Adtran Mx2820 48 Vdc M13 Mux Users Manual
MX2820-48 VDC M13 MUX to the manual 5a224781-4990-28f4-8daf-ff5bf3def199
2015-01-24
: Adtran Adtran-Mx2820-48-Vdc-M13-Mux-Users-Manual-345133 adtran-mx2820-48-vdc-m13-mux-users-manual-345133 adtran pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
MX2820 –48 VDC M13 MUX MX2820 M13 MUX LED STATUS FOR ACTIVE MUX ACT P/N 1186002L5 CLEI: M3C3WG0ATA ALM M13 MUX DS3 STAT 1186002 ACT DS3 TEST ALM STAT DS3 DS1 STAT TEST STAT DS1 #61186002L5-22A# TEST DS1 TEST C A U T I O N ! HANDLING PRECAUTIONS REQUIRED. Green Green/Amber (Alternating) Red Amber Red/Amber (Alternating) Red (Flashing) Green Red Red (Flashing) Green Red Red (Flashing) Red (Flashing once per event) Red/Green (Alternating) Off Amber Amber (Flashing) Off Green Red Red (Flashing) LED STATUS FOR STANDBY MUX ACT ALM DS3 STAT DS3 TEST DS1 STAT DS1 TEST SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY. DESCRIPTION Normal (All OK) Normal and console open Self-test failed Software update in progress Self-test failed and console open Module has failed No critical, major, or minor alarms Major or minor alarm in progress Critical alarm in progress Normal (DS3 OK) AIS, OOF, RAI, Idle alarms DS3 LOS or DS3 Failure (critical) Single/Burst DS3 code violations DS3 XCV threshold exceeded No DS3 tests in progress In test (locally originated) In test (remotely originated) All DS1s are disabled Enabled DS1s normal (All OK) Non-critical DS1 alarm (CAIS, LAIS) LOS on an enabled line (critical DS1 alarm; non-critical system alarm) 4 Red (Flashing once per event) Single/Burst RX DS1 code violation !/! Red/Green (Alternating) DS1 XCV threshold exceeded " Off No DS1 tests in progress ! Amber In test (locally originated) 4 Amber (Flashing) In test (remotely originated) ! !/! ! ! !/! 4 ! ! 4 ! ! 4 4 !/! " ! 4 " ! ! 4 4 ! 4 " " 4 " " 4 " Green (Flashing) Amber Red Off Off Red (Flashing) Off Off Red (Flashing) Off 61186002L5-22A 0408 Normal (All OK) Software update in progress Failure Permanent state during standby Normal (DS3 OK) In test (remotely originated) Permanent state during standby Normal (DS1s OK) DS1 Failure Permanent state during standby The MX2820 M13 MUX is a plug-in unit for the MX2820 chassis that provides an M13 multiplexer function to the MX2820 system. Two MX2820 M13 MUX cards are used together to provide a redundant M13 multiplexer circuit. The MX2820 M13 MUX: ♦ provides 1:1 redundancy ♦ meets the requirements for NEBS Level 3. INSTALLATION AND TURNUP After unpacking the unit, inspect it for damage. If damage is found, file a claim with the carrier and then contact ADTRAN Customer Service. Refer to the Warranty Statement on this Job Aid. This module occupies a MUX slot in the MX2820 chassis. To install the M13 MUX in the chassis, perform the following steps: 1. Pull the ejector tab into the down position and gently but firmly push the MUX into the selected MUX slot. Simultaneous thumb pressure at the top and at the bottom of the unit will ensure a good seat of the MUX into the backplane connector. 2. Push the ejector tab up and closed against the front panel. Upon installation, the MUX will begin a self-test. This is followed with the LEDs reflecting the true state of the hardware. OPERATIONAL SPECIFICATIONS ♦ Operates from A or B –42 VDC to –56 VDC input voltage power feeds. ♦ Operates over extended temperature range of –40ºC to +50ºC without fans or –40ºC to +65ºC with fans. ♦ Storage –40ºC to +85ºC. Relative humidity to 95 percent, noncondensing. COMPLIANCE ♦ The MX2820 M13 MUX complies with UL 60950, NEBS Level 3, and GR-1089-CORE. ♦ The MX2820 M13 MUX is intended for installation in restricted access areas only. ♦ The MX2820 M13 MUX is intended for installation in a Type “B” or “E” enclosure. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment. Code Input Output Power Code C C Telecommunication Code (TC) – – Installation Code (IC) A – PROVISIONING All provisioning of the MX2820 M13 MUX will be handled through the SCU. The menu tree on the reverse of this Job Aid provides the options and default settings for the MX2820 M13 MUX. NOTE: When provisioning the L5 MUX, use the menu tree on this Job Aid, rather than the manual, as there are some code differences in the MX2820 Manual. PRICING AND AVAILABILITY 800.827.0807 TECH SUPPORT 800.726.8663 RETURN FOR REPAIR 256.963.8722 www.adtran.com 61186002L5-22A MX2820 –48 VDC M13 MUX 1. DS3 Framing CLEI Code To/from SCU menus 1. Configuration Part Number Serial Number 1. Network Interface 1. C-BIT 1. Loop 2. M13* 2. Local* 2. DS3 Timing 1. Disabled 1. Disabled* 2. FEAC/C-BIT* 3. FEAC 3. DS3 Remote Loopbacks 2. 1E-3 3. 1E-4 4. C-BIT Code Version Code Checksum Boot Version Boot Checksum Self Test 1. M12 (4xT1)* 5-11. DS2 Mode (DS2 #1-7) 1. 2 seconds* 2. 1 hour 3. 2 hours 4. 1E-5 5. 1E-6 4. DS3 XCV Threshold 2. G.747 (3xE1) 29. Set Multiple 12. DS3 Equipment Identification 30. Auto Enable Delay 2. Provisioning 1. T1/E1 State (T1/E1 #1-28) 1. IS 2. T1/E1 Line Coding (T1/E1 #1-28) 2. OOS 3. T1/E1 Line Length (T1/E1 #1-28) 4. T1/E1 Loopback Detection (T1/E1 #1-28) 4. 12 hours 5. 1 day 6. 2 days 7. 7 days 3. Service States 2. Card 1B 3. Facility Service States T1/E1 #1-28 29. DS3 30. Protection Threshold (1-28): 1* 30. Set Multiple 1. Perform Manual Switch 4. Protection 5. Save Provisioning 5. T1/E1 Circuit Protection (T1/E1 #1-28) 6. T1/E1 Line Identification (T1/E1 #1-28) 7. T1/E1 XCV Threshold (T1/E1 #1-28) 2. Minimum Switching Period (sec.) (10*) 6. Restore Factory Defaults 1. Disabled 7. Card Reset 2. 1 Minute 3. 5 Minutes* 8. Auto Save 1. Disabled 2. Enabled* 9 . Loopback Timeout 10 . Card Pair ID 1. AMI 2. B8ZS/HBD3* 2. CSU (T1 Only) 3. NIU (T1 Only) T1: 1. 0-133 ft* 2. 133-266 ft 3. 266-399 ft 1. Disabled* 1. Disabled 2. Enabled* 4. 399-533 ft 5. 533-655 ft E1: 1. 0-6dB Loss 1. Disabled* 2. 1E-3 3. 1E-4 4. 1E-5 5. 1E-6 3. Maximum Switch Threshold (3*) 2. Enabled 3. Auto Enable* 2. T1/E1 Interfaces 1. Card 1A 1. Disabled T1: 1. Data Mode 2. Tributary 3. Analog Network 4. Digital Line/Net 5. CODEC Line/Net 6. Remote Loopback 7. CSU Loopback 8. CSU LB w/BERT 9. NIU Loopback 4. 10 Minutes 5. 15 Minutes 6. 30 Minutes 7. 45 Minutes 8. 60 Minutes 10. NIU LB w/BERT 11. Line BERT T1/E1 Loopbacks (T1/E1 #1-28) E1: 29. DS3 Loopbacks 3. Status 1. Data Mode 1. Data Mode 2. Line Loopback 3. Digital Loopback 2. Tributary 3. Analog Network 4. Remote Loopback 5. Remote ALL T1/E1 4. Digital Line/Net 5. CODEC Line/Net 6. Remote Loopback 7. Line BERT 30-36. DS2 #1-7 Loopbacks 1. Data Mode 2. Network Loopback 37. Reset ALL Tests 38. Pattern 4. Test 1. Near End Daily 2. Near End Quarter Hourly 3. Far End Daily 1. DS3 Statistics 5. Performance Monitoring 2. T1/E1 Statistics 3. Clear ALL Statistics Note: An asterisk (*) indicates default setting 1. QRSS 2. ALL ONES 3. ALL ZEROES 4. 2 in 8 (2:6) 5. 1 in 8 (1:7) 6. 2 ^15-1 INV 4. Far End Quarter Hourly 5. Near End Daily Thresholds 6. Near End Quarter Hourly Thresholds 7. Near End Daily Thresholds 8. Near End Quarter Hourly Thresholds 1. Near End Daily 2. Near End Quarter Hourly 3. Near End Daily Thresholds 4. Near End Quarter Hourly Thresholds Warranty:ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Modify Date : 2004:08:11 17:16:11Z Create Date : 2004:02:06 16:40:53Z Creator : FrameMaker 7.0 Page Count : 2 Page Mode : UseNone About : uuid:e3c36a2b-dbc5-4216-810f-4ff5d4bd76ce Producer : Acrobat Distiller 6.0 (Windows) Mod Date : 2004:08:11 17:16:11Z Creation Date : 2004:02:06 16:40:53Z Creator Tool : FrameMaker 7.0 Document ID : uuid:1555e044-4840-41d8-8fda-f2e05629f349 Format : application/pdf Title : untitled Tagged PDF : YesEXIF Metadata provided by EXIF.tools