Ademco RV8310 User Manual

Honeywell International Inc manual

a href="https://usermanual.wiki/Ademco" itemprop="url"> Ademco >

manual

HoneywellDRAFTUser’s Manual                                      RT8220A is a transmitter to be used with the RV8310D receiver/valve.RF MILLIVOLT SYSTEMThe RF millivolt system consists of a RV8310D receiver/valve, RT8220A transmitter,and a pilot burner with two Q313 thermopiles.The RV8310D is flame powered with two thermopiles, and has flame poweredmodulation, line powered fan modulation, and a quick dropout function of 30 seconds orless with loss of pilot flame.The receiver has a manual switch. If the switch is in the REMOTE mode and the pilot islit, the RT8220A transmitter can control the main valve, flame modulation, fan control,and set temperature. If the switch is in the LOCAL mode and the pilot is lit, the valve willbe at the highest fixed pressure setting and the RT8220A transmitter cannot turn off themain burner. The RT8220A will control the fan but not the flame modulation.The pilotstat knob in the valve portion of the control provides for the OFF mode for theRV8310D. When the pilotstat knob is rotated to the OFF position, the pilot and mainvalve are turned off and the RT8220A transmitter provides no control.The valve portion of the control has a pilotstat, pilot adjustment, European style inlet andoutlet pressure taps, 7/16-24 UNS pilot connection, and 3/8” NPT inlet and outletconnections. The capacity is 60,000 BTUH at 1” p.d..The regulator is dedicated natural gas or LP. The receiver/valve is rated at 175 F. If theambient temperature rises above 185 F, the output pressure is reduced until the ambienttemperature drops below 175F.INSTALLATION OF RV8310D1. Use only on a vented appliance.2. Turn off the gas supply at the appliance service valve before starting the installation,and perform a Gas Leak Test after the installation is complete.
3. Mount valve 0 to 90 degrees, in any direction – including vertically – from the uprightposition of the gas control knob4. Attach four thermopile leads. Two leads are white wires with a terminal. They areattached to the terminals with a white dot on the cover next to them. The two leadswith the red wires attach to the remaining terminals.OPERATION1. Turn the pilotstat knob counterclockwise from OFF  to the PILOT position, push theknob down, and hold in position. The pilot valve opens and allows gas to flow to thepilot burner.2. Push the plunger on the piezo until the pilot burner is lit. When the pilot burner is lit,the LED on the control will come on  after approximately 40 seconds and  will becontinuously red. When the light turns off which will be approximately 10 secondsafter it has been continuously red, the receiver/valve is fully powered.3. Release the knob. The shaft will move upward. The pilot burner should now stayburning. If the pilot burner goes out, repeat step 2.4. Turn the knob counterclockwise to the ON position. If the manual switch is in theLOCAL position, the main burner will turn on immediately.5. On the initial use of a transmitter, a recognition operation is required between thereceiver/valve and transmitter. Change the switch from LOCAL to REMOTE. Pressthe fan or flame button on the transmitter within 30 seconds. The LED will blinkindicating that the transmitter will now work with the receiver/valve. If the switchcontinues in the REMOTE position, the RT8220A transmitter will now control themain valve, flame modulation level, and fan control.6. If the manual switch is in the LOCAL position, the valve will be at the highest fixedpressure setting. The RT8220A transmitter will control the fan only.SHUT OFF PROCEDURE1. If the manual switch is in the REMOTE position, the RT8220A transmitter can shutoff the main burner and fan. However, the control is still on and a command from thetransmitter can turn on the main burner or fan.2. To shut off the system, turn the pilotstat knob clockwise to the OFF position. Thisaction closes the main gas and safety valves. The transmitter cannot turn on the mainburner or fan.TRANSMITTER – RT8220AThe RT8220A controls the flame level, fan speed, and room temperature. The three basicoperating modes are the OFF mode, ON (manual) mode, and AUTO mode.
Download:
Mirror Download [FCC.gov]
Document ID71612
Application ID2ptyKohbHg5QauRLXGuHIA==
Document Descriptionmanual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize1.03kB (12814 bits)
Date Submitted1999-11-23 00:00:00
Date Available2000-01-31 00:00:00
Creation Date2001-05-16 09:32:28
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-05-16 09:32:29
Document Titlemanual
FCC ID Filing: HS9-RV8310

Navigation menu