Advance Security R54 Car Alarm Receiver User Manual CA Elite 6 series Install rev A 4 13 09

Advance Security Inc Car Alarm Receiver CA Elite 6 series Install rev A 4 13 09

Contents

user manual 1

12010 Audiovox Electronics Corporation. All rights reserved.PROFESSIONALSERIESRemote Start with Keyless EntryInstallation GuideCA6150RX
2 2010 Audiovox Electronics Corporation. All rights reserved.Before You Begin ...................................................................................... 3Wire Connection Guide ........................................................................... 48 Pin Main Harness ................................................................................... 53 Pin Parking Light Harness ..................................................................... 86 Pin Start Harness ................................................................................... 84 Pin Auxiliary Harness .......................................................................... 102 Pin Door Lock Output Harness ........................................................... 11Additional Ports ...................................................................................... 15Antenna / LED / Programming Port ....................................................... 15DBI Port.................................................................................................... 15Tracking Port ........................................................................................... 15Set Up & Programming .......................................................................... 16Transmitter Programming ........................................................................ 16Manual Feature Programming................................................................. 16Programming Feature Banks .................................................................. 17Tach Programming .................................................................................. 18Smart Tachless.Mode ............................................................................. 18Feature Descriptions ............................................................................. 19Transmitter Button Functions ............................................................. 22Remote Start Shutdown Diagnostics ................................................ 23System Layout......................................................................................... 24Table of Contents
32010 Audiovox Electronics Corporation. All rights reserved.PROFESSIONAL INSTALLATIONSTRONGLY RECOMMENDEDInstallation Precautions:Roll down window to avoid locking keys in vehicleduring installationAvoid mounting components or routing wires nearhot surfacesAvoid mounting components or routing wires nearmoving partsTape or loom wires under hood for protection andappearance Technical Support (800) 421-3209or go tohttp://techservices.codesystems.comUse a Digital Multi Meter for testing and verifyingcircuits. DO NOT USE A TEST LIGHT, OR"COMPUTER SAFE PROBE" as these can set off airbags or damage vehicle computers.Use grommets when routing wires through metalsurfacesBEFORE YOU BEGIN
4 2010 Audiovox Electronics Corporation. All rights reserved.6 Pin Start Harness4 Pin Auxiliary Output Harness8 Pin Main Harness3 Pin Parking Light Harness
52010 Audiovox Electronics Corporation. All rights reserved.2 Pin Lock Output Harness1 VIOLET/BLACK AUX 1This wire provides a ( - ) 500mA output capable of driving relays. For Control ofoptional accessories (i.e. Power Window/Sunroof, etc.).To activate refer to the transmitter button configuration chart. Please refer to theselectable options for timing.8 Pin Main Harness2 BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )This wire provides a ( - ) 500mA output for 30 seconds when the system isdisarmed capable of driving relays.Locate the vehicle’s dome light or pin switch wire.Verification: This wire will register positive voltage or ground when thevehicle's dome light is turned ON.3 BROWN/BLACK HORN OUTPUT ( - )Locate the vehicle’s horn wire.Verification: This wire will register at positive voltage and registerground when the horn switch is pressed.Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low currentoutput, 500mA.
6 2010 Audiovox Electronics Corporation. All rights reserved.Fused +12 VoltBattery Source308787a86 85BLUE/BLACK ActiveOutput Wire VATS Control ModuleMatching Value ResistorIgnition SwitchVATS Wire #1, WHITE or WHITE/BLACKVATS Wire #2, WHITE or VIOLET/WHITEX CUTGM VATSFused +12 VoltBattery Source308787a86 85BLUE/BLACK Active Output Wire To Vehicle's 2nd or 3rd Ignition Wire Jump To PINK Ignition Output Wire From Control Module Ignition 3 Accessory 2/3Fused +12 VoltBattery Source308787a86 85BLUE/BLACK Active Output Wire To Vehicle's 2nd or 3rd Accessory Wire Jump To ORANGE Accessory Output Wire From Control Module4 RED/WHITE TRUNK RELEASE OUTPUT ( - )Locate the vehicle’s trunk release wire at the trunk release switch.Verification: This wire will register either positive voltage or ground whenthe trunk release is activated.This is a low current output, 500mA.5 BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )The Active Output/Ignition 3 output wire provides a ground output when the remotestart function is activated and remains until 4 seconds after the remote start isshutdown. The Ignition 3 output wire can be used for several functions listedbelow. If this wire will be used for multiple application's a 1 amp diode is requiredin-line with the stripe facing the control module.Factory transponder (coded key) bypass.General Motors VATS bypass, see the following diagram. Use an SPDT relay (notsupplied).Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied).Accessory 2/3 output, see the following diagram. Use an SPDT relay (notsupplied).
72010 Audiovox Electronics Corporation. All rights reserved.6 PURPLE/WHITE TACH INPUT Locate the vehicle’s ignition coil or fuel injector in the engine compartment.Verification: Test using the following procedure:1. Set voltmeter to AC VOLTS.2. Attach positive lead of a volt meter to a constant 12-volt source.3. Attach negative lead of a volt meter to the wire to be tested.4. Start the engine.5. Have someone press on the gas pedal slightly as you monitor the meter. Ifconnected to the correct wire, the voltage reading will increase as the engine’sRPM increases.Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coilor fuel injector.7 GRAY HOOD PIN INPUT ( - )Install a Hood Pin Switch and connect to the GRAY wire. This connection isrequired for Remote Start.Verification: This wire when connected will register ground when thevehicle's hood is opened.Connect the GRAY wire to the hood pin.NOTE: Be sure to loom the wire, and seal the grommet.8 BROWN/RED BRAKE INPUT ( + )Locate the vehicle’s brake light wire at the brake pedal mounted switch.Verification: This wire registers positive voltage when the brake pedal ispressed.Connect the BROWN/RED wire to the vehicle’s brake light wire.
8 2010 Audiovox Electronics Corporation. All rights reserved.6 Pin Start Harness1 PURPLE STARTER OUTPUT ( + )Locate the vehicle starter wire.Verification: This wire registers voltage only when the key is turned to theSTART position.Verification:The starter wire registers voltage when the key is turned to theSTART position.Connect the PURPLE wire to the vehicle starter wire.1 BLACK GROUNDConnect the BLACK wire to a solid chassis ground point using a ring terminal andself tapping screw (not supplied). Scrape away paint from the grounding point toensure a good connection. The recommended grounding point is a metal surfacein the driver’s side kick panel area.NOTE: Do not ground the BLACK wire with any other vehicle components.3 Pin Parking Light Harness2 WHITE/RED PARKING LIGHT INPUT3 WHITE PARKING LIGHT OUTPUTLocate the parking light output wire at the vehicle’s light switch.Verification: This wire registers positive voltage when the parking lights areturned on.Positive switching Parking Lights:Connect the WHITE/RED wire to a 15 Amp max fused battery source.Connect the WHITE wire to the parking light output wire.Negative switching Parking Lights:Connect the WHITE/RED wire to a good chassis ground.Connect the WHITE wire to the parking light output wire.
92010 Audiovox Electronics Corporation. All rights reserved. 2 RED BATTERY 12V ( + )Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.Verification: This wire will register ( + ) voltage in all positions of the ignitionswitch.Connect the RED wire to the constant 12 Volt battery wire.NOTE: Remove all fuses until all connections are made.3 ORANGE ACCESSORY 1 ( + )Locate the vehicle’s accessory wire at the ignition switch.Verification: This wire registers voltage when the key is turned to ACC(Accessory) and the ON (or RUN) position. The voltage drops out when thekey is turned to the START (or CRANK) position.Connect the ORANGE wire to the vehicle’s accessory wire.4 PINK/WHITE IGNITION 2 ( + )Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).Verification: This wire registers voltage when the key is turned to the ON (orRUN) position, but not the ACC (Accessory) position. The voltage does notdrop out when the key is turned to the START (or CRANK) position.Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.Programmable output: IGN, ACC, Start. 5 RED BATTERY 12V ( + )Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.Verification: This wire will register ( + ) voltage in all positions of the ignitionswitch.Connect the RED wire to the constant 12 Volt battery wire.NOTE: Remove all fuses until all connections are made.
10 2010 Audiovox Electronics Corporation. All rights reserved.3 GREEN/WHITE FACTORY ARM /PULSE AFTER SHUTDOWN ( - )This wire will supply a ( - ) 500mA pulse both upon arming the system and afterthe remote start shuts down. This is typically used to re-lock the vehicle’s doors ifthey unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remotestart shutdown. 6 PINK IGNITION 1 ( + )Locate the vehicle’s ignition wire at the ignition switch.Verification: This wire registers voltage when the key is turned to the ON (orRUN) position. The voltage does not drop out when the key is turned to theSTART (or CRANK) position.Connect the PINK wire to the vehicle’s Ignition wire.This wire is also used for Ignition 1 Output.4 Pin Auxiliary Output Harness1 LT GREEN/BLACK FACTORY DISARM /PULSE BEFORE START ( - )This wire will supply a ( - ) 500mA pulse both upon disarming the system and whenthe remote start feature is activated. Locate the factory perimeter alarm disarmwire from the key cylinder inside the drivers door.Verification: This wire registers ground if the key is turned to the unlockposition in the driver’s door cylinder.Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.2 LT BLUE PULSE AFTER START ( - )This wire will supply a ( - ) 500mA pulse upon successful completion of the remotestart activation sequence and is typically used to re-lock the vehicle’s doors uponremote start if necessary.
112010 Audiovox Electronics Corporation. All rights reserved. 4 BLACK/YELLOW PULSE DURING CRANK ( - )Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)Verification: This wire registers voltage only in the start (crank) position ofthe ignition switch.Connect the BLACK/YELLOW wire as shown in the diagram below. Use an SPDTrelay (not supplied).F us e d +12 VoltB a tte r y S ource308787a86 85BLACK/YELLOW PulseDuring Crank WireTo Vehicle's 2nd S tarter Wire Jump To PUR PLE Starter Output Wire From The C ontrol Module2 Pin Lock Output Harness1 BLUE UNLOCK ( - )2 GREEN LOCK ( - )The door lock / unlock outputs are designed to control several different types ofsystems which may require additional parts. Please review the wire and locationchart to see which type of door lock system is in your vehicle. The most commontypes are shown in the following diagrams.
12 2010 Audiovox Electronics Corporation. All rights reserved.Negative Switching LocksAll Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /unlock switch.Verification: These wires will register ground when the Lock and Unlockswitches are activated.Connect the GREEN and BLUE wires shown in the diagram below.LockUnlockVehicle Door Lock Control RelaysGREEN (-) Lock OutputBLUE (-) Unlock OutputNegative Locks:Positive Switching LocksAll Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /unlock switch.Verification: These wires will register positive voltage when the Lock andUnlock switches are activated.Connect the GREEN and BLUE wires shown in the diagram below.LockUnlock8787a86 85308787a86 8530Vehicle Door Lock Control RelaysFused +12 Volt Battery SouceFused +12 Volt Battery SouceGREEN (-) Lock OutputBLUE (-) Unlock OutputPositive Locks:
132010 Audiovox Electronics Corporation. All rights reserved.Reverse Polarity Locks (5-Wire Door locks)All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /unlock switch.Verification: These wires will rest at ground and register positivevoltage when the Lock and Unlock switches are activated.Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagrambelow using (2) SPDT relays (not supplied).LockUnlock8787a86 85308787a86 8530Fused +12 Volt Battery SouceFused +12 Volt Battery SouceGREEN (-) Lock OutputBLUE (-) Unlock OutputReverse Polarity Locks:XCutXCutTo Door Lock MotorTo Door Lock MotorNegative Multiplexed LocksAll Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /unlock switch.Verification: This wire will show variable ground when the switch is activated.Please consult the wire and location chart for specific resistor values foryour vehicle.Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagrambelow using (2) SPDT relays (not supplied).LockUnlockVehicle Door Lock Control RelaysGREEN (-) Lock Output BLUE (-) Unlock OutputMultiplex Locks:8787a86308787a863085 85Fused +12 VoltBattery SourceGroundResistor
14 2010 Audiovox Electronics Corporation. All rights reserved.Positive Multiplexed LocksAll Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /unlock switch.Verification: This wire will show variable positive voltage when the switch isactivated. Please consult the wire and location chart for specific resistorvalues for your vehicle.Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagrambelow using (2) SPDT relays (not supplied).LockUnlockVehicle Door Lock Control RelaysGREEN (-) Lock Output BLUE (-) Unlock OutputMultiplex Locks:8787a86308787a863085 85Fused +12 VoltBattery SourceResistorAdding Aftermarket ActuatorsAfter installing aftermarket actuators, (not supplied). Connect the GREEN andBLUE wires shown in the diagram below using (2) SPDT relays (not supplied).308787a86 85Fused +12 VoltBattery SourceDoor Lock Actuator308787a86 85ChassisGroundChassisGround GREEN (-) Lock Output BLUE (-) Unlock OutputFused +12 VoltBattery SourceM
152010 Audiovox Electronics Corporation. All rights reserved.Data Bus Interface PortThis 4 pin port is used for Flashlogic Door Lock and Transponder DatabusInterfaces to communicate with the vehicle's Databus. When using the DBI port tocontrol the Flashlogic Door Lock and Transponder Interface modules thefollowing options may be available. Please refer to the D2D (Data to Data)function list available per vehicle on the tech service web site.Tach Input Brake Safety Shut DownTrunk/Hatch Open Diesel Glow Plug InputDoor Lock Control Passlock / Passkey Interface (GM Only)Dome Light Supervision Transponder Interface ActivationFactory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keylesscontrols system)Antenna / LED / Programming PortMount the supplied antenna/receiver to a clear spot on the vehicle's windshieldthat will not block the driver's vision. A good location is usually high on thewindshield near the rear view mirror. Be careful not to mount the antenna/receiveron any metallic window film, as this will effect system range. Route the antenna/receiver cable to the control module and plug into the antenna port.Additional PortsTracking PortThis 4 pin port is used for Code Alarm Car Link or Vehicle Tracking accessories.
16 2010 Audiovox Electronics Corporation. All rights reserved.Manual Feature Programming - Feature Bank 2 - 41. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 seconds the system will chirp (3) three times.4. Use the valet/override button to advance through each option bank. Forfeature programming advance to Feature Bank 2, 3 or 4, which is (4) four,(5) five, and (6) six chirps.5. Use the transmitter button to scroll through the selections in each featurebank, the system will chirp to match the feature number.6. Press the transmitter button to change the desired feature. The LED willflash indicating the changed feature.Defaulting All Features: Pressing the button anytime while in any of thefeature banks will default all features and return you to feature bank 2 - 4 chirps.NOTE: The system will remain in feature programming mode as long as theignition is on, there is no time limit. To exit programming turn the IGNITION OFF.Set Up & ProgrammingTransmitter Programming - Feature Bank 11. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 seconds the system will chirp (3) three times.4. Press 1 button of each transmitter you wish to program.5. The system will respond with 1 chirp for each accepted transmitter.6. Pressing the override button at anytime during programming will advance tothe next bank.NOTE: The system will exit transmitter programming after 15 seconds of inactivity.NOTE: This system has 1 button programming which programs all channels of thesystem.NOTE: The system will hold up to 4 transmitters in memory, programming a 5thtransmitter will erase the oldest transmitter in memory.NOTE: This system has PTN - Programmed Transmitter Notification. Each time theignition is turned ON, the LED will flash the number of transmitters programmed tothe system.
172010 Audiovox Electronics Corporation. All rights reserved.Feature Bank 1 - 3 ChirpsTransmitter Programming Refer to transmitter programming.Feature Bank 3 - 5 ChirpsOutput Control 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1 Extended Lock Pulse 1 Second 3.5 Seconds1 Second Lock, Double Pulse Unlock 30 Second Lock, Double Pulse Unlock Double Pulse Lock, 1 Second Unlock 2 Factory Disarm Factory Disarm 2nd Unlock Start Status3 Ignition Controlled Locks OFFLock and Unlock Lock Only Unlock Only 4 Horn Output Timing 16mS 10mS 30mS 40mS 50mS5 Real Panic ON OFF6AUX 1 Push and Hold LatchedLatched until IGN ON
18 2010 Audiovox Electronics Corporation. All rights reserved.Tach ProgrammingThe unit will not operate unless a tach signal is programmed or thetachless option is turned ON. If an attempt is made to start the vehicle via theremote start without first programming tach, the unit will flash the parking lights 7times indicating tach has not been learned and stored. If the tach rate is notproperly programmed to the specific vehicle, the unit may not realize that thevehicle is running in certain instances and reengage the starter motor.The Remote Start unit will learn the tach rate of most vehicle's single coil, multiple coilpacks, or single injector. To learn tach:1. Turn the ignition key to the ON position.2. Press and release the valet/override button 3 times.3. Immediately turn the ignition key OFF.4. Press and hold the valet/override button, then start the vehicle usingthe key.5. When the unit senses the tach signal, the parking lights will begin toflash.6. Allow the vehicle to settle to a normal idle speed.7. Release the valet/program push-button switch. The parking lights willturn on for 2 seconds indicating that the learned tach signal is storedand the unit has exited tach learn mode.NOTE: If the unit fails to learn tach rate due to an improper tach connection or apoor tach source, the parking lights will not flash. To correct this situation, locateand connect the PURPLE/WHITE wire to the proper tach signal, and then repeatthe tach learn routine.Smart Tachless ModeSmart Tachless Mode is available only if a tach signal has never been learned tothe system and when activated will automatically change the Tach Mode featurein option programming to Tachless without the need to enter the featureprogramming mode.1. Activate the remote start. The parking lights should begin flashing 7times indicating no tach signal has been learned.2. Within the 7 flash time period, press and hold the button.3. The system will chirp 1 time indicating the system is now in tachlessmode.
192010 Audiovox Electronics Corporation. All rights reserved.Feature Bank 2 - Security1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/unlock a second time will activate the arm/disarm chirps respectively. Thesystem will only sound the arm/disarm chirps upon a second press of thelock/unlock buttons.OFF - normal arm/disarm chirps upon the first press of lock/unlock.Feature DescriptionsFeature Bank 3 - Output Control1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock outputwires.1 Second - Single 1 second lock pulse, single 1 second unlock pulse.3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1second unlock pulse.30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double1 second unlock pulse.Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1second unlock pulse.2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarmoutput.Factory Disarm - Single 1 second pulse with unlock and remote startactivation.2nd Unlock - Single 1 second pulse with 2nd press of unlock.Start Status - Continuous ( - ) output during the remote start cycle.
20 2010 Audiovox Electronics Corporation. All rights reserved.3 - Ignition Controlled Locks: Control of door locks when the ignition is cycledON or OFF.OFF - Door locks not activated by ignition.Lock and Unlock - Doors lock when ignition is turned on and unlock whenignition is turned off.Lock Only - Doors lock when ignition is turned on only.Unlock Only Doors unlock when ignition is turned off only.4 - Horn Output Timing: Control the minimum horn pulse time in milli seconds,some vehicle will require a longer pulse to activate the factory horn.16mS 10mS 30mS 40mS 50mS5 - Real Panic: Controls the panic out when triggered from the transmitter.ON - Randomized horn honks when panic is triggered.OFF - Standard pattern horn honks when panic is triggered.Feature Bank 4 - Remote Start Control1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF.2 - Run Time: Controls the time in minutes that the vehicle will stay runningunder control of the remote start until the system times out. The system may alsobe shut down at any time by use of the transmitter or system shutdowns.3 - Running Lights: Controls the WHITE parking light output wire during remotestart.Steady - Parking lights constant during the remote start cycle.Flashing - Parking lights flash at a slow pace during the remote start cycle.6 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.Push and Hold - Output is continuously active until transmitter button isreleased.Latched - Output stays active until button is pressed again.Latched until IGN ON - Output stays active until the ignition is turned on.
212010 Audiovox Electronics Corporation. All rights reserved.4 - Tach Mode: Determines how the system monitors the engine running duringremote start.Tach - Hard wired directly to the tach wire of the vehicle to monitor ACvoltage.Tachless (Crank Average/Voltage) - Determines crank time by averaging thelast 8 times the vehicle was started with the key and then monitors thechange in voltage after remote start.Hybrid (Crank Average / No Voltage) - Determines crank time by averagingthe last 8 times the vehicle was started with the key.DBI Port - Monitors the vehicle’s tach rate through an interface moduleconnected to the DBI port.5 - Voltage Level: The voltage variance for remote start when set to tachless.(see tach mode)HIGH - The variance in battery voltage from before the remote startis activated to after the engine is running must be greater than 0.5 volts.LOW - The variance in battery voltage from before the remote startis activated to after the engine is running may be less than 0.5 volts.6 - Crank Time: Preset output times for the PURPLE starter wire.1 Second 0.8 Seconds 1.5 Seconds 2 Seconds 4 Seconds7 - Crank Average / Crank Time: The length of time in which the remote startwill crank the vehicle’s starter.Crank Average - Determines crank time by averaging the last 8 times thevehicle was started with the key.Preset Time - Preset starter output time. (see crank time)8 - Gas / Diesel: Selects engine type and delay time for the starter output wireduring remote start activation.Gas - Gasoline engine, no delay for the starter output wire.10 Second Delay - Diesel engine, delays the starter output wire for 10seconds after the ignition has been powered up by the remote start.15 Second Delay - Diesel engine, delays the starter output wire for 15seconds after the ignition has been powered up by the remote start.20 Second Delay - Diesel engine, delays the starter output wire for 20seconds after the ignition has been powered up by the remote start.45 Second Delay - Diesel engine, delays the starter output wire for 45seconds after the ignition has been powered up by the remote start.
22 2010 Audiovox Electronics Corporation. All rights reserved.9 - Single / Double Pulse Start: Switches the remote start activation betweena single or double press from the transmitter.10 - IGN 2 Output: Programmable high current output.Ignition 2 - Ignition output during remote start.Accessory - Accessory output during remote start.Start / Crank - Crank output during remote start.11 - 2 or 3 Hour Start: When activated, the remote start will activate and run forthe programmed time and shut down every 2 or 3 hours.Transmitter Button Functions1 Way TransmitterLock Unlock Car Find / PanicStart Operation MethodLock X Press and ReleaseUnlock X Press and ReleaseTrunk X Push and Hold (3 Sec) AUX 1 X X Push and Hold (3 Sec) Car Finder X Press and ReleasePanic X Push and Hold (3 Sec) Remote Start XPress and Release (1 or 2 times depending on selectable option) Remote Start Shut DownXPush and Hold (3 Sec) Run Time ExtentionXPress and Release 4 times.2 / 3 Hour Start XIgnition ON/OFF, Press and Hold Valet Button, Press Start 4 timesDaily Start Timer X X Press Lock + Start
232010 Audiovox Electronics Corporation. All rights reserved.Remote Start Shutdown DiagnosticsIf the remote start shuts down or fails to start, the parking lights will flash one ofthe patterns below indicating the shutdown input.To manually enter diagnostics and view the last shutdown, turn the ignition ONand press and release the button.LED FLASHES SHUTDOWN ZONE3 Flashes Hood InputBrake Input4 Flashes Remote Start Valet Mode7 Flashes Tach not learned / Crank Average not learned
24 2010 Audiovox Electronics Corporation. All rights reserved.LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )LT BLUE PULSE AFTER START ( - )GREEN/WHITE FACTORY ARM / PULSE AFTER SHUTDOWN ( - )BLACK/YELLOW PULSE DURING CRANK ( - )GREEN LOCK ( - )BLUE UNLOCK ( - )PURPLE STARTER OUTPUT - MOTOR SIDE ( + )RED BATTERY 12V ( + )ORANGE ACCESSORY 1 ( + )PINK/WHITE IGNITION 2 ( + )RED BATTERY 12V ( + )PINK IGNITION 1 ( + )BLACK GROUNDWHITE/RED PARKING LIGHT INPUTWHITE PARKING LIGHT OUTPUTVIOLET/BLACK AUX 1 OUTPUT ( - )BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )BROWN/BLACK HORN OUTPUT ( - )RED/WHITE TRUNK RELEASE OUTPUT ( - )BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )PURPLE/WHITE TACH INPUTGRAY HOOD INPUT ( - )BROWN/RED BRAKE INPUT ( + )ANTENNALEDVALETDBI PORT TRACKING PORTCA6150RX
252010 Audiovox Electronics Corporation. All rights reserved.
26 2010 Audiovox Electronics Corporation. All rights reserved.Audiovox Electronics Corporation.Customer Service 1-800-421-3209WWW.CODE-ALARM.COMFCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interferencethat may cause undesired operation.Warning!Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.

Navigation menu