (13.462cm)
Weight: 7.7 oz; 218.3 g / Poids : 7,7 oz; 218.3 g
Tamper / Interrupteurs antisabotage: Wall Tamper/Wall Tamper
Operating Temperature / Température de fonctionnement : 32°– 122° F / (0°– 50° C)
Double Blink Amber every 5
secs / Clignotement ambre à
toutes les 3 secs
Double Blink Amber every 3
secs / Clignotement ambre à
toutes les 3 secs
Double Blink Amber every 3
secs / Clignotement ambre à
toutes les 3 secs
Storage Temperature / Plage de température de stockage : 14-158°F
(-10°-70°C)
Relative Humidity / Humidité de fonctionnement :
20-95% RH (Agency Compliance – 93% max.), non-condensing
NOTE: Batteries available at your local retailer or distribution center.
NOTE : Batteries disponibles chez votre revendeur ou votre centre de distribution
local.
Silent /
Silencieux
Caution!
The batteries used in this device may present a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 212°F (100°C) or dispose of in fire. Use two
Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries
may present a risk of fire or explosion. Keep used batteries away from children. Dispose of
used batteries properly.
Chirp every 45 secs/
Émet des épiements
toutes les 45 secs
Remove old batteries. Wait 10 seconds and then replace with two new batteries. To avoid a
low battery indication when installing new batteries, both batteries must be installed within
15 seconds of installing the first one. Any low battery condition that may have occurred
should clear when the back plate is installed.
Silent /
Silencieux
1a Test activated by pressing and releasing the test switch; Detector is functioning
properly (within proper sensitivity). See Functional Test section for Functional Test
activation and procedure. / Test activé par le bouton de test; Le détecteur
fonctionne adéquatement (avec la sensibilité appropriée).
1b If Test mode is activated and the LED and Sounder do not function, check for
maintenance or trouble conditions. / Si le mode de test est activé et que la DEL et
l'avertisseur sonore ne fonctionnement pas, vérifiez s'il y a des conditions de
maintenance ou de défectuosité.
Starts chirping after 30 days, continues until the batteries are replaced or die / Le
détecteur commence à émettre des pépiements 30 jours après sur une base
continue jusqu'à ce que la pile soit remplacée ou morte.
NOTE: For programming, see the Controller’s instructions.
NOTE: Pour la programmation des alarmes de fumée ou de CO et Tamper, consultez les
instructions du contrôleur.
Approval Listings / Approbations Homologations:
FCC/IC
Listed to UL 2075, and CSA 6.19 MAR2001 (R2016) / Conforme aux normes UL 2075, ou
CSA 6.19 MAR2001 (R2016).
Other Standards / Autres normes: RoHS
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions or User's Manual. Unauthorized changes or modifications could void the
user's authority to operate the equipment.
Mise en garde!
Les piles utilisées dans ce dispositif peuvent présenter des risques d'incendie ou de brûlure
chimique si elles sont mal traitées. Ne rechargez pas, ne désassemblez pas, ne faites pas
chauffer et ne jetez pas au feu les piles à plus de 100 °C (212 °F). Utilisez des dos piles au
lithium Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres types de
piles peut présenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la
portée des enfants. Débarrassez-vous des batteries utilisées de façon appropriée.
Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par dos nouvelles piles.
Pour éviter une indication de piles faibles lorsque vous installez de nouvelles piles, les dos
(2) piles doivent être installées en deçà de 15 secondes après l'installation de la première.
Toute condition de pilles faibles qui aurait pu se produire devrait être rétablie une fois la
plaque arrière installée.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS
DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
POUR LES LIMITES DU SYSTÈME D’ALARME AU COMPLET, REPORTEZ-VOUS AU
GUIDE D’INSTALLATION DU PANNEAU DE COMMANDE.
Support / Pour de l’assistance en ligne, visitez : https://mywebtech.honeywell.com/
U.S. warranty / U.S. garantie: www.honeywell.com/security/hsc/resources/wa
For patent info, see: / Pour des informations sur les brevets, voir :
www.honeywell.com/patents
FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canada’s
license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie
Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas
causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris
les interférences causant une réception indésirable.
MyWebTech
Warranty / Garantie
Patents / brevets
Agile Reference #800-23974 1/18 Rev A
I56-0620-000
 2018 Honeywell International Inc. Honeywell and is a registered
trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All
rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : E727032
BJ Classification               : Honeywell Unrestricted
Company                         : Honeywell
Create Date                     : 2018:02:01 10:19:04-05:00
Modify Date                     : 2018:02:01 10:19:08-05:00
Source Modified                 : D:20180201151723
Subject                         : 
Bj Document Label Field Code    : Honeywell Unrestricted
Bj Document Label Field Code Header Footer: Honeywell Unrestricted
Bj Document Label XML           : 
Bj Document Security Label      : Honeywell Unrestricted
Bj Saver                        : RTHabjDncQUIrFiViV8PDdlm+eM6fL4p
Doc Index Ref                   : 04cf878b-2dcc-4f9b-883e-9a68c5b3ac20
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2018:02:01 10:19:08-05:00
Creator Tool                    : Acrobat PDFMaker 18 for Word
Document ID                     : uuid:752026f4-1702-4df8-8390-803ba5f68dd0
Instance ID                     : uuid:2a145359-fa38-4dea-b8c5-20683486f036
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : E727032
Producer                        : Adobe PDF Library 15.0
Keywords                        : 
Page Layout                     : OneColumn
Page Count                      : 2

EXIF Metadata provided by EXIF.tools