Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2771928 |
| Application ID | gDIkyQ5Djc+y5UFRxkBm3Q== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 12.26kB (153208 bits) |
| Date Submitted | 2015-10-02 00:00:00 |
| Date Available | 2015-10-02 00:00:00 |
| Creation Date | 2015-03-23 09:31:57 |
| Producing Software | Adobe PDF Library 9.0 |
| Document Lastmod | 2015-03-23 09:31:59 |
| Document Title | new A4 template |
| Document Creator | Acrobat PDFMaker 9.1 for Word |
| Document Author: | sam goldberg |
AY-x20 Family Multi-format Proximity Readers Installation Manual 1. Introduction The AY-x20 is a family of RFID proximity card readers to be installed for use with access control systems. The AY-x20 family reads the proximity card and transmits its data to the access control system, using common multi-format Wiegand outputs. 1.1 Figure 1: AY-x20 Family Key Features Selectable Wiegand 26-Bit, Clock & Data Reads 26-Bit EM or Rosslare format cards Waterproof Green LED control line Red LED control line Buzzer control line Hold control line Optical tamper sensor AY-M20 Tamper output line UV-protected polycarbonate housing AY-H20 AY-L20 AY-J20 AY-K20 AY-Q20 2. Technical Specifications 2.1 Electrical Characteristics Specification Power Supply Type 2.2 AY-M20 AY-J20 AY-H20 AY-L20 AY-K20 AY-Q20 5–16 VDC Absolute Maximum (nonoperating) 18 VDC Current @ 12V Standby: 85 mA Maximum: 100 mA Read Range** 10 cm (3.9 in.) LED Control Input Dry Contact, N.O. Operating Humidity Range 2.3 8 cm (3.2 in.) Open collector, active low, max. sink current 16 mA Maximum Cable Distance to Controller 150 m (500 ft) RF Modulation ASK, 125 KHz 4 cm (1.6 in.) 106 KHz * All input voltages should be limited to 1 A maximum. For VAC, the voltage range is peak-to-peak. ** Measured using a Rosslare proximity card or equivalent. Range also depends on electrical environment and proximity to metal. AY-M20 AY-J20 AY-H20 AY-L20 AY-K20 AY-Q20 -31°C to 63°C (-25°F to 145°F) 0 to 95% (non-condensing) Physical Characteristics 8B Model Tamper Output Bit Rate Specification Operating Temp. Range Linear type (recommended) Operating Voltage Range* Environmental Characteristics 7B Dimensions (H x W x D) Weight AY-M20 88.9 x 88.9 x 15 mm (3.5 x 3.5 x 0.6 in.) 109 g (3.9 oz.) AY-J20 120.0 x 42.0 x 14 mm (4.7 x 1.7 x 0.6 in.) 88.5 g (3.1 oz.) AY-H20 109.9 x 74.9 x 15 mm (4.3 x 3.0 x 0.6 in.) 100 g (3.5 oz) AY-L20 144.9 x 42.9 x 20 mm (5.7 x 1.7 x 0.8 in.) 116 g (4.1 oz) AY-K20 79.9 x 39.9 x 12.8 mm (3.2 x 1.6 x 0.5 in.) 70.5 g (2.5 oz) AY-Q20 120 x 76 x 20 mm (4.7 x 3.0 x 0.8 in.) 480 g (17.0 oz) 3. Installation 3.1 6. Remove the reader's snap-off front cover to reveal the two screw holes (see Figure 2 ). Installation Kit The installation kit consists of the following items to be used during the installation procedure: One mounting template Two pan head screws and wall plugs One L-shaped security screw tool One security screw 3.2 Figure 2: Removing the Top Cover Mounting the AY-x20 Reader Before mounting, you should determine the best location for the reader. To mount the reader: 1. Peel off the back of the self-adhesive mounting label template and place it at the required mounting location. 2. Using the template as a guide, drill two holes (sizes indicated on the template) used for mounting the reader onto the surface. 7. Align the two holes of the reader with those drilled in the wall and firmly attach the reader to the wall with two screws, whose size is indicated on the template. 3. Insert a suitable wall plug into each hole. 4. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal, place a grommet or electrical tape around the edge of the hole. 8. Relocate the front cover onto the reader. 5. Wire the reader to the controller as described in Section 4. A linear type power supply is recommended. The reader can also be mounted using strong epoxy glue. After application, the reader should be firmly held in place until the glue dries. Card readers are to be used with control panels whose power supply is UL Listed Class 2 or equivalent. 4. Wiring The AY-x20 is supplied with a 10-conductor 18” pigtail. Table 1: Wiring To connect the reader to the controller: Wire Color 1. Prepare the reader cable by cutting its jacket back about 3 cm (1¼") and strip the insulation from the wires about 1.2 cm (½"). Wiegand 26-Bit Output Clock & Data Output Mode Mode Red +DC +DC 2. Prepare the controller cable by cutting its jacket back 3 cm (1¼") and strip the insulation from the wires about 1.2 cm (½"). Black Ground Ground Green Data 0 Data 3. Splice the reader’s pigtail wires to the corresponding controller wires (as indicated in Table 1) and cover each joint with insulating tape. White Data 1 Clock Orange Green LED Green LED Brown Red LED Red LED 4. If the tamper output is being utilized, connect the purple wire to the correct input on the controller. Yellow Buzzer Buzzer 5. Trim and cover all unused conductors. Blue Hold Hold Purple Tamper Tamper Grey Open Input Connected to GND • The individual wires from the reader are color-coded according the Wiegand standard. • When using a separate power supply for the reader, this supply and that of the controller must have a common ground. • The reader’s cable shield wire should be preferably attached to an earth ground, or a signal ground connection at the panel, or power supply end of the cable. This configuration is best for shielding the reader cable from external interference. 5. Operation Instructions 5.1 Testing 5.3 Once the reader is wired to a power supply and to the controller, you should test the reader. If the LED control wires (orange and brown) are not used (open), the reader LED remains red continuously, and flashes green momentarily when successfully reading a card. To test the reader: The bi-color LED color can be controlled using the orange and brown wires. 1. Power up the reader. The LED and beeper activate one time. This indicates that the reader is working properly. 2. Present the appropriate type of proximity card to the reader. The LED momentarily flashes green and a short beep is emitted indicating that the card was read properly by the reader. For Wiegand 26-bit operation, the grey wire should be held not connected. For Clock & Data operation, the grey wire should be connected to the ground When the orange wire is grounded, the LED is green When the brown wire is grounded, the LED is red When both the brown and orange wires are grounded, the LED is amber. Buzzer Control If the buzzer control wire (yellow) is not used (open), the buzzer beeps only when a card is read successfully. The buzzer can also be controlled using the yellow wire. When the yellow wire is grounded, the buzzer sounds. Output Selection 5.4 After the card data is processed by the controller, the controller can then turn the LED green. Refer to the controller description of the LED operation if the reader LED is controlled by the controller. 5.2 LED Control 5.5 Hold Control The reading of cards can be disabled using the hold wire (blue). If the blue wire is grounded, the reader ignores all cards placed in its field. If the blue wire is open, the reader reads cards normally. 5.6 Tamper Output This reader has an optical tamper sensor. When the sensor detects light, the tamper output is grounded. When the sensor does not detect light, the tamper output is held to the high open collector. Declaration of Conformity This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Limited Warranty The full ROSSLARE Limited Warranty Statement is available in the Quick Links section on the ROSSLARE website at www.rosslaresecurity.com. Rosslare considers any use of this product as agreement to the Warranty Terms even if you do not review them. Contact Information United States and Canada China Rosslare Security Products, Inc. Southlake, TX, USA Toll Free: +1-866-632-1101 Local: +1-817-305-0006 Fax: +1-817-305-0069 support.na@rosslaresecurity.com Rosslare Electronics (Shenzhen) Ltd. Shenzhen, China Tel: +86-755-8610-6842 Fax: +86-755-8610-6101 support.cn@rosslaresecurity.com Europe Rosslare Enterprises Ltd. Kowloon Bay, Hong Kong Tel: +852-2795-5630 Fax: +852-2795-1508 support.apac@rosslaresecurity.com Asia Pacific, Middle East, Africa Rosslare Israel Ltd. Rosh HaAyin, Israel Tel: +972-3-938-6838 Fax: +972-3-938-6830 support.eu@rosslaresecurity.com India Latin America www.rosslaresecurity.com 0706-0960030+04 Rosslare Electronics India Pvt Ltd. Tel/Fax: +91-20-40147830 Mobile: +91-9975768824 sales.in@rosslaresecurity.com Rosslare Latin America Buenos Aires, Argentina Tel: +54-11-4001-3104 support.la@rosslaresecurity.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : sam goldberg Create Date : 2015:03:23 09:31:57+02:00 Modify Date : 2015:03:23 09:31:59+02:00 Product Name : Product Name Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2015:03:23 09:31:59+02:00 Creator Tool : Acrobat PDFMaker 9.1 for Word Document ID : uuid:1b80fa49-d077-4974-8f6e-48f367fb4e04 Instance ID : uuid:2735ce7e-6a4c-4ff2-8be7-07ad12d18c4c Subject : 15 Format : application/pdf Title : new A4 template Creator : sam goldberg Producer : Adobe PDF Library 9.0 Source Modified : D:20150323072643 Company : SYO Product 0020 Name : Product Name Page Layout : OneColumn Page Count : 4EXIF Metadata provided by EXIF.tools