Adtran Netvanta 3448 Users Manual 61200821E1 13A
3448 to the manual f1c21494-4590-e504-995c-dd72247b9e88
2015-01-24
: Adtran Adtran-Netvanta-3448-Users-Manual-345251 adtran-netvanta-3448-users-manual-345251 adtran pdf
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
For more detailed documentation, visit us online at www.adtran.com. ® Quick Start Guide NetVanta 3448 Router P/N 1200821E1 GETTING STARTED 4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Pressto activate the AOS CLI. Two configuration methods are available for your NetVanta router: • Web-based GUI 5. Enter enable at the > prompt. • AOS Command Line Interface (CLI) 6. Enter the enable password when prompted. The default password is password. The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations. The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application. ACCESS THE GUI You may access the web-based GUI from any web browser on your network by following these steps: 1. Connect the router to your PC using the ETH 0/1 port on the back of the unit. 2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for instructions.) CONFIGURE THE UNIT’S IP ADDRESS The following steps create an IP address and subnet mask for ETH 0/1. If you are not sure what IP address to assign, please contact your network administrator. 1. At the # prompt, enter config terminal. 2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for the Ethernet port located on the rear of the unit. 3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1. 4. You will then be prompted for the username and password (the default settings are admin and password). 3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the Ethernet port using a 24-bit subnet mask. 5. The initial GUI screen appears. 4. Enter ip route 0.0.0.0 0.0.0.0 192.22.72.2 to add a default route to the route table. If necessary, contact your network administrator to obtain the IP address (and subnet mask) for your particular configuration. 5. Enter no shutdown to activate the interface to pass data. 6. Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode. ACCESS THE CLI Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta router CONSOLE port, you need the following items: • VT100 terminal or PC (with VT100 terminal emulation software) • Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end 1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit. 2. Connect the other end of the serial cable to the terminal or PC. 3. Provide power to the unit as appropriate. See the NetVanta 3000 Series Hardware Installation Guide (provided on the ADTRAN OS System Documentation CD) for more details. Quick Start Guide, 61200821E1-13A, July 2006 Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. If IP routing is enabled on the unit, do NOT set a default gateway. Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2006 ADTRAN, All Rights Reserved For more detailed documentation, visit us online at www.adtran.com. ® Quick Start Guide NetVanta 3448 Router P/N 1200821E1 45 V NETVANTA 3448 REAR PANEL LAYOUT ENABLE TELNET ACCESS CONSOLE PINOUTS The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password. 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions. 3. Enter login to initiate Telnet access. 4. Enter password adtran to change the login password for the Telnet sessions. 5. Enter exit to return to the Global Configuration mode. 6. Verify that the prompt of your unit displays (config)#. 7. Enter do write memory to save the current configuration. CONFIGURE YOUR APPLICATION More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes. Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com. Quick Start Guide, 61200821E1-13A, July 2006 Pin Name Description 1 DCD Data Carrier Detect (output) 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR 5 SG Signal Ground 6 — Tied to Pin 1 (output) 7 — Unused 8 — Tied to Pin 1 (output) 9 — Unused Data Terminal Ready (input) ETHERNET PINOUTS (ETH 0/1, ETH 0/2, ETHERNET SWITCH PORTS 1 TO 8) Pin Name Description With PoE Upgrade (Switch Ports 1 to 8 only) 1 TX1 Transmit Positive PoE Negative Rail 2 TX2 Transmit Negative PoE Negative Rail 3 RX1 Receive Positive PoE Positive Rail 4, 5 — 6 RX2 7, 8 — Technical Support 1-888-4ADTRAN (1-888-423-8726) Unused Unused Receive Negative PoE Positive Rail Unused Unused Copyright © 2006 ADTRAN, All Rights Reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Page Count : 2 Page Mode : UseNone XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:18b0f12f-ad5b-4906-b990-5a3752bd2991 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : FrameMaker 7.0 Modify Date : 2006:06:26 09:04:18Z Create Date : 2000:03:01 14:20:16Z Document ID : uuid:19165827-07a1-44c7-ae3b-f10c31d9a174 Format : application/pdf Title : 61200821E1-13A.fm Creator : lkeyes Author : lkeyesEXIF Metadata provided by EXIF.tools